11: Preset Memory; 12: Rs-232/Gpi - Roland V-60HD Reference Manual

11: PRESET MEMORY

Menu item Value
LOAD (*16) MEMORY
SAVE (*16) MEMORY
MEMORY
DELETE
This specifies the settings loaded at startup.
START UP LAST MEMORY
MEMORY 1–8
OFF, ON
MEMORY PROTECT
MEMORY LOAD FADE OFF,
(*16) When the [MODE] button is lighted in blue, the AUX/MEMORY buttons function as shortcuts for saving to and loading preset memories.

12: RS-232/GPI

Menu item Value
RS-232
OFF,
BAUDRATE 9600,
PANEL INFORMATION OFF, ON
This sets the function assigned to the GPI channel.
* When a control signal is input from an external source, the assigned function is executed. The GPI trigger is fixed at the
trailing edge (low: ON). For details, refer to "Inputting a Control Signal" (p. 18).
N/A
PGM CH SEL 1–8
PST CH SEL 1–8
MEMORY LOAD 1–8
DSK SRC SEL 1–8
MUTE AUDIO IN 1–5/6
MUTE SDI IN 1–4
GPI 1–8 TYPE
MUTE HDMI IN 5–6
SOLO AUDIO IN 1–5/6
SOLO SDI IN 1–4
SOLO HDMI IN 5, 6
DSK SW
AUTO SW
CUT SW
OUTPUT FADE SW
AUTO MIXING SW
Explanation
(bold text: default value)
1–8 This selects the preset memory to load. Pressing the [VALUE] knob lets you load the preset memory.
This selects a preset memory for saving settings. Pressing the [VALUE] knob lets you save the
settings to the preset memory.
* The state of the [OUTPUT FADE] button and [PHONES] knob are not saved to any preset memory.
The [OUTPUT FADE] button is always dark at startup.
* The state of the [MODE] button and the settings shown below are saved as global settings for
the unit. They are not saved to preset memories.
1–8
Category
RS-232/GPI
LAN CONTROL
SYSTEM
This selects a preset memory to delete. Pressing the [VALUE] knob lets you delete the preset
1–8
memory.
This restores the state that was in effect immediately before the power was turned off (Last
Memory feature).
The current settings (Last Memory values) are saved every 4 seconds, and when you exit a menu.
These recall the settings at the selected memory number.
When this is set to "ON, " the preset memories are protected, and settings cannot be saved to them.
If this is "ON, " fade-to-black is applied when you recall a preset memory.
ON
If this is "OFF, " fade-to-black is not applied when you recall a preset memory. However, the screen
might be disordered depending on the values of the settings that are recalled.
Explanation
(bold text: default value)
ON
Setting this to "ON" makes it possible to send and receive RS-232 commands.
38400 This sets the communication speed (bps) of the RS-232 connector.
When this is set to "ON, " the RS-232 command QPL (7: ALL) is always transmitted, such as when the
channel is switched or when the PGM/A bus and PST/B bus are switched (p. 22).
No function is assigned.
This switches the final output video.
This switches the preset video (the video to be output next).
This loads a preset memory.
During DSK compositing, this switches the channel of the overlaid logo or image.
This turns the input audio mute function on/off.
This turns the input audio solo function on/off.
This performs the same operation as pressing the [DSK] button.
This performs the same operation as pressing the [AUTO] button.
This performs the same operation as pressing the [CUT] button.
This performs the same operation as pressing the [OUTPUT FADE] button.
This performs the same operation as pressing the [AUTO MIXING] button.
Setting items saved in the unit
All menu items
All setting items except "TEST PATTERN" and "TEST TONE"
* "TEST PATTERN" and "TEST TONE" are always set to "OFF" at startup.
Menu List
11