American Dynamics SpeedDome Ultra Installation And Service Manual
  1. Manuals
  2. Brands
  3. American Dynamics Manuals
  4. Security Camera
  5. SpeedDome Ultra
  6. Installation and service manual

American Dynamics SpeedDome Ultra Installation And Service Manual

American dynamics speeddome ultra housings: install guide
Hide thumbs Also See for SpeedDome Ultra:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Instructions
SpeedDome
Ultra
®

Camera Dome

Installation and Service
Manual
8000-1362-01, Rev. B

Advertisement

Table of Contents
loading

Related Manuals for American Dynamics SpeedDome Ultra

Summary of Contents for American Dynamics SpeedDome Ultra

  • Page 1: Camera Dome

    SpeedDome Ultra ® Camera Dome Installation and Service Manual 8000-1362-01, Rev. B...
  • Page 2 SpeedDome Ultra ® Camera Dome Installation and Service Manual 8000-1362-01, Rev. B MDR 4/97...

  • Page 3: Fcc Compliance

    This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 4: Table Of Contents

    Wall mounting using a corner bracket and an arm extension ... 2-13 Hard ceiling pendent mount... 2-14 Electrical box attachment ... 2-15 Adapter bracket for indoor SpeedDome housings ... 2-16 Dome setup and attachment... 2-17 Skirt and bubble attachment ... 2-20 Attaching the skirt to the top hat housing ...
  • Page 5 Chapter 3 “OUTDOOR” INSTALLATION... 3-1 BEFORE YOU BEGIN... 3-2 Safety ... 3-2 Verifying equipment and unpacking ... 3-2 Tools and equipment required ... 3-2 Parts check ... 3-2 I/O board detachment ... 3-2 INSTALLATION PROCEDURE ... 3-3 How to use this section ... 3-3 Mounting the dome’s base to the outdoor SpeedDome housing ...

  • Page 6: Preface

    Installation and service of this camera dome does not require detailed knowlege of how it it works or its circuits. However, if this information is required, order the following document. Theory for SpeedDome Ultra Camera Domes, document number 8000-1670-01. Questions?

  • Page 8: Chapter 1 Introduction

    SpeedDome Ultra Camera Dome INTRODUCTION n Product overview ...1-2 Describes how the dome works, its mounting methods, major components, and features. n Specifications ...1-9 Lists electrical, environmental, regulatory, and mechanical specifications for the dome. SPEEDDOME ULTRA CHAPTER...

  • Page 9: Product Overview

    PRODUCT OVERVIEW The SpeedDome Ultra camera dome (Figure 1-1) is part of a programmable network of camouflaged cameras. These devices enable security personnel, from a remote console, to track a target, near or far, even in low light. Small and unobtrusive, the dome can be used in...
  • Page 10 Standard Slot Cover with Lens (0500-6709-01) (Supplied with Final Assy., not Eyeball Assy.) 0351-1163-01 Install Kit Tripod Mount Optional Slot Cover with 0.5f Darker Lens (0500-6712-01) (0500-6709-03) SPEEDDOME ULTRA INTRODUCTION Screws (3), M3 x 8 PHP (5801-1051-120) Yoke Bracket (2) (0500-7254-01)

  • Page 11: Indoor Mounting Methods

    This bracket can also be used for outdoor housings. * These options come in white, but can be easily painted to match decor. SPEEDDOME ULTRA INTRODUCTION Clear bubble Silver bubble Smoked bubble...
  • Page 12 Figure 1-5. Indoor mounting structures (optional) RHIUH RHIUWM RHIULWM RHIUCM RHIUPND RHIUFB RHIUAB RHIU3x3, RHIU4x4 RHSDA SPEEDDOME ULTRA INTRODUCTION...

  • Page 13: Outdoor Mounting Method

    . The dome can precisely pan, tilt, ™ zoom and focus in one operation. This speed and accuracy enables one SpeedDome Ultra to offer better coverage than multiple fixed cameras. Transient Protection. The dome has extensive transient protection on its data input/output channels to protect against lightning and electrostatic discharge.

  • Page 14: Video System Dependent Features

    Certain dome features depend on the video system the dome is used with: Sensormatic Video Manager system with RS422 Sensormatic VM8, VM16, or VM96 systems American Dynamics AD2083-02 system. Following are features associated with each type of system. Video Manager System with RS422 Pan and tilt speeds of 0.5°...

  • Page 15: Installation And Service Features

    The dome can be located up to 250m (820ft) from the junction box. V-Phase Adjustment. The dome has a remote V- phase adjustment that enables synchronization to any line phase by one person at the control console. SPEEDDOME ULTRA INTRODUCTION The dome assembly has a...

  • Page 16: Specifications

    Immunity ... EN50082-1 (CE) Safety ... UL2044 Environmental Operating Temperature ... –10° to 50°C (14°–122°F) Relative Humidity ... 0 to 95% non-condensing Mechanical SPEEDDOME ULTRA INTRODUCTION Class A EN55022 Class B (CE) CSA 22.2 No. 1 (cUL) EN60950 (CE) 205 mm 1.36 kg...
  • Page 17 = zoom power (such as 12X) Example of a wide angle view with zoom power of 12X at 18 m from the camera: (.87 x 18)/12 = 1.2m or 4ft. (.634 x 18)/12 = .95m or 3ft. SPEEDDOME ULTRA 1-10 INTRODUCTION...
  • Page 18 “Indoor” SpeedDome Ultra Camera Dome INSTALLATION Chapter 2 In this chapter: n Before You Begin ...2-2 Things you need to do before you install the camera dome. n Installation Procedure ...2-3 Shows you how to mount the dome indoors to either a hard ceiling, tile ceiling, wall, electrical box, I-beam, or existing SpeedDome housing.

  • Page 19: Before You Begin

    Push the fingers away from the board while pushing on the I/O board with your index finger (Figure 2-1). Put the board aside in a safe place. Figure 2-1. Detaching the I/O board Dust Cover (Do Not Remove) SPEEDDOME ULTRA installation procedure,...

  • Page 20: Installation Procedure

    2. Set up the dome and attach it to its base: Dome setup and attachment ... 2-17 3. If used, you can attach an optional skirt and bubble to the top hat or SpeedDome housings: Skirt and bubble attachment... 2-22 Hard/Tile Ceiling Mounting The following methods show you how to mount the dome’s base directly to the surface of a hard ceiling...

  • Page 21: Tile Ceiling Surface Mounting

    4. Feed cables through the base, then go to “Dome Setup and Attachment”, page 2-17. INDOOR DOME INSTALLATION Figure 2-4. Mounting clip attachment 0500-7193-01 5801-1051-120 Figure 2-5. Base attachment to tile ceiling T-bar intersection SPEEDDOME ULTRA...

  • Page 22: Optional Mounting Structures

    Use narrow slots Use M6 nuts from Use M3 nuts from mounting structure mounting structure RHIUFB or RHIUAB RHIUWM SPEEDDOME ULTRA To Electrical To Plate Adapter Use narrow slots Use M3 nuts from Use M3 nuts from mounting structure mounting structure...

  • Page 23: Fixed" Mounting Bracket For Hard Ceilings Or 2X2 Ceiling Tiles

    S-Hook, open Chain, sash Support Bracket Hole in tile diameter: 178mm (7 in.) Vertical adjustment range: 38mm (1.5 in.) Ceiling space requirements for bracket assembly: 178mm (7 in.) less ceiling tile thickness SPEEDDOME ULTRA 0500-7455-01 8001-0466-01 0500-7507-01 0500-7509-01 0500-7465-01 5842-0500-020 5826-0500-020...
  • Page 24 [i] to the S-hook and its other end to a strong ceiling member. KEEP CHAIN AS TAUT AS POSSIBLE! CLOSE BOTH ENDS OF S-HOOK. DO NOT SECURE TO A SPRINKLER OR FIRE CON- TROL SYSTEM! 17. Go to “Dome Setup and Attachment”, page 2-17. SPEEDDOME ULTRA...

  • Page 25: Adjustable" Mounting Bracket For 2X4 Ceiling Tiles

    Bracket Hole in tile diameter: 178mm (7 in.) Vertical adjustment range: 38mm (1.5 in.) Horizontal adjustment: 711–1220mm (28–48 in.) Ceiling space requirements for bracket assembly: 178mm (7 in.) less ceiling tile thickness SPEEDDOME ULTRA 0500-7455-01 8001-0466-01 0500-7507-01 0500-7508-01 0500-7509-01 0500-7465-01...
  • Page 26 [j] to the S-hook and its other end to a strong ceiling member. KEEP CHAIN AS TAUT AS POSSIBLE! CLOSE BOTH ENDS OF S-HOOK. DO NOT SECURE TO A SPRINKLER OR FIRE CON- TROL SYSTEM! 13. Go to “Dome Setup and Attachment”, page 2-17. SPEEDDOME ULTRA...

  • Page 27: Wall Mounting Bracket

    4. Place cover [b] over the bracket and secure 2880-0011 2880-0073-01 using one M3x8 screw [c]. 5842-0300-020 5810-4091-120 5. Go to “Dome Setup and Attachment”, page 2-17. SPEEDDOME ULTRA 2-10 Use side hole for direct base attachment. Use center hole for top hat housing attachment. Base...

  • Page 28: Wall Mounting Using A Corner Bracket

    7. Go to “Dome Setup and Attachment”, page 2-17. Figure 2-10. Wall mounting using a corner bracket 0500-7472-01 2402-1254-01 5801-3051-120 0500-7664-01 0500-7663-01 5801-1051-120 5826-0200-020 2880-0011 2880-0073-01 5842-0300-020 5810-4091-120 SPEEDDOME ULTRA 2-11 Use side hole for direct base attachment. Use center hole for top hat housing attachment. Base...

  • Page 29: Wall Mounting Using An Arm Extension

    M3 locking nuts [e]. Feed cables as shown. 0500-7719-01 5801-2061-120 b. Top hat housing attachment. See “Top Hat Hous- 5826-0200-020 ing”, page 2-5. 2880-0011 2880-0073-01 6. Go to “Dome Setup and Attachment”, page 5842-0300-020 2-17. 5810-4091-120 SPEEDDOME ULTRA 2-12 Base...

  • Page 30: Wall Mounting Using A Corner Bracket And An Arm Extension

    M3 locking nuts 2880-0011 [h]. Feed cables as shown. 2880-0073-01 5842-0300-020 b. Top hat housing attachment. See “Top Hat Hous- 5810-4091-120 ing”, page 2-5. 8. Go to “Dome Setup and Attachment”, page 2-17. SPEEDDOME ULTRA 2-13 Base...

  • Page 31: Hard Ceiling Pendent Mount

    Base plate hole-to-hole dimensions 90mm (3.5 in.) Vertical Mounting 0500-3975-01 0500-3976-01 5801-4194-311 5840-0500-020 5826-0500-020 1400-0069-01 1417-0040-01 1417-0041-01 0500-7696-01 0500-7719-01 5826-0200-020 2880-0011 Purchased Part Base SPEEDDOME ULTRA 2-14 128mm (5 in.) 179mm (7 in.) 230mm (9 in.) Horizontal Mounting Direct Ceiling Attachment...

  • Page 32: Electrical Box Attachment

    Feed cables as shown. b. Top hat housing attachment. See “Top Hat Hous- ing”, page 3-5. 3. Go to “Dome Setup and Attachment”, page 2-17. Figure 2-14. Electrical box mounting structure 0500-7489-01 2804-1918-03 5826-0200-020 0500-7635-01 2804-1918-03 5826-0200-020 SPEEDDOME ULTRA 2-15 Base...

  • Page 33: Adapter Bracket For Indoor Speeddome Housings

    Mounting Structure and Install Kit Required 01RHSDA Adapter Bracket* a. Adapter bracket assembly * Only part used in this procedure is listed. SpeedDome Ultra Install Kit 0351-1109-01* b. Screw, PH, M3x * Only part used in this procedure is listed. Procedure 1.

  • Page 34: Dome Setup And Attachment

    JW2/JW3 Terminations* PINS Jumper locations are not relevant when the dome is hooked up to an RS422 network. SPEEDDOME ULTRA 2-17 Designation Alarm 3 Input (3.5mA sink) Alarm 2 Input (3.5mA sink) Alarm 1 Input (3.5mA sink) Alarm 0 Input (3.5mA sink)
  • Page 35 2mm above the surface of the connector. Keep the dust cover for use should you have to ship the base and I/O board back to the manufacturer. Figure 2-19. Reattaching the I/O board SPEEDDOME ULTRA 2-18 RS422 Test Pushbutton...
  • Page 36 The dome address can be set from 000 to 999. 14. Reattach the dome. Settings selected in step 13 will then be placed into dome memory. Lock SPEEDDOME ULTRA 2-19 This time, the dome will immediately begin its “homing” routine.

  • Page 37: Skirt And Bubble Attachment

    The skirt is not used in this case. Figure 2-22. Top hat skirt and bubble attachment To Secure T-Lanyard SPEEDDOME ULTRA 2-20 Insert T-lanyard exactly as shown in Figure 2-22 to ensure that the bubble is securely attached. Ensure that “T”...

  • Page 38: Attaching The Skirt To The Indoor Speeddome Housing

    “T” catch securely. 3. Push pins of the bubble into their respective receptacles and snap the bubble into place. Figure 2-24. Attaching the bubble to the indoor SpeedDome housing SPEEDDOME ULTRA 2-21 0500-7411-01 2.5ft 3200-0214-01...
  • Page 39 3. Lower the pole “vertically” (See following CAUTION). KEEP THE POLE VERTICAL! Turning the pole horizontally as you lower it can cause the camera dome to fall out of the tool and possibly break on the floor. 4. Remove the dome for service. SPEEDDOME ULTRA 2-22...
  • Page 40 Figure 2-25. How to use the install/removal tool Skirt or Bubble Attachment/Detachment Snap tool into pole. Attachment Dome Attachment (Reverse steps to detach) INDOOR DOME INSTALLATION Catch the notch and pull down. Detachment Line up Line up SPEEDDOME ULTRA 2-23 Turn until you feel a click.
  • Page 41 INDOOR DOME INSTALLATION SPEEDDOME ULTRA 2-24...
  • Page 42 “Outdoor” SpeedDome Ultra Camera Dome INSTALLATION Chapter 3 In this chapter: n Before You Begin ...3-2 Things you need to do before you install the camera dome. n Installation Procedure ...3-3 Shows you how to mount the dome to an existing outdoor SpeedDome housing.

  • Page 43: Before You Begin

    Push the fingers away from the board while pushing on the I/O board with your index finger (Figure 3-1). Put the board aside in a safe place. Figure 3-1. Detaching the I/O board Dust Cover (Do Not Remove) SPEEDDOME ULTRA installation procedure,...

  • Page 44: Installation Procedure

    SpeedDome housing... 3-4 2. Set up the dome and attach it to its base: Dome setup and attachment ... 3-5 3. Attach the skirt and bubble to the SpeedDome housing: Skirt and bubble attachment... 3-8 OUTDOOR DOME INSTALLATION SPEEDDOME ULTRA...

  • Page 45: Mounting The Dome's Base To The Outdoor Speeddome Housing

    3. Find the data/power cable from the outdoor interface board. Remove the connector from this cable. 4. Mount the SpeedDome Ultra camera dome’s base to the adapter bracket [a] (Figure 3-2). Use two of six screws [e] to attach the base to the bracket.

  • Page 46: Dome Setup And Attachment

    JW2/JW3 Terminations* PINS Jumper locations are not relevant when the dome is hooked up to an RS422 network. SPEEDDOME ULTRA Designation Alarm 3 Input (3.5mA sink) Alarm 2 Input (3.5mA sink) Alarm 1 Input (3.5mA sink) Alarm 0 Input (3.5mA sink)
  • Page 47 For reliable connections, all contacts should be at least 2mm above the surface of the connector. Keep the dust cover for use should you have to ship the base and I/O board back to the manufacturer. Figure 3-6. Reattaching the I/O board SPEEDDOME ULTRA RS422 Test Pushbutton...
  • Page 48 The dome address can be set from 000 to 999. 14. Re-apply ac power to the dome. Settings selected in step 13 will then be placed into dome memory. Lock SPEEDDOME ULTRA This time, the dome will immediately begin its “homing” routine.

  • Page 49: Skirt And Bubble Attachment

    2. Thread the three screws [b] of the bubble [c] into their respective mounting holes. Tight- en the screws to secure. Figure 3-9. Attaching the skirt and bubble to the outdoor SpeedDome housing OUTDOOR DOME INSTALLATION SPEEDDOME ULTRA...

  • Page 50: Chapter 4 Service

    SpeedDome Ultra Camera Dome SERVICE Chapter 4 In this chapter: n Before you begin ...4-2 Explains things you need to do and tools you need to have on hand before you service the camera dome. n Routine Troubleshooting...4-2 Contains procedures to help you isolate a problem to the base or housing and eyeball assembly.

  • Page 51: Before You Begin

    The quality of the video is poor 1-800-543-9740 The dome has no lens control. Read CAUTIONS below. SPEEDDOME ULTRA SERVICE DO NOT use this procedure if the dome functions but does not pan or tilt. Ship both the base and dome to the NRC for service.
  • Page 52 I/O board (Figure 4-2). Is the cable disconnected? • YES: Connect the cable. • NO: Go to step 6. Figure 4-2. SPEEDDOME ULTRA SERVICE Pin 1 Pin 1 Pin 1 Pin 1 I/O BOARD JW1 Terminations...
  • Page 53 If none of these steps worked, then send both the dome and its base back to the NRC. To obtain a repair authorization number, call 1-800-543-9740 (CEs) or 1-800-442-2225 (Dealers). If you must perform detailed troubleshooting, use extreme care when disassembling parts! See page 4-5. SPEEDDOME ULTRA SERVICE...

  • Page 54: Dome Functions But Does Not Pan

    CPU board Pan motor Power supply Slot covers Camera Eyeball assembly Camera/Lens board Tilt motor Fragile parts! Once disassembled, parts of the dome housing and eyeball assembly are “extremely fragile” and may break. Proceed using extreme care! SPEEDDOME ULTRA SERVICE...

  • Page 55: How To Remove The Cpu Board

    Remove the three standoffs, then remove the power supply board from the housing. CAUTION—ELECTROSTATIC SENSITIVE DEVICE! Use a grounding strap when handling the board. Reverse steps to reassemble. Figure 4-5. Cable Cable Motor Cable SPEEDDOME ULTRA SERVICE Metal Shield Power Supply Board Slip Ring cable...

  • Page 56: How To Remove The Power Supply Board

    2. Pry off the slot covers (Figure 4-8). Gently pry the slot cover loose, then swivel the eyeball so the remaining slot cover is totally exposed. With the other cover removed, this cover can be easily lifted off. Figure 4-8. SPEEDDOME ULTRA SERVICE...

  • Page 57: How To Remove The Camera

    While pressing the tabs, push up on the eyeball [b] to detach it. Figure 4-11. 4. Detach the slip ring connector (Figure 4-12). Figure 4-12. SPEEDDOME ULTRA SERVICE...

  • Page 58: How To Remove The Camera/Lens Board

    CAUTION—ELECTROSTATIC SENSITIVE DEVICE! Use a grounding strap when handling the board. Reverse steps to reassemble. Figure 4-15. Camera/Lens Board Bearing Assembly SPEEDDOME ULTRA SERVICE Prongs (3) DO NOT unplug cable from J1. J3 (Pins on ribbon cable must face contacts on connector.)

  • Page 59: How To Remove The Tilt Motor

    When putting in a new motor, be careful to properly mesh the motor and tilt gears! Failure to do so can destroy both the motor and tilt gear. Verify that the tilt gear turns freely! SPEEDDOME ULTRA 4-10 SERVICE Tilt Motor (Lift up, then out)

  • Page 60: Dome Maintenance

    Disable line lock Alarm contacts normally open Alarm contacts normally closed 2. Reset the address previously entered. Remove the dome again to set the address previously entered, then reattach it. The dome should then begin its homing routine SPEEDDOME ULTRA 4-11 SERVICE...
  • Page 61 AMERICAN DYNAMICS Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, NY 10965 Technical Support Center 1-800-442-2225 Business (914) 624-7600 SENSORMATIC ELECTRONICS 951 Yamato Road Boca Raton, FL 33431-4425 Technical Support Center 1-800-543-9740 Business (561) 989-7000...

Table of Contents