Siemens SITRANS TH100 Operating Instructions Manual page 7

9.3.5 Connection type for input 2 [05] ...................................................................................... 145
9.3.6 Wire resistance for connecting cable at Input 2 [06] ......................................................... 146
9.3.7 Assignment of the primary variable [07]........................................................................... 146
9.3.7.1 Introduction..................................................................................................................... 146
9.3.7.2 Setting the assignment of the primary variable................................................................. 147
9.3.8 Unit [08].......................................................................................................................... 147
9.3.9 Lower range value [09]/Upper range value [10]................................................................ 148
9.3.9.1 Lower range value [09] parameter ................................................................................... 148
9.3.9.2 Upper range value [10] parameter ................................................................................... 148
9.3.9.3 Adjusting lower range value/upper range value ................................................................ 148
9.3.10 Damping value [11] ......................................................................................................... 149
9.3.10.1 Damping value parameter ................................................................................................ 149
9.3.10.2 Set damping value ........................................................................................................... 149
9.3.11 Functional Safety [12]...................................................................................................... 150
9.3.12 Loop test [13] .................................................................................................................. 150
9.3.12.1 Loop test with preset loop current value ........................................................................... 150
9.3.12.2 Loop test with user defined loop current value.................................................................. 151
9.3.13 One-point calibration input 1 [14] .................................................................................... 152
9.3.14 One-point calibration input 2 [15] .................................................................................... 152
9.3.15 Change User PIN [16]....................................................................................................... 152
9.3.15.1 Change user PIN .............................................................................................................. 152
9.3.16 PIN recovery [17] ............................................................................................................. 153
9.3.16.1 Recovering the user PIN ................................................................................................... 154
9.3.17 User PIN [18] ................................................................................................................... 155
9.3.17.1 User PIN........................................................................................................................... 155
9.3.17.2 Enable user PIN................................................................................................................ 155
9.3.17.3 Disable user PIN ............................................................................................................... 155
9.3.18 Minimum measured peak value at Input 1 [19]................................................................. 156
9.3.19 Maximum measured peak value at Input 1 [20] ................................................................ 156
9.3.20 Minimum measured peak value at Input 2 [21]................................................................. 157
9.3.21 Maximum measured peak value at Input 2 [22] ................................................................ 157
9.3.22 Minimum transmitter electronics temperature [23] .......................................................... 157
9.3.23 Maximum transmitter electronics temperature [24].......................................................... 157
9.3.24 Button lock [25]............................................................................................................... 157
9.3.24.1 Enabling button lock ........................................................................................................ 158
9.3.24.2 Disabling button lock ....................................................................................................... 158
9.4 Assigning parameters using remote operation .................................................................. 159
9.4.1 Introduction..................................................................................................................... 159
9.4.2 "Quick Start" wizard ......................................................................................................... 159
9.4.3 Identification ................................................................................................................... 160
9.4.4 User-specific type ............................................................................................................. 160
9.4.4.1 Introduction..................................................................................................................... 160
9.4.4.2 Set the linearization table (60 breakpoints) ...................................................................... 162
9.4.4.3 Set the spline curve (40 breakpoints) ............................................................................... 162
9.4.5 Sensor calibration ............................................................................................................ 162
9.4.5.1 Introduction..................................................................................................................... 162
9.4.5.2 Setting one-point calibration............................................................................................ 163
9.4.5.3 Setting two-point calibration............................................................................................ 164
9.4.6 Transmitter sensor matching ............................................................................................ 165
9.4.6.1 Introduction..................................................................................................................... 165
9.4.6.2 Changing the Callendar-Van Dusen coefficients ................................................................ 166
9.4.7 Assignment of dynamic variables ..................................................................................... 166
SITRANS TH100/TH320/TH420/TR320/TR420/TF320/TF420 with 4 to 20 mA/HART
Operating Instructions, 05/2020, A5E41864807-AB
Table of contents
7