Juniper M320 Quick Start Manual
  1. Manuals
  2. Brands
  3. Juniper Manuals
  4. Network Router
  5. M320
  6. Quick start manual

Juniper M320 Quick Start Manual

Multiservice edge router
Hide thumbs Also See for M320:
Table of Contents

Advertisement

Quick Links

Download this manual
M320 Multiservice Edge Router
Quick Start
June 2016
Part Number: 530-071202
Revision 1
Contents
Copyright © 2016, Juniper Networks, Inc.
This document describes how to install the Juniper Networks M320 Multiservice Edge
Router.
M320 Quick Start Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 1: Prepare the Site for M320 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
M320 Rack-Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 2: Install the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Install the Four-Post or Cabinet Mounting Hardware . . . . . . . . . . . . . . . . . . . . 6
(Front-Mount Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install Cage Nuts, If Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Install the Small Mounting Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Install the Mounting Hardware in an Open-Frame Rack . . . . . . . . . . . . . . . . . . 9
Install Cage Nuts, If Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install the Large Mounting Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install the Small Mounting Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remove the Mounting Hardware From the Chassis . . . . . . . . . . . . . . . . . . 11
Step 3: Install the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Install the Router Using a Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Install the Installation Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Install the Router Using a Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Install the Router Without a Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Remove Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Lift the Router into the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Reinstall Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Task 4: Connect the Grounding Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Step 5: Connect External Devices and PIC Cables . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connect a Management Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connect to a Network for Out-of-Band Management . . . . . . . . . . . . . . . . . . 20
1

Advertisement

Table of Contents
loading

Related Manuals for Juniper M320

Summary of Contents for Juniper M320

  • Page 1: Table Of Contents

    M320 Quick Start Description ......... . 3 Step 1: Prepare the Site for M320 Installation ......4 M320 Rack-Mounting Requirements .
  • Page 2 M320 Multiservice Edge Router Quick Start Connect the PIC Cables ......... . 20 Step 6: Install Cable Guards and Cable Cover .

  • Page 3: M320 Quick Start Description

    M320 Quick Start Description M320 Quick Start Description This Quick Start contains information you need to install and configure the router quickly. For complete installation instructions, see the M320 Multiservice Edge Router Hardware Guide at http://www.juniper.net/techpubs/hardware/ WARNING: This Quick Start contains a summary of safety warnings in “Safety...

  • Page 4: Step 1: Prepare The Site For M320 Installation

    Step 1: Prepare the Site for M320 Installation M320 Rack-Mounting Requirements on page 4 Tools Required to Unpack and Prepare the M320 Router for Installation on page 5 M320 Rack-Mounting Requirements You can install the router in many types of racks or cabinets.

  • Page 5: Tools Required To Unpack And Prepare The M320 Router For Installation

    Tools Required to Unpack and Prepare the M320 Router for Installation Figure 1: Rack Clearances and Router Dimensions Tools Required to Unpack and Prepare the M320 Router for Installation A mechanical lift – recommended 1/2-in. or 13-mm open-end or socket wrench to remove bracket bolts from the shipping...

  • Page 6: Step 2: Install The Mounting Hardware

    NOTE: To install the adjustable center-mounting hardware for a four-post rack or cabinet, see the M320 Multiservice Edge Router Hardware Guide. To install the front-mounting hardware for a four-post rack or cabinet: Install the Mounting Hardware for a Four-Post Rack or Cabinet (Front-Mount...

  • Page 7: Install The Mounting Hardware For A Four-Post Rack Or Cabinet (Front-Mount Only)

    Large Shelf Spacer Bars Small Shelf 29.51 in. (74.9 cm) 16.86 24.26 in. (61.6 cm) 13.86 U 19.01 in. (48.3 cm) 10.86 U 17.26 in. (43.8 cm) 9.86 U 13.76 in. (34.9 cm) 7.86 U Copyright © 2016, Juniper Networks, Inc.

  • Page 8: Install Cage Nuts, If Needed

    M320 Multiservice Edge Router Quick Start Table 1: Four-Post Rack and Cabinet Mounting Holes (continued) Hole Distance Above “U” Division Large Shelf Spacer Bars Small Shelf 8.51 in. (21.6 cm) 4.86 U 3.26 in. (8.3 cm) 1.86 U 1.51 in. (3.8 cm) .86 U...

  • Page 9: Install The Mounting Hardware In An Open-Frame Rack

    Center-mount: Install the large mounting shelf and small mounting shelf. Figure 3: Center-Mount Hardware Table 2: Open-Frame Rack Mounting Holes Large Small Hole Distance Above “U” Division Shelf Shelf 17.26 in. (43.8 cm) 9.86 U 15.51 in. (39.4 cm) 8.86 U Copyright © 2016, Juniper Networks, Inc.

  • Page 10: Install Cage Nuts, If Needed

    M320 Multiservice Edge Router Quick Start Table 2: Open-Frame Rack Mounting Holes (continued) Large Small Hole Distance Above “U” Division Shelf Shelf 13.76 in. (34.9 cm) 7.86 U 12.01 in. (30.5 cm) 6.86 U 10.26 in. (26.00 cm) 5.86 U 8.51 in.

  • Page 11: Install The Small Mounting Shelf

    Remove the Mounting Hardware From the Chassis If you are front-mounting the router in an open-frame rack, remove the adjustable center-mounting brackets. Remove the screws securing the adjustable center-mounting brackets to the chassis. Remove the adjustable center-mounting brackets. Copyright © 2016, Juniper Networks, Inc.

  • Page 12: Step 3: Install The Router

    M320 Multiservice Edge Router Quick Start Step 3: Install the Router To install the router: Install the Router Using a Mechanical Lift on page 12 Install the Router Without a Mechanical Lift on page 13 Install the Router Using a Mechanical Lift...

  • Page 13: Install The Router Without A Mechanical Lift

    Open-frame rack: Install a mounting screw into each of the open mounting holes aligned with the rack, starting from the bottom. Reinstall the power supplies. See the M320 Multiservice Edge Router Hardware Guide Figure 4: Load the Router onto the Lift...

  • Page 14: Remove Components

    Remove Components NOTE: For complete instructions on removing router components, see the procedures for installing the router without a mechanical lift in the M320 Multiservice Edge Router Hardware Guide. Before lifting the router, you must remove the following components (see...

  • Page 15: Lift The Router Into The Rack

    Lift the Router into the Rack Lifting the chassis and mounting it into a rack requires three people to lift and a fourth person to secure the mounting screws. The empty chassis weighs over 142 lbs (64.7 kg). Copyright © 2016, Juniper Networks, Inc.
  • Page 16 M320 Multiservice Edge Router Quick Start WARNING: Do not lift the router using the installation handle or the handles on top of the chassis. Use these handles only to help position the router. Make sure the rack is in its permanent location and is secured to the building.

  • Page 17: Reinstall Components

    Slide each component into the chassis evenly so that it does not become stuck or damaged. Tighten the captive screws for each component NOTE: Make sure that all empty slots are covered with a blank panel before operating the router. Copyright © 2016, Juniper Networks, Inc.

  • Page 18: Task 4: Connect The Grounding Cable

    M320 Multiservice Edge Router Quick Start Task 4: Connect the Grounding Cable Make sure that grounding surfaces are clean and brought to a bright finish before grounding connections are made. Verify that a licensed electrician has attached the cable lugs provided with the router to the grounding cable.

  • Page 19: Step 5: Connect External Devices And Pic Cables

    Connect a Management Console Locate the appropriate cable and connector. Turn off the power switch on the console. Plug the female end of the RS-232 serial connector into the port on the CONSOLE Connector Interface Panel (CIP). Copyright © 2016, Juniper Networks, Inc.

  • Page 20: Connect To A Network For Out-Of-Band Management

    M320 Multiservice Edge Router Quick Start Plug the other end into the management device. Tighten the screws on the connector. Connect to a Network for Out-of-Band Management NOTE: Before you can use the Ethernet management port to connect to a network for out-of-band management, you must perform the initial Junos OS configuration after the router has been powered on.

  • Page 21: Step 6: Install Cable Guards And Cable Cover

    Partially tighten each of the two captive screws on the cable guard. Tighten each of the two captive screws completely. Repeat Steps 5 through 7 for the other lower cable guard. Copyright © 2016, Juniper Networks, Inc.

  • Page 22: Install The Cable Cover

    M320 Multiservice Edge Router Quick Start Figure 8: Install Cable Guards Install the Cable Cover Insert the upper tabs of the cover into the slots of the upper cable guards. Insert the lower tabs of the cover into the slots of the lower cable guards.
  • Page 23 Install the Cable Cover Figure 9: Install Cable Cover Copyright © 2016, Juniper Networks, Inc.

  • Page 24: Step 7: Providing Power To The Router

    M320 Multiservice Edge Router Quick Start Step 7: Providing Power to the Router Depending on your configuration, the M320 router uses either AC or DC power supplies. Connect AC Power on page 24 Connect DC Power on page 24 Connect AC Power Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
  • Page 25 Turn the circuit breaker for each power supply to the on position ( ) to boot the router. OUTPUT OK LED on the power supply faceplate should blink, then light steadily. Figure 10: Connect Power to a DC Router Copyright © 2016, Juniper Networks, Inc.

  • Page 26: Step 8: Perform Initial Software Configuration

    The M320 Multiservice Edge Router is shipped with the Junos OS preinstalled and ready to be configured when the M320 router is powered on. These procedures connect a router to the network but do not enable it to forward traffic. For complete information about enabling the router to forward traffic, including examples, see the Junos OS configuration guides.

  • Page 27: Configuring System Attributes

    [edit] root# set system backup-router address (Optional) Configure the static routes to remote subnets with access to the management Ethernet port. Access to the management Ethernet port is limited to Copyright © 2016, Juniper Networks, Inc.

  • Page 28: Committing The Configuration

    M320 Multiservice Edge Router Quick Start the local subnet. To access the management Ethernet port from a remote subnet, you must add a static route to that subnet within the routing table. [edit] root# set routing-options static route remote-subnet next-hop destination-IP retain...
  • Page 29 Commit the configuration to activate it, and synchronize the configuration. The commit command commits this new configuration on both Routing Engines synchronize simultaneously. [edit] root# commit synchronize re0: configuration check succeeds re1: Copyright © 2016, Juniper Networks, Inc.
  • Page 30 M320 Multiservice Edge Router Quick Start commit complete re0: commit complete If you receive an error message after you issue the statement, you can review commit the configuration using the command to find the errors in your configuration. show You can delete incorrect entries using the command.

  • Page 31: Safety Warnings

    AC input of the router. Only trained and qualified personnel should install or replace the router. Perform only the procedures described in this quick start or the M320 Multiservice Edge Router Hardware Guide. Other services should be performed by authorized service personnel only.
  • Page 32 ‫ראה הוראות התקנה לפני חיבור הנתב. זהו סיכום של אזהרות בטיחות. לקבלת רשימה‬ :‫אזהרה‬ ‫ אינטרנט מדריך חומרה נתב ב‬M320 ‫מלאה של אזהרות זה הנתב, כולל תרגומים, ראה את‬ . /http://www.juniper.net/techpubs/hardware unexposed ‫ או‬intrabuilding ‫( של הנתב מתאים הקשר‬intrabuilding (S ‫את יציאת‬...
  • Page 33 :‫זהירות‬ .‫רק אנשי צוות מוסמכים שהוכשרו ו צריך להתקין או להחליף את הנתב‬ ‫ אינטרנט מדריך חומרה נתב . שירותים‬M320 ‫רק לבצע את ההליכים המתוארים זה מהיר או להפעיל את‬ .‫אחרים צריך להתבצע על ידי אנשי שירות מוסמכים בלבד‬ .‫קרא את הוראות ההתקנה לפני שאתה לחבר את הנתב אל מקור הכוח‬...
  • Page 34 M320 Multiservice Edge Router Quick Start ‫, וכן שעונים. חפצי‬necklaces ,‫לפני העבודה על ציוד המחובר קווי כוח, להסיר תכשיטים, כולל טבעות‬ ‫מתכת להתחמם כאשר מחובר לשלטון ואת האדמה והוא יכול לגרום כוויות חמורות או מולחם כדי להפוך‬ .‫את מסופי‬ .‫אי לשמור על בטיחות אזהרות אלה עלולים לגרום נזק פיזי רציני‬...

  • Page 35: Compliance Statements For Nebs

    The battery return connection is to be treated as an isolated DC return (i.e. DC-I), as defined in GR-1089-CORE. For Juniper Networks systems with AC power supplies, an external surge protective device (SPD) must be used at the AC power source.

  • Page 36: Japan

    Junos OS Release Notes. ® To obtain the most current version of all Juniper Networks technical documentation, see the product documentation page on the Juniper Networks website at http://www.juniper.net/techpubs/ Requesting Technical Support Technical product support is available through the Juniper Networks Technical Assistance Center (JTAC).

  • Page 37: Self-Help Online Tools And Resources

    7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features: Find CSC offerings: http://www.juniper.net/customers/support/...
  • Page 38 Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.

Table of Contents