1. Manuals
  2. Brands
  3. Eureka Manuals
  4. Floor Machine
  5. RIDER 1201 SH
  6. User manual

Eureka RIDER 1201 SH User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

USER'S MANUAL
RIDER 1201 SH
_______________________________________________
EUREKA S.r.l.
Via dell'Industria 32, 35013 CITTADELLA (PD) ITALY
Fax. ++39 -049 – 9481899
Tel. ++39 - 049 - 9481800
1
INTERNET: www.eurekasweepers.com E-MAIL: info@eurekasweepers.com

Advertisement

Table of Contents
loading

Related Manuals for Eureka RIDER 1201 SH

Summary of Contents for Eureka RIDER 1201 SH

  • Page 1 USER’S MANUAL RIDER 1201 SH _______________________________________________ EUREKA S.r.l. Via dell’Industria 32, 35013 CITTADELLA (PD) ITALY Fax. ++39 -049 – 9481899 Tel. ++39 - 049 - 9481800 INTERNET: www.eurekasweepers.com E-MAIL: info@eurekasweepers.com...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS TOPIC PAGE INTRODUCTION MACHINE DESCRIPTION WARNINGS! GENERAL WARNINGS AND RECCOMANDATIONS DISPOSAL TRASPORT - HANDLING MACHINE DESCRIPTION PRIMARY FUNCTIONS AND CONTROLS USING THE MACHINE SETTING STARTING THE ENGINE FUEL FILLING REPLACING THE FUSES VACUUM CLOSING CONTROL FILTER SHAKER CONTROL SIDE BRUSH CONTROL REPLACING THE SIDE BRUSH EMPTYING THE DIRT CONTAINER...

  • Page 5: Introduction

    INTRODUCTION “EUREKA S.r.l.” , leader manufacturer of sweeping machines, is pleased to welcome you as an owner of the “RIDER 1201 SH” sweeper. We are sure that its use will give you great satisfaction and that while working with the RIDER 1201 SH you will have the opportunity to appreciate its quality, robustness, and versatility.

  • Page 6: Machine Description

    The machine and manufacturer are identified through three plates on the rear of the dirt container REFER TO THESE DETAILS WHEN ORDERING SPARE PARTS OR MAKING ANY OTHER ENQUIRY TO THE MANUFACTURER. EUREKA sweepers conform with the EEC directives and show the CE mark...

  • Page 7: Warnings

    OPERATE, ADJUST, CARRY OUT ORDINARY SERVICING, CLEAN, REPAIR AND TRANSPORT THE MACHINE. EUREKA Srl WILL NOT BE HELD LIABLE FOR ANY PROBLEMS, BREAKAGE, ACCIDENTS OR OTHER OCCURRENCES DUE TO THE IGNORANCE OF OR THE NON-APPLICATION OF THE PROCEDURES CONTAINED IN THIS MANUAL OR TO THE IMPROPER USE OF THE MACHINE.

  • Page 8: General Warnings And Reccomandations

    GENERAL WARNINGS AND RECCOMANDATIONS DANGER SIGNS - ATTENTION THIS SYMBOL HIGHLIGHTS ALL THE OPERATIONS THAT REPRESENT A POTENTIALLY HAZARDOUS SITUATION FOR THE OPERATOR IT IS THEREFORE NECESSARY TO ADHERE CLOSELY TO THE CONDITIONS SHOWN BY THIS SYMBOL DANGER OF BURNING DUE TO VERY HOT SURFACES. EAR PROTECTORS/PLUGS/MUFFLERS MUST BE WORN.
  • Page 9 EMERGENCY SITUATIONS ONLY FIGHT FIRES WITH POWDER FIRE EXTINGUISHERS CLEANING AND MAINTENANCE The machine must be cleaned by persons who have received proper instruction for the purpose, who know how to cut off the sources of energy and who know the characteristics of the machine so as not to find themselves in a hazardous situation.
  • Page 10 PRECAUTIONS FOR THE SAFETY OF OPERATORS AND TECHNICIANS - The machine must not be used by non-authorised personnel who have not been trained to use it properly or by people who are under the influence of substances that could alter their nervous reflexes (alcohol, psycho pharmaceuticals, drugs etc.) - Do not use the machine in inflammable areas or where there is the danger of explosions - Do not collect material that is alight or anything else that could cause a fire.
  • Page 11 UPDATING OF THE USER’S MANUAL When large-scale modifications are made to the machine or new parts are installed, the updated documentation must be sent to the Dealer along with the purchased part or as an update of the manual OBLIGATIONS OF THE EMPLOYER OR OWNER OF THE MACHINE The employer or owner of the machine is responsible for giving the User’s Manual to all the personnel who are going to have to use the machine.

  • Page 12: Disposal

    DISPOSAL SPENT OILS Spent oils must not be thrown away into the environment under any circumstances. They must be given to authorised Collectors in compliance with the regulations currently in force. Temporary storage must be inside watertight containers with sealed lid to avoid contact with the environment and with rainwater.

  • Page 13: Trasport - Handling

    TRANSPORT TRASPORT The machine must be fixed to a pallet to make it easier to transport. Eureka SRL packs the machine by removing the following components: -Steering wheel -Seat -Side brush Before dismounting it, please mount the steering wheel and the seat.
  • Page 14 HANDLING AND TRANSPORT When the machine is moved from one place it is used in to another you are advised to: - not load it on the vehicle with a forklift truck in order not to damage it - lock the machine in place with the parking brake - fix it well to the vehicle using belts, ropes and chains, securing it in the points indicated in the figure.
  • Page 15 TRANSPORTING THE MACHINE BY MANUAL PUSHING DUE TO A FAULT OR TO ENGINE OFF Insert the parking brake Turn anticlockwise the pump unlocking lever (POS. A) completely Sit on the machine and release the parking brake. You can move the sweeper keeping the control of brake and steering After moving the sweeper, turn clockwise the pump unlocking lever (POS.B) completely.
  • Page 17 RIDER 1201 SH BAG FILTER 2. DIRT CONTAINER 3. HYDRAULIC OIL TANK 4. ACCUMULATOR 5. FUEL TANK 6. HYDRAULIC OIL PUMP 7. HYDRAULIC OIL FILTER 8. RH SIDE RUBBER 9. HYDRAULIC OIL BAR 10. FAN 11. OIL MOTOR CAP WITH BAR 12.

  • Page 18: Primary Functions And Controls

    PRIMARY FUNCTIONS AND CONTROLS CONTROLS ON THE MACHINE...
  • Page 19 THROTTLE 2. VACUUM CLOSURE KNOB 3. FILTER SHAKER BUTTON 4. STARTER 5. IGNITION KEY 6. MAIN BRUSH 7. UNLOCKING PUMP KNOB 8. BEEPER DEVICE 9. SEAT ADJUSTMENT LEVER 10. FLAP OPENING LEVER 11. LEFT SIDE BRUSH LEVER 12. RIGHT SIDE BRUSH LEVER 13.

  • Page 20: Main Brush

    SPEED With the lever forward, the engine is at min. (TURTLE POSITION) With the lever back, the engine is at max. (HARE POSITION) VACUUM CLOSING KNOB If the lever is in forward position (DRY) the vacuum is on If the lever is in back position (WET) the vacuum is off FILTER SHAKER BUTTON Press this button for few secons to enable the shaker filter.
  • Page 21 BEEPER SEAT ADJUSTMENT LEVER Pull the lever right to adjust the seat forward or back ---------------------------- FLAP OPENING LEVER Lift the lever to raise the flap to enable the light and big debris collection. LEFT SIDE BRUSH LEVER ------------------------------------- RIGHT SIDE BRUSH LEVER ------------------------------------- BRAKE PEDAL Pressing the pedal, the emergency brake is engaged.

  • Page 22: Using The Machine

    USING THE MACHINE EUREKA SWEEPERS MUST BE OPERATED BY PERSONNEL WHO ARE SUITABLY TRAINED AND AUTHORISED. THE SWEEPERS THAT ARE NOT IN FULL WORKING ORDER MUST BE REMOVED FROM SERVICE. THE SEAT IS FITTED WITH DIPSWITCH THAT PREVENTS IT BEING MOVED FORWARD OR BACK IF THE OPERATOR IS NOT SITTING IN THE DRIVING SEAT.

  • Page 23: Setting

    1. LEFT SIDE BRUSH LEVER (OPTIONAL) 2. BRAKE PEDAL 3. PARCKING BRAKE 4. RIGHT SIDE BRUSH LEVER 5. FORWARD PEDAL 6. MAIN BRUSH LEVER 7. THROTTLE 8. STARTER 9. KEY Before starting the machine, make sure the main brush and the side brushes are raised from the ground.

  • Page 24: Fuel Filling

    1. COFANO MACCHINA 2. ASTA SOLLEVAMENTO COFANO 3. TAPPO SERBATOIO BENZINA Lift the machine hood. FUEL FILLING Block it with the appropriate bar Remove the fuel tank cap and fill up the fuel. (fuel tank capacity: 3.6 lt) CAUTION – Do not go near the machine with lit cigarettes, lighters or matches when you fill up with fuel.

  • Page 25: Replacing The Fuses

    1. STARTER BATTERY BATTERY LIDS CHECKING THE ELECTROLYTE Lift the machine hood. BATTERY LEVEL. Remove the battery lids POS. 2 Check that liquid level is 10 mm over the height of the inner battery’ s plates; close it again Lift the hood and block it by the apposite bar Remove the clamps from the battery.
  • Page 26 VACUUM CLOSING KNOB SHAKER FILTER BUTTON MAIN BRUSH LEVER RIGHT SIDE BRUSH LEVER FRONT FLAP LEVER RIGHT SIDE BRUSH LEVER...

  • Page 27: Vacuum Closing Control

    SHOULD YOU GO ACROSS A WET FLOOR OR A VACUUM CLOSING COURTYARD WITH PUDDLES, YOU MUST CLOSE THE CONTROL VACUUM, SO AS TO PROTECT THE POLYESTER FILTER. With the lever Pos. 1 forward (DRY), the vacuum is on Turn the lever back (WET), the vacuum is off. Pressing the button Pos 2, the filter shaker is activated, this FILTER SHAKER enables the cleaning of the filter...

  • Page 28: Side Brush Control

    1. RIGHT AND LEFT SIDE BRUSH LEVERS 2. FLANGE SCREW 3. FLANGE 4. MAIN SCREW 5. RIGHT AND LEFT SIDE BRUSH Before starting up the brushes, make sure that there are no SIDE BRUSH CONTROL ropes, strings, wire or anything else wound around the brushes The side brush rises and is lowered by working the lever in pos.

  • Page 29: Emptying The Dirt Container

    1. DIRT CONTAINER 2. DIRT CONATAINER WITH REFUSE BOXES KIT (OPTIONAL) After using the machine in dusty areas or with many debris, it is necessarìty to empty the dirt container. EMPTYING THE DIRT CONTAINER To empty it, please proceed as follows: Shake often the filter Turn off the engine and insert the parking brake Hold the dirt container using the handle (A)
  • Page 30 1. MAIN BRUSH 2. MAIN BRUSH LEFT SUPPORT 3. LOCKING BUSH 4. LEFT SIDE DOOR 5. KEY 6. MAIN BRUSH LEVER...

  • Page 31: Main Brush Control

    MAIN BRUSH CONTROL Before starting up the brushes, make sure that there are no ropes, strings, wire or anything else wound around the brushes The side brush rises and is lowered by working the lever in pos. 6: - when the lever is in pos A, the brush is raised and still. - when the lever is pos B, the brush is down and is turning.

  • Page 32: Adjusting The Main Brush

    ADJUSTING THE MAIN Turn off the engine and insert the parking brake. BRUSH Raise the main brush lever Open the left side door and remove the right side. Unloose the fixing screws of the main brush hubs and move them forward. There should be 10 mm from the support. If the brush is worn, move the hubs in the direction of the arrow (forward).

  • Page 33: Replacing The Right Side Rubber Flap

    1. RIGHT PANEL FIXING SCREWS 2. RIGHT PANEL 3. REAR RUBBER FLAP FIXING METAL SHEET 4. REAR RUBBER FLAP 5. RIGHT RUBBER FLAP FRAME FIXING SCREWS 6. RIGHT RUBBER FLAP FIXING METAL SHEET 7. RIGHT RUBBER FLAP Turn off the engine and insert the parking REPLACING THE RIGHT SIDE brake.

  • Page 34: Replacing The Left Side Rubber Flap

    1. RIGHT RUBBER FLAP FIXING METAL SHEET 2. RIGHT RUBBER FLAP 3. FIXING SCREW 4. FIXING LEVER NUT 5. COMPLETE FLAP 6. FRONT RUBBER FLAP FIXING METAL SHEET 7. FRONT RUBBER Turn off the engine and insert the parking REPLACING THE LEFT SIDE brake.

  • Page 35: Replacing The Filter

    FILTER COVER LOCKING BRACKET LOCKING FILTER COVER BAG FILTER SHAKER CONNECTOR SPACERS SHAKER LOCKING PLATES ON RODS FILTER SUPPORT RODS FILTER SUPPORT REPLACING THE FILTER Carefully shake the filter Remove the key Raise the hood and lock it by the bar Remove the filter cover POS.1 Remove the plates POS.2 and the blocking mesh POS.3 Raise the filter and disconnect the connector POS.6...
  • Page 36 1. HYDRAULIC OIL FILTER LID 2. HYDRAULIC OIL FILTER CARTRIDGE 3. OIL LEVEL BAR 4. HYDRAULIC OIL FILTER 5. OIL DRAIN CAP 6. TANK...

  • Page 37: Checking The Hydraulic Oil Level

    CHECKING THE HYDRAULIC OIL LEVEL IN THE TANK Turn off the machine and remove the key EVERY 100 HOURS Extract the dipstick pos. 3 and check that the oil level is in the space where the dipstick is squashed. If it is low remove the cap POS 3 and topp the level up. CAUTION: DIFFERENT FROM THAT ONE INDICATED.
  • Page 38 1. OIL CAP WITH BAR 2. OIL DRAIN HOSE 3. OPENING FOR THE DRAIN HOSE ON THE SIDE 4. TANK...

  • Page 39: Replacing The Engine Oil

    REPLACING THE ENGINE OIL Turn off the machine and remove the key. Open the hood Use a tank for the collection of the used oil. Remove the clamp that blocks the flexible tube POS.2 and pass it on the opening on the left side of the machine (POS 3) Remove the lid from the drain hose POS.2 and let the oil drain in the tank (POS.4).

  • Page 40: Dimensional Drawings

    DIMENSIONAL DRAWINGS...

  • Page 41: Technical Chart

    40 Kg HONDA ENGINE ( RIDER 1201 S ) Model GX200 Rated Power at 3600 RPM 4.1 kW Volts RPM ( Eureka’s adjustment ) 3150/3200 Fuel tank 3,1 Lt. Fuel consumption at 3200 RPM 1,51 Lt\hr Running time RIDER 1201 S with full tank 2 hours Recommended Oil ( tank 0,6 lt.
  • Page 42 OTHER CHARACTERISTICS Drive on front wheel Drum brakes on rear wheels 2 x Rear wheels 3004 ( full rubber, non Ø 250x80 marking ) 1 x Front wheel Rider 1201H x 1: Ø 250x90 non- marking tyre NOISE: HONDA ENGINE Average level of acoustic pressure Lpm=83.58 Db Acoustic power level:...

  • Page 43: Periodic Servicing

    PERIODIC SERVICING REGULAR PERIODIC SERVICING YOUR SWEEPER GUARANTEES OUTSTANDING PERFORMANCE OF THE MACHINE AND ITS LONG LIFE. THE PAGES THAT FOLLOW CONTAIN THE INFORMATION THAT WILL HELP TO PLAN THE CARE AND THE SERVICING THAT THE MACHINE NEEDS. ATTENTION! DO NOT CARRY OUT ANY MAINTENANCE ON THE MACHINE OR ITS COMPONENTS WITHOUT HAVING FIRST TURNED IT OFF, ENGAGED THE HAND BRAKE, BLOCKED THE WHEELS AND DISCONNECTED THE CONNECTOR OF THE TRACTION BATTERY...

  • Page 44: Ordinary Servicing

    EXTRAORDINARY MAINTENANCE AS WELL AS THE SERVICING PROVIDED FOR IN THE SCHEDULED SERVICINGS REFERRED TO BELOW, YOU SHOULD REMEMBER TO: - REPLACE THE HYDRAULIC OIL FILTER CARTRIDGE P/N 680196 AFTER THE FIRST 500 HOURS AND THEN EVERY 1000 HOURS - REPLACE THE HYDRAULIC OIL EVERY 2000 HOURS ORDINARY SERVICING RECOMMENDED SPARE PARTS USED FOR SERVICING.

  • Page 46: Servicing And Maintenance For Scheduled Servicing

    RIDER HONDA SWEEPER SERVICING AND MAINTENANCE 1° SCHEDULED SERVICING MONTH YEAR WORKING AFTER 50 HOURS DATE HOURS Before servicing the machine check carefully if there are fuel, oil or cooling liquid leaks. Open the hood and do the same on the engine ENGINE: ...
  • Page 47 RIDER HONDA SWEEPER SERVICING AND MAINTENANCE 2° SCHEDULED SERVICING MONTH YEAR WORKING AFTER 100 HOURS DATE HOURS Before servicing the machine check carefully if there are fuel, oil or cooling liquid leaks. Open the hood and do the same on the engine ENGINE: ...
  • Page 48 RIDER HONDA SWEEPER SERVICING AND MAINTENANCE 3° SCHEDULED SERVICING MONTH YEAR WORKING AFTER 200 HOURS DATE HOURS Before servicing the machine check carefully if there are fuel, oil or cooling liquid leaks. Open the hood and do the same on the engine ENGINE: ...
  • Page 49 RIDER HONDA SWEEPER SERVICING AND MAINTENANCE 4° SCHEDULED SERVICING MONTH YEAR WORKING AFTER 300 HOURS DATE HOURS Before servicing the machine check carefully if there are fuel, oil or cooling liquid leaks. Open the hood and do the same on the engine ENGINE: ...
  • Page 50 RIDER HONDA SWEEPER SERVICING AND MAINTENANCE 5° SCHEDULED SERVICING MONTH YEAR WORKING AFTER 400 HOURS DATE HOURS Before servicing the machine check carefully if there are fuel, oil or cooling liquid leaks. Open the hood and do the same on the engine ENGINE: ...
  • Page 51 RIDER HONDA SWEEPER SERVICING AND MAINTENANCE 6° SCHEDULED SERVICING MONTH YEAR WORKING AFTER 500 HOURS DATE HOURS Before servicing the machine check carefully if there are fuel, oil or cooling liquid leaks. Open the hood and do the same on the engine ENGINE: ...
  • Page 52 CHECK AND MAINTENANCE SERVICES SWEEPER RIDER HONDA MONTH YEAR WORKING HOURS AT 600 HOURS AS AFTER 100 HOURS DATE SEAL OR STAMP OF THE DEALER THE SCHEDULED SERVICING WAS CARRIED OUT BY CARRYING OUT THE SCHEDULED NAME: _____________________________ SERVICING SURNAME: _____________________________ SIGNATURE:_____________________________ MONTH YEAR...

  • Page 53: Trouble-Shooting Chart

    TROUBLE-SHOOTING CHART WARNING! ANY TYPE OF SERVICE OPERATION OR TEST, WITH THE EXCEPTION OF THOSE SHOWN IN THE ENGINE’S MANUAL OR THE BATTERY’S MANUAL, MUST BE CARRIED OUT BY AUTHORIZED SERVICE CENTRES ONLY. PROBLEM CAUSE SOLUTION With key on, warning lights don’t work Starting battery is flat Charge the battery Fuse is blown...

  • Page 54: Product Warranty

    RIDER SH PRODUCT WARRANTY Eureka Srl warrants that the RIDER SH will be free from defects in material and workmanship for a period of 12 months from date of installation. Written notice of any claimed defect must be given to Eureka Srl or its Authorized Sales/Service Representative within the warranty period and within thirty (30) days after such defect is discovered.

  • Page 55: Installation Form For Warranty Approval

    Warranty claims will be evaluated only if the following Installation Form will be sent by fax or by mail, filled in all its parts, to Eureka’s headquarter within thirty (30) days after the machine’s installation. PLEASE RETAIN THE ORIGINAL COPY WITHIN THE MANUAL COMPANY &...

  • Page 56: Declaration Of Conformity

    ALLEGATO N. A1 DICHIARAZIONE DI CONFORMITA' 2006/42/CEE, 73/23/CEE, 93/68/CEE 89/336/CEE, 92/31/CEE Noi: EUREKA S.r.l. Via dell’Industria 32 35013 CITTADELLA (PD) dichiariamo sotto la nostra esclusiva responsabilità che il prodotto SPAZZATRICE: MODELLO:__________________________________ N°. TELAIO:__________________________________ al quale questa dichiarazione si riferisce è conforme alle seguenti norme: ...

Table of Contents