Foundation And Positioning; Condensate Pump (Accessory) Water Flow - Lift Height - Trane CLCF Climate Changer Manual

Installation
Roller Movement
Units fitted with base frames may be moved on roller trolleys or tubular rollers (see Figure 5).
Figure 5 – Roller movement
FWD
Power supply
Capacities
Cooling capacity on water (1)
Heating capacity on water (2)
Fan motor
Fan power input (3)
Current amps (3)
Start-up amps
Air flow
minimum
nominal

Foundation and positioning

maximum
Main coil
Water entering/leaving connections
Space requirements
There must be adequate space at the installation site to carry out effective and safe maintenance and to dismantle
Electric heater (accessory for blower only)
any of the unit modules as necessary. From the access panel side of the unit, a working area of the unit width plus
Electric power supply
Heating capacity
300 mm is required. On the rear side of the unit, an access gangway of 600 mm is necessary for assembly purposes.
Hot water coil (accessory for blower only)
Foundation
Heating capacity (4)
G2 filter (filter box accessory)
Complete reinforced concrete foundations are suitable (see Figure 6a). Strip foundations may also be used (see
Quantity
Figure 6b). In the case of strip foundations, concrete or steel supports must be provided under every unit base frame
Dimensions ( LxWxth)
G4 filter (filter box accessory)
channels.
Quantity
For steel support construction (see Figure 7), the foundation must be of adequate strength to match the unit size.
Dimensions ( LxWxth)
Condensate pump (accessory)
The foundations must be level with no slope or unevenness.
Water flow - lift height
CAUTION!: Failure to provide a level plinth or support will result in doors jamming and air leaks from the casing.
Not available for FWD30 and FWD45
Sound level (L/M/H speed)
Figure 6a – Reinforced concrete foundation
Sound pressure level (5)
Sound power level (5)
Unit dimensions
Width x Depth
Height
Shipped unit dimensions
Width x Depth
Height
Weight
Colour
Recommended fuse size
Unit alone (aM/gI)
Figure 6b – Strip foundation
Unit with electric heater (gI)
(1) Conditions: Water entering/leaving temperature: 7/12 °C, Air inlet temperature 27/19°C DB/WB - Nominal air flow
(2) Conditions: Water entering/leaving temperature: 50/45 °C, Air inlet temperature 20°C DB - Nominal air flow
(3) At high speed with nominal air flow.
(4) Water entering/leaving temperature 90/70 °C, air inlet temperature 20 °C DB, Nominal air flow.
(5) A rectangular glass wool duct 1m50 long is placed on the blower.The measurement is taken in the room containing the blower unit.
Heat exchanger operating limits:
FWD:
*water temperature: max 100° C
*absolute service pressure: min 1 bar/max 11 bars
Accessories - Hot water coil:
*water temperature: min. +2° C/max. 100° C
*absolute service pressure: min 1 bar/max 11 bars
4 12
Technical Data
08
(V/Ph/Hz)
(kW) 5,2
(kW) 6,3
(type)
(kW) 0,23
(A) 1,1
(A) 3,2
(m /h) 490
3
(m /h) 820
3
(m /h) 980
3
(type)
(Dia) 3/4"
(V/Ph/Hz) 230/1/50
(kW) 2/4
(kW) 6,3
2
(mm) 386x221x8
-
(mm) -
(type)
(l/h - mm)
(dB(A)) 36/40/43
(dB(A)) 46/50/53
(mm) 890 x 600
(mm) 250
(mm) 933 x 644
(mm) 260
(kg) 32
(A) 8/16
(A) 16 (2kW),25 (4kW)
12 20
230/1/50
8,3 15
11,9 18,9
2 x direct drive centrifugal
0,46 0,65
2,2 3,1
5,5 9,3
980 1400
1650 2300
1970 2600
ISO R7 rotating female
3/4" 1 1/2"
230/1/50 or 400/3/50 400/3/50
8 10
12 17,4
2 2
486x271x8 586x321x8
2 2
486x264x48 586x314x48
Centrifugal
24 - 500
38/41/44 46/50/53
48/51/54 56/60/63
1090 x 710 1290 x 820
300 350
1133 x 754 1333 x 864
310 360
46 61
galvanised steel
8/16 8/16
40 (230V),3*16 (400V) 3*20
30 45
18,8 30,1
20,9 38,2
1,04 1,51
4,7 5,5
14,1 16,5
1800 2700
3000 4500
3600 5400
1 1/2" 1 1/2"
400/3/50 400/3/50
12 12
22,4 34,5
2 2
586*421*8 586*621*8
2 2
586*414*48 586*614*48
47/52/57 47/52/58
57/62/67 57/62/68
1290 x 970 1290 x 1090
450 650
1333 x 1008 1333*1133
460 660
76 118
8/25 8/25
3*25 3*25
UNT-PRC002-GB AH-SVX03C-GB