Erdschlussschutz
2
umschaltbar auf I
t-Kennlinie
Die Erdschlussschutzmodule für die Überstromauslöser ETU45B
und ETU76B bieten die Möglichkeit, von einer konstanten Verzöge-
2
rungszeit auf eine I
t-Kennlinie umzuschalten.
Dadurch erhält man eine Auslösekennlinie mit stromabhängiger
Verzögerungszeit bei konstantem I
lagen mit mehreren Staffelebenen eine bessere Selektivität des
Erdschlussschutzes erzielen.
Die Einstellbereiche für die Verzögerungszeit bleiben unverändert.
2
Die Umschaltung auf die I
t
g
- den t
-Drehkodierschalter (ETU45B); diesen auf einen Wert im
g
weiß gekennzeichneten Bereich stellen.
- das Grafikdisplay (ETU76B)
- TD400 und die Software "powerconfig" (ETU76B)
- die COM-Module mit einem PC mit installierter Software
„powerconfig"
→ (Seite 26-3)
- den Modbus RTU mit einem PC und zusätzlicher Software
Erdschlussalarm
→
Erdschlussschutz
Umschaltbare Parametersätze
Der Überstromauslöser ETU76B gestattet die Speicherung von
zwei unterschiedlichen Parametersätzen für die Schutzfunktionen.
Damit ist es möglich, beim Umschalten auf eine andere Einspei-
sung auch anderen Schutzbedürfnissen Rechnung zu tragen.
Die Umschaltung kann erfolgen manuell über:
- das Grafikdisplay
- TD400 und die Software "powerconfig"
- die COM-Module mit einem PC mit installierter Software
„powerconfig"
→ (Seite 26-3)
oder automatisiert über:
- die COM-Module
- den cmit einem Eingangssignal am digitalen Ein-
gangsmodul.
3ZW1012-0WL11-0AB1
2
t
-Wert und kann in Schaltan-
g
-abhängige Kennlinie kann erfolgen über:
(ETU76B)
(Seite 8-67)
Ground-fault protection
2
switchable to I
t characteristic
The ground-fault protection modules for the overcurrent releases
ETU45B and ETU76B offer the possibility to switch over from a con-
2
stant delay time to an I
t-characteristic.
This provides an inverse-time tripping characteristic with a constant
2
I
t
-value, providing better selectivity of the ground-fault protection
g
in system with several grading levels.
The setting options for the delay time remain unchanged.
2
Switchover to the I
t
-characteristic can be made through:
g
- the t
rotary coding switch (ETU45B); this must be set to a value
g
in the white area
- the graphical display (ETU76B)
- TD400 and the software "powerconfig" (ETU76B)
- the COM modules with a PC with the software "powerconfig"
installed
→ (page 26-3)
(ETU76B)
- the Modbus RTU with a PC and additional software
Ground-fault alarm
→
Ground-fault protection
Changeable parameter sets
The overcurrent release ETU76B enables the storage of two diffe-
rent parameter sets for protective functions.
This enables changeover to new protection settings whenever there
is a transfer to another supply source.
Switchover can be made manually through:
- the graphical display
- TD400 and the software "powerconfig"
- the COM modules with a PC with the software "powerconfig"
installed
→ (page 26-3)
or automatically via:
- the COM modules
- the cwith an input signal at the digital input module.
(page 8-67)
8 – 29