Machine Specifications; Technical Data; Noise Emission; Dust Emission - Jet JTS-600X Operating Instructions Manual

Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
The type and condition of the
sawblade is important in keeping the
noise level as low as possible.
This does not negate the fact that
extra safety equipment such as ear
protection must be used.

4. Machine specifications

4.1 Technical data

Machine Table
Right extension table
Rear extension table
Sliding table size 1000x255 mm
Max. travel of sliding table
Max. length of cut
Sawblade diameter
Blade bore diameter
Blade speed n
0
Cutting height at 90°/45°
Tilting range of blade
Max. width of rip cut
Dust port diameter
Weight
Mains 230V ~1/N/PE 50Hz
Motor output power 1,5kW (2HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Motor output power 1,5 kW (2 HP) S1
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection

4.2 Noise emission

Determined according to EN 1870-1
(Inspection tolerance 4 dB)
Workpiece plywood 16mm:
Acoustic power level
(according to EN ISO 3746):
Idling LwA
Operating LwA 101,8 dB (A)
Acoustic pressure level
(according to EN ISO 11202):
Idling LpA
Operating LpA
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
This information is intended to allow
the user to make a better estimation of
the hazards and risks involved.

4.3 Dust emission

The circular saw has been dust
emission evaluated.
At an air velocity of 20m/sec on the
dust port dia. 100mm:
Vacuum pressure
Volume flow
The TRK-value of 2 mg/m
exceeded.
800x350 mm
4.4 Content of delivery
800x270 mm
Machine stand
415x350mm
Sliding table
Crosscut table
660 mm
Crosscut fence
610 mm
Telescopic arm
Rare extension table
max 250 mm
Right extension table
30 mm
Rip fence with dual fence profile
4000 rpm
Rip fence support bar
80/54 mm Saw guard
90°- 45° Sawblade 250mm
610 mm Dust connection hose and Y-adapter
Hose tye
100mm
Push stick
145 kg
Operating tools
Assembly bag
Operating manual
11 A
Spare parts list
16A

4.5 Description of machine

4.7 A
16A
98,2 dB (A)
A......Crosscut fence
84,2 dB (A)
B.....Pull out lock knob
88,5 dB (A)
C....Crosscut stop
D.....Crosscut table
850Pa
565 m³/h
3
is not
Fig 1
5
E.....Sliding table
F.....Raving knife
G.....Saw guard
H....Dust connection hose
I.....Rip fence
J......Telescopic arm
K....Front cabinet cover
L....On/ Off switch
M....Sliding table lock
N....Blade rise handwheel
O....Blade tilt lock
P....Blade tilt handwheel
Q....Rip fence micro adjustment

5. Transport and start up

5.1 Transport and installation

For transport to the desired location
use a forklift or hand trolley. Make
sure the machine does not tip or fall
off during transport.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
The machine must be levelled in both
directions to assure good sliding
motion of the sliding table.
If possible, the machine must be
placed on rubber plates which act as
shock absorbers and reduce the noise
level.
For packing reasons the machine is
not completely assembled.

5.2 Assembly

If you notice any transport damage
while unpacking, notify your supplier
immediately. Do not operate the
machine!
Dispose of the packing in an
environmentally friendly manner.
Clean all rust protected surfaces with
a mild solvent.
Mounting machine stand:
Attach the side panels to the front and
rear panel with the supplied bolts, flat
washers and nuts.
Attach the 4 rubber pads.