Remaining Hazards; Machine Specifications; Technical Data; Noise Emission - Jet JTS-600X-M Operating Instructions Manual

Never use sawblades made from High
Speed Steel (HSS).
Take care that the selection of the saw
blade depends on the material to be
cut.
Remove defective sawblades
immediately.
A worn table insert must be replaced.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist
The moving sawblade in the work area
can cause injury.
Broken saw blades can cause injuries.
Thrown workpieces can lead to injury
Tipping of the workpiece due to
insufficient support can lead to injury.
Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
The type and condition of the
sawblade is important in keeping the
noise level as low as possible.
This does not negate the fact that
extra safety equipment such as ear
protection must be used.

4. Machine specifications

4.1 Technical data

Machine Table
Right extension table
Rear extension table
Sliding table size 1000x255 mm
Max. travel of sliding table
Max. length of cut
Sawblade diameter
Blade bore diameter
Blade speed n
0
Cutting height at 90°/45°
Tilting range of blade
Max. width of rip cut
Dust port diameter
Weight
Mains
Motor output power
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains
Motor output power 1,5 kW (2 HP) S1
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection

4.2 Noise emission

Determined according to EN 1870-1
(Inspection tolerance 4 dB)
Workpiece plywood 16mm:
Acoustic power level
(according to EN ISO 3746):
Idling
Operating
Acoustic pressure level
(according to EN ISO 11202):
Idling
Operating
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
This information is intended to allow
the user to make a better estimation
of the hazards and risks involved.

4.3 Dust emission

The circular saw has been dust
emission evaluated.
At an air velocity of 20m/sec on the
dust port dia. 100mm:
Vacuum pressure
Volume flow
The TRK-value of 2 mg/m
exceeded.
800x350 mm
800x270 mm
4.4 Content of delivery
415x350mm
Machine stand
Sliding table
660 mm
Crosscut table
610 mm
Crosscut fence
max 250 mm
Telescopic arm
30 mm
Rare extension table
4000 rpm
Right extension table
Rip fence with dual fence profile
80/54 mm
Rip fence support bar
90°- 45°
Saw guard
610 mm
Sawblade 250mm
100mm
Dust connection hose and Y-adapter
150 kg
Push stick
230V ~1/N/PE 50Hz
1,5kW (2HP) S1
9.6 A
16A
400V ~3/PE 50Hz
4.7 A
16A
LwA 98,2 dB (A)
LwA 101,8 dB (A)
LpA 84,2 dB (A)
LpA 88,5 dB (A)
850Pa
565 m³/h
3
is not
5
Operating tools
Assembly bag
Operating manual
Spare parts list

4.5 Description of machine

Fig 1
A......Crosscut fence
B.....Pull out lock knob
C....Crosscut stop
D.....Crosscut table
E.....Sliding table
F.....Raving knife
G.....Saw guard
H....Dust connection hose
I.....Rip fence
J......Telescopic arm
K....Front cabinet cover
L....On/ Off switch
M....Sliding table lock
N....Blade rise handwheel
O....Blade tilt lock
P....Blade tilt handwheel
Q....Rip fence micro adjustment

5. Transport and start up

5.1 Transport and installation

For transport to the desired location
use a forklift or hand trolley. Make
sure the machine does not tip or fall
off during transport.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
The machine must be levelled in both
directions to assure good sliding
motion of the sliding table.