Warnings And Cautions; Camera Dome; Eyeball; Speeddome Ultra 8 Camera Dome - American Dynamics SpeedDome Ultra 8 Installation And Service Manual

Camera dome
Hide thumbs Also See for SpeedDome Ultra 8:
Table of Contents

Advertisement

Warnings and Cautions

Please review the following warnings and cautions
before you begin installation or service.
WARNINGS
!
WARNING!
ALWAYS USE:
• Proper safety equipment for the location and
type of installation.
• Proper lift equipment to reach the installation.
• Safety features of the lift equipment.
BE SURE:
• Electrical power is not connected to the dome
when connecting wires. Dome will move when
power is applied.
• Electrical power is not connected to nearby
fixtures that you might touch during installation.
WARNING!
DO NOT install this camera
!
dome where highly combustible or
explosive products are stored or used.
WARNING!
This dome runs on 24Vac.
!
DO NOT connect line voltage to this
dome.
North America power requirements: In
North America, this device is intended to
be supplied from a Class 2 power
supply. For outdoor installations, use
Class 3 wiring techniques, liquid-tight
conduit, or liquid-tight pipe.
This installation should be made by a
qualified service person and should
conform to all local codes.
!
WARNING!
EU power requirements: This product runs on
24Vac. In the EU, it is intended to be powered from
a Limited Power Source. A limited power source is
a certified source of SELV, and if inherently limited,
with 8 amps maximum output current, and a
maximum of 100VA available; or if not inherently
limited, fused with a maximum value of 3.3 Amps,
meeting section 2.11 of IEC950, and a maximum of
250VA available.

SPEEDDOME ULTRA 8 CAMERA DOME

INSTALLATION AND SERVICE GUIDE
The power supply can be obtained through
Sensormatic or through another source where the
provider can furnish the verification. This is
required to assure electrical safety in the product.
Stromanforderungen in der EU: Dieses Produkt wird
mit 24 V Wechselstrom betrieben. In der EU ist es für
den Betrieb durch eine begrenzte Stromquelle
vorgesehen. Eine begrenzte Stromquelle ist eine
zertifizierte SELV-Quelle (Schutzkleinspannung), bei
inhärenter Begrenzung mit einem maximalen
Ausgangsstrom von 8 A und 100 VA maximaler
Verfügbarkeit, bei nicht inhärenter Begrenzung mit einer
maximalen Sicherung von 3,3 A gemäß Abschnitt 2.11
der IEC950 und 250 VA maximaler Verfügbarkeit. Das
Netzteil kann über Sensormatic oder eine andere Quelle
bezogen werden, wobei der Anbieter den Nachweis der
Konformität bereitstellen sollte. Dies ist zur
Gewährleistung der elektrischen Sicherheit des
Produktes erforderlich.
CAUTION
• Cables:
-
Do not run data and power cables adjacent to or
in the same conduit as line voltage mains power.
-
SensorNet 485 networks require 22 AWG
unshielded cable. Do not exceed 32 devices per
cable run.
-
RS-422 networks require 22 AWG shielded cable.
Do not exceed 10 devices per cable run.
-
Manchester networks require 18 AWG shielded
cable. Do not exceed 3 devices per cable run.
• I/O PC board:
− Use a jeweler's 2.5mm (0.1in) slotted screwdriver
to tighten connector screws. Do not over tighten
these screws.
− Always terminate I/O board jumper E1 if the dome
connects at the end of a cable run.
Keep the dust cover to protect contacts should the
environmental PC board need to be removed
from the housing.
• When connecting the housing and eyeball
assembly to an outdoor housing remove both
slot covers to keep the camera from
overheating.
• If disassembling the dome:
− Dome contains electrostatic-sensitive devices!
Use a ground strap when handling PC boards.
− Once disassembled, parts of housing and eyeball
assembly are fragile and may break. Use extreme
care!
9 of 30
8200-0600-03, REV. B

Advertisement

Table of Contents
loading

Table of Contents