Konica Minolta AccurioPress C2070 Quick Manual
  1. Manuals
  2. Brands
  3. Konica Minolta Manuals
  4. Printer
  5. AccurioPress C2070
  6. Quick manual

Konica Minolta AccurioPress C2070 Quick Manual

Colour production printing system
Hide thumbs Also See for AccurioPress C2070:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Troubleshooting Manual
AccurioPress
C2070/C2070P/C2060
AccurioPrint C2060L
Quick GuiDE
Colour produCtion printing system

Advertisement

Table of Contents
loading

Related Manuals for Konica Minolta AccurioPress C2070

Summary of Contents for Konica Minolta AccurioPress C2070

  • Page 1 AccurioPress C2070/C2070P/C2060 AccurioPrint C2060L Quick GuiDE Colour produCtion printing system...

  • Page 3: Table Of Contents

    Contents Introduction Welcome ............................1-3 Notations and symbols used in this manual................. 1-3 Intended use of this machine......................1-4 1.3.1 Intended use ............................1-4 1.3.2 Impermissible operating conditions....................1-4 1.3.3 Exclusion of liability..........................1-4 Target groups ..........................1-4 Configuration and Usage of this Guide..................1-5 1.5.1 HTML User's Guide operating environment ..................1-5 1.5.2...
  • Page 4 Installing Applications (Image Controller IC-417/Image Controller IC-313)......4-16 4.4.1 Operating environment ........................4-16 4.4.2 Fiery Utility setup ..........................4-16 4.4.3 In a Windows environment........................4-17 4.4.4 In a Macintosh environment......................4-18 4.4.5 Starting applications .........................4-19 Basic Operations Loading Paper ..........................5-3 5.1.1 Loading paper into the main body tray....................5-3 5.1.2 Loading paper into the Paper Feeder Unit PF-602m................5-5 5.1.3...
  • Page 5 Appendix Good Use of the [HTML User's Guide]..................8-3 Name of each Component ......................8-4 8.2.1 External components ..........................8-4 8.2.2 Internal components ...........................8-7 8.2.3 Control Panel Layout ..........................8-9 Convenient Use of Scan Function (Scan to SMB)..............8-11 8.3.1 Step 1: Prepare the destination computer..................8-12 8.3.2 Step 2: Connect this machine to the network ..................8-13 8.3.3...
  • Page 6 Contents-4 AccurioPress C2070series...

  • Page 7: Introduction

    Introduction...

  • Page 9: Welcome

    Welcome Introduction Welcome Thank you for purchasing this machine. This [Quick Guide] describes basic operations, maintenance, troubleshooting for this machine. This information will be useful to enable the full capabilities of this machine and to utilize such functionality efficiently. Please keep this manual in a safe place where you can access it easily. Notations and symbols used in this manual 7WARNING This symbol indicates that negligence of the instructions may lead to death or serious injury.

  • Page 10: Intended Use Of This Machine

    The user's guides are intended for the following users of the system: Operator: Person who has been trained by Konica Minolta or authorized partner to operate the system for its intended use as well as manage consumables, and perform the maintenance and troubleshooting described in user's guides.

  • Page 11: Configuration And Usage Of This Guide

    Configuration and Usage of this Guide Configuration and Usage of this Guide There are two types of User's Guides for this machine: booklet manuals and User's Guide DVD. When you want to learn about detailed functions or operation procedures, refer to the [HTML User's Guide] included in the User's Guide DVD.

  • Page 12: Conventions Used In This Guide

    1.5.2 Conventions used in this guide This guide describes product names and system configurations as follows. Product name Conventions used in this guide AccurioPress C2070 This machine: Indicates the entire system including options AccurioPress C2070P and functions. AccurioPress C2060 The main body: Indicates the main unit that provides print AccurioPrint C2060L functions in this machine.

  • Page 13: Make A Note About This Machine Information

    Make a Note about This Machine Information Make a Note about This Machine Information 1.6.1 Checking the mounted optional devices Get to know the optional devices mounted on this machine. You can check a part of the mounted optional devices on the [MACHINE] screen of the touch panel. Select the check boxes ( ) of the installed optional devices;...

  • Page 14: Checking Network Information

    Make a Note about This Machine Information 1.6.2 Checking network information Make a note about network information required to use functions of this machine such as printer functions and various applications. To check network information, print out the Configuration Page Print. Printing out the Configuration Page Print (Image Controller IC-603) From the [MACHINE] screen on the touch panel, select [Controller] - [Report Type] - [Network Setting], then press [Execute].
  • Page 15 Make a Note about This Machine Information Printing out the Configuration Page Print (Image Controller IC-417/Image Controller IC-313) From the [MACHINE] screen on the touch panel, select [Controller] - [Tools] tab - [Configuration], then press [Yes]. % Note down the IP address printed on the Configuration Page Print in the entry field according to your environment.
  • Page 16 Make a Note about This Machine Information 1-10 AccurioPress C2070series...

  • Page 17: Before Getting Started

    Before Getting Started...

  • Page 19: Power Supply

    Turning the Power ON/OFF Before Getting Started Turning the Power ON/OFF Power supply This machine has two power switches: main power switch and sub power switch. NOTICE The main power switch is normally kept turned on. The main power switch must be turned on or off only when you start this machine for the first time or when you restart this machine.
  • Page 20 Turning the Power ON/OFF For Image Controller IC-417/Image Controller IC-313, turn the image controller on. % For Image Controller IC-417, turn the power switch in the rear side on ( ), then press the button on the top of the power switch ( % For Image Controller IC-313, turn the power switch in the rear side on (...
  • Page 21 Turning the Power ON/OFF Turning the power off (Image Controller IC-603) Turn off the sub power switch. The touch panel display is cleared, and the Power LED on the control panel is changed from blue to orange. NOTICE While the following message is displayed, do not turn off the main power switch.
  • Page 22 Turning the Power ON/OFF Press [Exit]. NOTICE While the following message is displayed, do not quit the system. Otherwise, a problem such as a toner fixation in the machine may occur. [Cooling in progress / Power is turned off automatically] [Power off in progress / Please do not turn the main power off] After the system has quit, turn off the sub power switch.
  • Page 23 Turning the Power ON/OFF Turning off the power (Image Controller IC-313) Turn off the sub power switch. The touch panel display is cleared, and the Power LED on the control panel is changed from blue to orange. NOTICE While the following message is displayed, do not turn off the main power switch.
  • Page 24 Turning the Power ON/OFF Tips The Image Controller IC-313 can reset Fiery software or restart the entire system as needed. To reset only the Fiery software, press the Menu button on the control panel, then use the row selection button to select [Restart Server] - [Restart Server] in sequence. In this case, do not reboot the Windows operating system.
  • Page 25 Turning the Power ON/OFF Function Description ErP Setting Turns the main power off after the Auto Low Power mode, Auto Shut OFF mode, or the sub power switch is kept in the off state for the specified period of time. There are seven power-saving time periods available: Do Not Switch,12 Hours, 24 Hours, 36 Hours, 48 Hours, 60 Hours, and 72 Hours, from which you can select the desired one.

  • Page 26: Available Operations In This Machine

    Available Operations in this Machine Available Operations in this Machine 2.2.1 Major functions of this machine Print functions This machine can be used as a printing system by installing an optional Image Controller. You can print data on this machine via the printer driver using the application software installed on your com- puter.
  • Page 27 Available Operations in this Machine Scan functions You can send the scan data as an E-mail attachment, send it to a shared computer (SMB server), FTP server, or WebDAV server, and save it to the USB flash drive installed on this machine by mounting an optional Im- age controller.
  • Page 28 Available Operations in this Machine Device control function Image Controller IC-603: PageScope Web Connection PageScope Web Connection is a device control utility program provided by the HTTP server built in the ma- chine. You can access an Image Controller via the network using the Web browser of the computer to check the status of this machine or configure various settings remotely from PageScope Web Connection.

  • Page 29: Application Functions (Image Controller Ic-603)

    Available Operations in this Machine 2.2.2 Application functions (Image Controller IC-603) Color management function (Color Centro) Color Centro is an application that enables efficient color management on your computer. To successfully print in color, you can perform calibration, and edit and manage profiles and replacement tables to adjust colors.

  • Page 30: Application Functions (Image Controller Ic-417/Image Controller Ic-313)

    Available Operations in this Machine 2.2.3 Application functions (Image Controller IC-417/Image Controller IC-313) Fiery Command WorkStation Fiery Command WorkStation is an application that manages jobs and image controller via the network. Job management function The [Job Center] tab provides the functions for the job operator. You can check the job status that is being processed by the controller or that is being printed, and check an overview of the processed job.

  • Page 31: Fiery Hot Folders

    Available Operations in this Machine Imposition function Using Fiery Impose (option), you can impose each page on Fiery Command WorkStation. Printer Delete Utility Printer Delete Utility is an application that is used to completely delete the Fiery printer driver from the com- puter.
  • Page 32 Available Operations in this Machine AccurioPress C2070series 2-16...

  • Page 33: Let's Make Prints

    Let's Make Prints...

  • Page 35: Printing Flow

    Printing Flow Let's Make Prints This chapter describes a basic print workflow using this machine. First confirm the basic flow to print data, then add detailed settings and adjustment to meet your require- ments. Reference For information about application settings of this machine and adjustment procedures, refer to the [HTML Us- er's Guide].

  • Page 36: Step 4: Use The Printer Driver To Print Data

    Printing Flow 3.1.4 Step 4: Use the printer driver to print data Print original data through your computer. Check the application environment of original data in advance. This guide shows a procedure example of how to use Adobe Reader XI in a Windows 7 environment. Click [Print] in the file menu of the application software to display the Print window.

  • Page 37: Installing Software

    Installing Software...

  • Page 39: Installing The Printer Driver (Image Controller Ic-603)

    Installing the Printer Driver (Image Controller IC-603) Installing Software Installing the Printer Driver (Image Controller IC-603) 4.1.1 Operating environment In a Windows environment Item Specifications Operating System Windows Vista, Windows 7, Windows 8.1, Windows 10, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2 Any processor of the same or higher specifications as recommended for your operating system...
  • Page 40 Installing the Printer Driver (Image Controller IC-603) 4.1.3 In a Windows environment Installation Start the installer from the Driver CD/DVD supplied with this machine, then install the printer driver on your computer. This guide describes an example procedure to install the PS Plug-in driver in a Windows 7 environment. For information about how to install another printer driver, refer to the [HTML User's Guide].
  • Page 41 Open the folder that contains the desired printer driver in the Driver CD/DVD. % Select a folder according to the printer driver, operating system, and language to be used. Copy the [AccurioPress C2070 C2060PSxx.pkg] file matching the model name to the desktop, then double-click it.
  • Page 42 If any optional function is mounted, be sure to configure a setting. Select a print command of the application, then select the required printer name from [Print]. Select [AccurioPress C2070/C2060PS] from the pull-down list in the window, then click [Settings]. Click on the upper right corner of the window, then click [Configure] that is displayed.

  • Page 43: In A Windows Environment

    Installing the Printer Driver (Image Controller IC-417/Image Controller IC-313) Installing the Printer Driver (Image Controller IC-417/Image Con- troller IC-313) 4.2.1 Operating environment In a Windows environment Item Specifications Operating System Windows Vista, Windows 7, Windows 8.1, Windows 10, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2 Any processor of the same or higher specifications as recommended for your operating system...

  • Page 44: In A Windows Environment

    Installing the Printer Driver (Image Controller IC-417/Image Controller IC-313) 4.2.3 In a Windows environment Installation Use the Add Printer Wizard to install the printer driver on your computer. This guide describes how to install the driver in a Windows 7 environment. A network setting must be configured on this machine before beginning the installation procedure.

  • Page 45: In A Macintosh Environment

    Installing the Printer Driver (Image Controller IC-417/Image Controller IC-313) When printing a test page, click [Print a test page]. Check the test page printing result. % Then, click [Close]. Select whether to set to a default printer, then click [Finish]. The printer driver is installed.
  • Page 46 Installing the Printer Driver (Image Controller IC-417/Image Controller IC-313) Click [Agree]. Click [Install]. % When the screen for entering [Name] and [Password] is displayed, enter the computer administra- tor's name and password into the respective fields, then click [Install Software]. Select the name of the printer to be installed, then click [Continue].

  • Page 47: Installing Applications (Image Controller Ic-603)

    Installing Applications (Image Controller IC-603) Installing Applications (Image Controller IC-603) 4.3.1 Operating environment Color Centro Item Specifications Operating System Windows Vista, Windows 7, Windows 8.1, Windows 10, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2 Intel Core2 Duo 3 GHz or higher 3 GB or more Memory...

  • Page 48: Color Centro Setup

    Installing Applications (Image Controller IC-603) 4.3.2 Color Centro setup Function overview / Color management Color Centro is an application that enables efficient color management on your computer. Color Centro supports the following seven types of functions. Function Description [Calibration] Enhances accuracy and stability of color printing. You can create data to adjust a color shade by measuring the color printing condition of this machine.
  • Page 49 Utility/Counter - [Administrator Setting] - [Network Setting] - [NIC Settings] The JSP setting is a setting that relates to a connection with a Java application server. Open the Start menu, and then click [All Programs] - [KONICA MINOLTA] - [Color Centro] - [KONICA MINOLTA Color Centro].

  • Page 50: Job Centro Setup

    Installing Applications (Image Controller IC-603) 4.3.3 Job Centro setup Function overview / Job management Using Job Centro, you can manage jobs stored on this machine via a computer. You can also edit jobs and pages with Job Centro. You can change the paper setting or finish setting for jobs saved on this machine, move or delete pages while viewing page thumbnails, or insert a chapter sep- arator.
  • Page 51 Utility/Counter - [Administrator Setting] - [Network Setting] - [NIC Settings] The JSP setting is a setting that relates to a connection with a Java application server. Open the Start menu, and then click [All Programs] - [KONICA MINOLTA] - [Job Centro 2.0] - [KONICA MINOLTA Job Centro 2.0].

  • Page 52: Installing Applications (Image Controller Ic-417/Image Controller Ic-313)

    Installing Applications (Image Controller IC-417/Image Controller IC-313) Installing Applications (Image Controller IC-417/Image Controller IC-313) 4.4.1 Operating environment Fiery Utility Item Specifications Operating System Windows Vista, Windows 7, Windows 8.1, Windows 10, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2 Mac OS X 10.7/10.8/10.9/10.10/10.11 Windows: Pentium4 1GHz or higher ®...

  • Page 53: In A Windows Environment

    Installing Applications (Image Controller IC-417/Image Controller IC-313) 4.4.3 In a Windows environment Installation Start the installer from the User Software DVD supplied with this machine, then install Fiery Utility on your computer. To install, the computer's administrator privilege is required. Insert the User Software DVD into the DVD drive of the computer.

  • Page 54: In A Macintosh Environment

    Installing Applications (Image Controller IC-417/Image Controller IC-313) 4.4.4 In a Macintosh environment Installation Start the installer from the User Software DVD supplied with this machine, then install Fiery Utility on your computer. This guide describes how to install Fiery Command WorkStation. Insert the User Software DVD into the DVD drive of the computer.

  • Page 55: Starting Applications

    Installing Applications (Image Controller IC-417/Image Controller IC-313) 4.4.5 Starting applications Starting Fiery Command WorkStation To start Fiery Command WorkStation, first perform the login procedure. Start Fiery Command WorkStation. % In Windows 7/Vista/Server 2008 R2/Server 2008, open the Start menu, then click [All Programs] - [Fiery] - [Fiery Command WorkStation 5].
  • Page 56 Installing Applications (Image Controller IC-417/Image Controller IC-313) Starting Fiery Hot Folders Start Fiery Hot Folders. Fiery Hot Folders starts, and you can configure hot folders. % In Windows 7/Vista/Server 2008 R2/Server 2008, open the Start menu, then click [All Programs] - [Fiery] - [Fiery Hot Folders].

  • Page 57: Basic Operations

    Basic Operations...

  • Page 59: Loading Paper

    Loading Paper Basic Operations Loading Paper 5.1.1 Loading paper into the main body tray The same paper loading procedure is used for Tray 1 and Tray 2. This section describes how to load paper into Tray 1. Pull out the tray to load paper into. NOTICE Be sure to pull out the tray fully until a blue label shows on the rear-left side of the tray.
  • Page 60 Loading Paper Slide the rear guide plate to any position. % Determine their locations based on the size indicator of the bottom plate of the tray. To fix the side guide plates at the correct locations, load an appropriate amount of paper into the tray while aligning it to the right-hand side of the tray.

  • Page 61: Loading Paper Into The Paper Feeder Unit Pf-602M

    Loading Paper 5.1.2 Loading paper into the Paper Feeder Unit PF-602m The following describes how to load paper into an optional Paper Feeder Unit PF-602m. The same paper loading procedure is used for Tray 3 and Tray 4. Reference For information about how to load paper into other optional paper feeder unit, refer to the [HTML User's Guide].

  • Page 62: Loading Paper In Post Inserter Of Folding Unit Fd-503

    Loading Paper Load the remaining paper into the tray, then press the rear guide plate against the paper. NOTICE Be careful not to load paper above the mark that indicates the height limit on the side guide plate. Otherwise, a paper jam may occur.

  • Page 63: Paper Setting

    Paper Setting Paper Setting 5.2.1 Specifying paper information for a tray Specify the required information (size, type, weight, and other values) for the paper loaded into a paper tray. If standard-size paper is loaded, its size is recognized automatically. To load custom-size paper, specify the required size.
  • Page 64 Paper Setting Press [Paper Size]. Select one of the options under [Size Setting] to fit the paper loaded into the tray. AccurioPress C2070series...
  • Page 65 Paper Setting Specify the size. % [Standard]: Recognized automatically. % In [Detect Size Setting], you can select the size to be detected. % There is, however, a group of sizes having subtle distinctions, so that the machine cannot distin- guish in the operation of size detection. To identify these sizes as one size so that they can be judged by the machine, you can select the size to be detected in [Detect Size Setting].
  • Page 66 Paper Setting % [Tab Paper]: Specify the paper size and the number of tabs. If you select [Detect Size Setting] in [Standard], press [OK]. This returns to the [Size Setting] screen. % This step is not required if you select [Cus- tom] or [Tab Paper].
  • Page 67 Paper Setting Specify other items, if necessary. Press [OK]. This returns to the [Paper Setting] screen. Press [Close]. This returns to the [MACHINE] screen. If you press [Paper Setting] on the [COPY] screen to specify the paper size, the screen re- turns to the [COPY] screen.

  • Page 68: Printer Driver Setting (Image Controller Ic-603)

    Printer Driver Setting (Image Controller IC-603) Printer Driver Setting (Image Controller IC-603) 5.3.1 Printer driver functions This section describes how to specify the color mode using the printer driver. This guide shows a procedure example to make prints using the PS Plug-in driver from Adobe Reader XI in the Windows 7 environment.
  • Page 69 Printer Driver Setting (Image Controller IC-603) [Color Mode]: 2-Color Printing To print process colors (CMYK) using Spot Colors (Special colors), click [Color Mode] in the Printing Prefer- ences window of the printer driver, then specify the colors to be used in [2-Color Printing]. In 2-Color Printing, process colors (CMYK) can be replaced with Spot Colors (Special colors) for printing.
  • Page 70 Printer Driver Setting (Image Controller IC-603) [Management]: Color Configuration The Color Configuration refers to a collection of a profile set available for all paper types and other color set- ting information. You can only specify one Color Configuration at the time of printing to easily apply the color setting available for all paper types.
  • Page 71 Printer Driver Setting (Image Controller IC-603) [Management]: Manual Settings In Manual Settings, manually configure a color conversion setting for printing, for example, specifying an RGB or CMYK color conversion profile, specifying a printer profile appropriate to the required paper type, or se- lecting a Tone Curve.

  • Page 72: Printer Driver Setting (Image Controller Ic-417/Image Controller Ic-313)

    Printer Driver Setting (Image Controller IC-417/Image Controller IC-313) Printer Driver Setting (Image Controller IC-417/Image Controller IC-313) 5.4.1 Printer driver functions This section describes how to specify the color mode using the printer driver. [Color mode]: Select an output color Open [Color] in the Print Setting screen of the printer driver, then select [Color mode] from [CMYK] or [Gray- scale].
  • Page 73 Printer Driver Setting (Image Controller IC-417/Image Controller IC-313) [Color mode]: Basic Settings To specify the basic defaults for color processing, open [Color] in the Printing Preferences window, then click [Basic Settings]. You can also change the setting for each print job. Reference You also select [Color Setup] of Fiery Command WorkStation to configure [Basic Settings] in the color mode.
  • Page 74 Printer Driver Setting (Image Controller IC-417/Image Controller IC-313) [Color mode]: Expert Settings To set defaults to all items for color processing, open [Color] in the Printing Preferences window, then click [Expert Settings]. You can also change the setting for each print job. Reference You can also select [Color Setup] of Fiery Command WorkStation to configure [Expert Settings] in the color mode.

  • Page 75: Maintaining The Finishing Quality

    Maintaining the Finishing Quality...

  • Page 77: Both Sides Adjustment

    Both Sides Adjustment Maintaining the Finishing Quality Both Sides Adjustment 6.1.1 Both Sides Adjustment When performing the duplex printing, you can adjust a misalignment between the front and back sides to align the printing positions on the front and back sides. This task is referred to as Both Sides Adjustment. A heat impact of the fixing unit may cause a slight enlargement or reduction of paper during printing.

  • Page 78: Making The Both Sides Adjustment For Each Tray

    Both Sides Adjustment Making the Both Sides Adjustment for each tray The following adjustment methods are available. % Scan Measurement Adjustment: the method used for adjusting the zoom ratio and printing position of the back side based on those of the front side to match the appearance of the front and back sides.
  • Page 79 Both Sides Adjustment NOTICE Printer model, which is not mounted with a scanner, cannot scan the adjustment charts to perform the [Scan Meas.] adjustment. The [Scan Meas.] adjustment provides the coordination based on the average value of gap amounts, taking into account the gap in printing position between the first and last sheets which can be produced when mul- tiple sheets are output.
  • Page 80 Both Sides Adjustment Check that [Scan Meas.] is displayed, then press [Output Background Sheet]. When the [PRINT MODE] screen is displayed, press Start on the control panel. A background sheet is printed out. % If you already have the background sheet available for measurement, you do not need to print out a background sheet.
  • Page 81 Both Sides Adjustment Enter the number of adjustment charts you want to print out. % You can print out 20 or more adjustment charts; however, only up to 20 adjustment charts can be scan-measured continuously. Press Start on the control panel. Adjustment charts are printed on both sides of the paper in the tray you selected in Step 2.
  • Page 82 Both Sides Adjustment Place an adjustment chart on the Original Glass. % Open the ADF, then place an adjustment chart with the front side facing up (not facing the Original Glass), setting the top side flush with the far end of the glass. Place the upper-left corner of the ad- justment chart approximately 2 inches (approximately 5 cm) away from the vertical size guide and horizontal size guide respectively on the Original Glass making sure that the left and top sides are parallel to the vertical size guide and horizontal size guide respectively.
  • Page 83 Both Sides Adjustment Press [Start] on the [Scan Adjustment Chart] screen. The adjustment chart is scanned. When scanning is properly completed, the counter of [Number of Scanning] on the Scan Adjustment Chart screen is added by one, and the blue frame displayed in the illustration on the screen shifts to the next one on the right side.
  • Page 84 Both Sides Adjustment Repeat the scanning steps 12 to 14 four times for every adjustment chart. % First time: Set the front side of the adjust- ment chart face up (turned away from the original glass), with its top edge positioned to the back side.
  • Page 85 Both Sides Adjustment Select whether to continue the scan measure- ment or to finish the scan measurement and calculate the adjustment value. % To continue the scan measurement, press [No]. To finish the scan measurement and calculate the adjustment value, press [Yes]. % Pressing [No] returns to the [Scan Adjust- ment Chart] screen on which the counter of [Chart Sheets] is added by one.

  • Page 86: Gap Adjustment

    Both Sides Adjustment Gap Adjustment To adjust a gap, print out a chart, measure a gap between the front and back sides at the specified meas- urement point of the back side using a scale to determine the adjustment value, and enter it. (Adjust the zoom ratio and image position of the back side based on the image position of the front side.) Using this function, you can only enter adjustment values to adjust a gap.
  • Page 87 Both Sides Adjustment Select [Gap], then press [Print Mode]. When the [PRINT MODE] screen is displayed, press Start on the control panel. A test chart is printed out. Press [Exit Print Mode]. Measure the gap between the front and back sides at each point of [a] to [d] on the [back] side of the printed out chart.
  • Page 88 Both Sides Adjustment % Write down the measured values so that you do not forget them. Press [a] to [d] of each point, and enter the adjustment value using the keypad, [,], or [+] on the screen. % If the printing position is misaligned to the minus (-) side, enter a positive value (+). If the printing position is misaligned to the plus (+) side, enter a negative value (-).
  • Page 89 Both Sides Adjustment Check a gap of the printing position refering the printed out chart. % Repeat steps 7 to 10 until all gaps between the front and back sides are cleared. Press [Exit Print Mode]. After the adjustment is completed, press [OK]. To finely adjust the adjustment value, continu- ously proceed to step 4 in "Zoom and Image Shift Adjustment"...
  • Page 90 Both Sides Adjustment Chart Adjustment You can print out a Both Sides Adjustment chart, measure measurement points using a scale, and enter measurement values in order to carry out the adjustment. Using this function, you can only enter measurement values to carry out the both-side adjustment. This is convenient when an unclear misalignment is detected between the front and back sides to perform the du- plex printing with a new type of paper or to change paper in a tray.
  • Page 91 Both Sides Adjustment Select [Front], then press [Chart Adjustment]. Press [Print Mode]. When the [PRINT MODE] screen is displayed, press Start on the control panel. A test chart is printed out. Press [Exit Print Mode]. AccurioPress C2070series 6-17...
  • Page 92 Both Sides Adjustment Measure the line length at each of points [1] to [8] on the printed-out chart using a scale. % The figure on the right illustrates an example to measure points [1] and [5]. As illustrated in [ 5 ] [ 1 ] this example, measure the line length at each printed point.
  • Page 93 Both Sides Adjustment When entry processing is completed, press [Adjustment Start]. % In the next step, adjust the back side. Select [Back], then press [Chart Adjustment]. Press [Print Mode]. When the [PRINT MODE] screen is displayed, press Start on the control panel. A test chart is printed out.
  • Page 94 Both Sides Adjustment Press [Exit Print Mode]. Measure a misalignment between the marks of [1] to [4] printed on the [back] side of the output chart and the marks on the [front] side. back % The figure shows an example to measure [1]. The scale resolution is 0.5 mm.
  • Page 95 Both Sides Adjustment Press [X] or [Y] at each point, and enter the measured value using the keypad, [,], or [+] on the screen. % If the printing position is misaligned to the minus (-) side, enter a positive value (+). If the printing position is misaligned to the plus (+) side, enter a negative value (-).
  • Page 96 Both Sides Adjustment Press [Close] to exit the adjustment. Chart Adjustment is then completed. Zoom and Image Shift Adjustment You can finely adjust the zoom ratio of the print side and the top, bottom, left, and right positions on the front and back sides.
  • Page 97 Both Sides Adjustment Press [Both Sides Adj]. Press [Front] or [Back] to select the print side to be adjusted. Enter the zoom ratio or the image shift value using the keypad, [,], or [+] on the screen or the Keypad on the control panel.
  • Page 98 Both Sides Adjustment % To adjust the zoom ratio and image shift, check the status in the center of a page. Zoom ratio adjustment example: The image on the front side is 10 mm in a length- wise direction while the image on the back side has been lengthened to 10.1 mm.
  • Page 99 Both Sides Adjustment After the adjustment is completed, press [OK]. % To register adjustment values in a paper profile, press [Register & OK]. % For details about how to register a paper profile, refer to the [HTML User's Guide]. Press [Close] to exit the adjustment. Zoom and Image Shift Adjustment is then com- pleted.

  • Page 100: Image Quality Adjustment

    Image Quality Adjustment Image Quality Adjustment 6.2.1 Image Quality adjustment Adjust the color image quality at periodic intervals to maintain consistent printing results against a change in ambient temperature or humidity, a change of this machine conditions, or a change of the color tone due to the paper type or print mode.

  • Page 101: Daily Image Quality Management (Calibration)

    Image Quality Adjustment 6.2.2 Daily image quality management (Calibration) You can maintain the color image quality by executing calibration at the appropriate timing. The reference value (target) of the entire printing system is registered in advance. Compare this reference val- ue with the current measurement value to adjust the difference, and correct the printing density.
  • Page 102 Image Quality Adjustment Calibration timing Adjust the daily color image quality at the times and in the order shown below. The adjustment method varies depending on whether or not the Relay Unit RU-509 is installed on the machine. Daily adjustment flow (Standard) This adjustment is required for all customers in daily operations.

  • Page 103: Maximum Density Auto Adjustment (Ru)

    Image Quality Adjustment Order [Menu item] [Description] Without Relay With Relay Unit Unit RU-509 RU-509 STEP3 Calibration [Maximum Density Calibration: (page 6-37) Auto Adjustment Calibrates the color reproducibility that fluctu- (RU)] (page 6-29) or ates from day to day. [Maximum Density Adjustment] [Maximum Density Auto Adjustment (RU)] or (Refer to the [HTML...
  • Page 104 Image Quality Adjustment Press [Quality Adjustment]. Press [Max.Density Auto Adj. (RU)]. Press [Print Mode]. Load the paper that has been used to register the target density into the tray. The paper profile of the tray is automatically switched to the paper profile that has been used to register the target density.
  • Page 105 Image Quality Adjustment Select the tray containing paper, then press [OK]. Press Start on the control panel. A chart applied the Screen 1 (Dot190 Recom- mended) is Output, and auto adjustment is per- formed. When the adjustment is completed, you return to the [Maximum Density Auto Adjustment (RU)] screen.

  • Page 106: Color Density Control

    Image Quality Adjustment 6.2.4 Color Density Control If an optional Relay Unit RU-509 is mounted on this machine, you can configure a setting so that this ma- chine automatically executes calibration at periodic intervals. Calibration is executed every arbitrarily specified number of sheets, and you can keep printing using the ap- propriate density.
  • Page 107 Image Quality Adjustment Press [Basic Setting]. Specify each item as follows: % [Use Color Density Control] ... [ON] % [Periodical Adj. Execution] ... [ON] % [Adjustment Execution Timing] ... [Before Job Start] % [Chart Tray Setting] ... [OFF] Press [Next]. Specify each item as follows: % [Switch Color (1st or 2nd)] ...
  • Page 108 Image Quality Adjustment Press [OK]. Press [Close]. Press [Exit [ADJUSTMENT]]. Automatic Adjustment is set. A chart is printed out periodically, and calibra- tion is carried out automatically. Tips Selecting [Color Density Manual Control] can carry out the manual adjustment. AccurioPress C2070series 6-34...
  • Page 109 Image Quality Adjustment Manual setting of Color Density Manual Control Press [Adjustment] on the [MACHINE] screen. Press [Quality Adjustment]. Press [Color Density Control]. Press [Color Density Manual Control]. % This function is available only when [Use Color Density Control] is set to [ON] in [Color Density Control] - [Basic Setting].
  • Page 110 Image Quality Adjustment Press [Print Mode]. Press [Quality Adj.]. Press [)] of [Screen Pattern] to select a screen. Press [Close]. AccurioPress C2070series 6-36...

  • Page 111: Executing Calibration Using The Image Controller

    Image Quality Adjustment Press Start. A chart is printed out, and calibration is carried out. 6.2.5 Executing calibration using the image controller Using Color Centro (Image Controller IC-603) This guide describes how to carry out calibration for daily maintenance using Color Centro and a colorimeter (FD-5BT).
  • Page 112 Image Quality Adjustment Place the FD-5BT ruler on the chart, while aligning the protrusion of the FD-5BT with the ruler guide. % To use the FD-5BT for measurement, re- move it from the target mask. Carry out the measurement in sequence from row E.
  • Page 113 Image Quality Adjustment Using Fiery Command WorkStation (Image Controller IC-417/Image Control- ler IC-313) This section describes how to carry out calibration for daily maintenance using Fiery Command WorkSta- tion and a colorimeter (EFI Spectrometer ES-1000). Tips This section describes how to carry out calibration when using coated paper as an example. Use a USB cable to connect EFI Spectrometer ES-1000 to your computer.

  • Page 114: Specifying The Reference Image Quality (Image Controller Ic-603)

    Image Quality Adjustment Click [Apply & Close]. The calibrated measurement values are applied. 6.2.6 Specifying the reference image quality (Image Controller IC-603) To stabilize the image quality of this machine, specify the reference values (targets) of the entire printing sys- tem in advance.

  • Page 115: Specifying The Reference Image Quality (Image Controller Ic-417/Image Controller Ic-313)

    Image Quality Adjustment 6.2.7 Specifying the reference image quality (Image Controller IC-417/Image Con- troller IC-313) To stabilize the image quality of this machine, specify the reference values (targets) of the entire printing sys- tem in advance. If you change the setting value in [Custom Screen], hue variations may be drastically changed. If you change the screen, specify the standard image quality following the procedure to avoid hue variations.

  • Page 116: Adjusting The Finisher And Saddle Stitcher

    Adjusting the Finisher and Saddle Stitcher Adjusting the Finisher and Saddle Stitcher 6.3.1 Opening the screen to be adjusted When the finisher or saddle stitcher is mounted on this machine, you can finely adjust various functions such as fold positions or staple positions. Reference For details about how to adjust the finisher, refer to the [HTML User's Guide].
  • Page 117 Adjusting the Finisher and Saddle Stitcher Press the items to be adjusted. % The items displayed on this screen vary depending on the model of the mounted finisher. Adjustable settings The following shows item examples that are displayed on the screen. The items displayed on this screen vary depending on the model of the mounted optional device.
  • Page 118 Adjusting the Finisher and Saddle Stitcher Setting item Description [Fold & Staple Stopper] Adjusts the staple position to reduce the misalignment be- tween the fold and the staples. [Half-Fold Stopper Adj.] Adjusts the half-fold stopper position. [Punch Adjustment] Adjusts punch positions. [Tri-Fold Adjustment] Adjusts tri-folding positions.

  • Page 119: Troubleshooting

    Troubleshooting...

  • Page 121: Replenish And Replace Consumables

    Replenish and Replace Consumables Troubleshooting Replenish and Replace Consumables Replacing a toner bottle 7WARNING Do not throw toner or a container that contains toner (e.g., toner cartridge and developing unit) into an open flame. The hot toner may scatter and cause burns or other damage. 7CAUTION Do not leave toner-related parts (e.g., toner cartridge and developing unit) within easy reach of children.
  • Page 122 Replenish and Replace Consumables NOTICE To replace a toner bottle, check the toner type number indicated on the toner bottle cover. Use of incorrect toner bottles may cause the machine trouble. Press on the upper-right corner of the touch panel or Help on the control panel to display the help message.

  • Page 123: Replacing A Staple Cartridge

    Replenish and Replace Consumables Replacing a staple cartridge If staples run out, the message [Please add staples to the saddle stitcher left side stapler] is displayed on the [MACHINE] screen, and the [Staple Cartridge] indicator changes to yellow in the [Consumable and Scrap In- dicators] display.
  • Page 124 Replenish and Replace Consumables Press the [Add Stapler] tab of the required saddle stitcher, then follow the on-screen instructions to re- place a staple cartridge. % The number on the right-hand side of the help message indicates a replacement procedure. To dis- play the next step, press [,].

  • Page 125: Replacing A Waste Toner Box

    Replenish and Replace Consumables Replacing a waste toner box 7WARNING NEVER throw the waste toner box into a fire. Otherwise, the toner may ignite and cause a dangerous situation. If the waste toner box fills up with waste toner, the message [Waste toner box is full Please replace the box] is displayed on the [MACHINE] screen, and the [Waste Toner Box] indicator changes to yellow in the [Con- sumable and Scrap Indicators] display.
  • Page 126 Replenish and Replace Consumables Press the [Waste Toner] tab, then follow the on-screen instructions to replace the waste toner box. % The number on the right-hand side of the help message indicates a replacement procedure. To dis- play the next step, press [,]. AccurioPress C2070series...

  • Page 127: Clearing Paper Jams

    Clearing Paper Jams Clearing Paper Jams 7.2.1 How to view the animation guide If a paper jam occurs on this machine, the message [Mishandled paper / Please remove paper following the guide] is displayed, and the position of the paper jam is displayed on the screen. Check the paper jam position, then follow the guidance to clear a paper jam.
  • Page 128 Clearing Paper Jams Illustration screen for Jam handling The overview of the method required to clear the jam is displayed on the [JAM Position] screen. Changing to the Illustration screen displays the procedure guidance, so you can clear a paper jam while checking each step.
  • Page 129 Clearing Paper Jams Remove all jammed paper, then press [Close]. This returns to the [MACHINE] screen. Tips If the paper jam message has not been yet cleared even after all the jammed paper has been removed, the paper jam may have occurred in a place other than the one displayed. Check other places not dis- played on the touch panel again.

  • Page 130: If The Specified Paper Is Not Found

    If the Specified Paper is not Found If the Specified Paper is not Found If the specified paper is not loaded into a tray at the time of printing, the message [Please load designated xxx paper / To check details, touch [Confirm Details]] is displayed on the screen. To address this problem, load the specified paper into a tray, or you can forcibly print on the currently loaded paper of a different size.
  • Page 131 If the Specified Paper is not Found Replace paper into the tray, then press [Close]. Press Start on the control panel. Printing starts using the selected tray. AccurioPress C2070series 7-13...
  • Page 132 If the Specified Paper is not Found Forcibly printing using the loaded paper Press [Confirm Details] on the [MACHINE] screen. Select a tray with print paper loaded, then press [Forced Output]. Press Start on the control panel. Printing starts using the selected tray. AccurioPress C2070series 7-14...
  • Page 133 If the Specified Paper is not Found If using Image Controller IC-417/Image Controller IC-313 Press [Controller] on the [MACHINE] screen. Press [Login]. Select [Administrator] or [Operator], enter the password, then press [Login]. % If you select [Operator], you do not need to enter the password. Select the print job.

  • Page 134: If An Error Has Been Displayed During Scanning

    If an Error has been Displayed during Scanning If an Error has been Displayed during Scanning If you cannot send data, [Error] is displayed in [Send History] on the [JOB LIST] screen. Check the free space on the HDD (image controller area). Start the Web browser.

  • Page 135: Hue Adjustment

    Hue Adjustment Hue Adjustment Various problems, for example, the current hue is different from the previous one or the expected chromog- enic effect has not been obtained, are caused due to a change in ambient temperature or humidity, a change of the machine conditions, or a change of the color tone by the paper type or print mode.
  • Page 136 If you forget the administrator password AccurioPress C2070series 7-18...

  • Page 137: Appendix

    Appendix...

  • Page 139: Good Use Of The [Html User's Guide]

    Good Use of the [HTML User's Guide] Appendix Good Use of the [HTML User's Guide] The [HTML User's Guide] is included in the User's Guide DVD supplied with this machine. Select the desired item on the top page (Home), then check the detailed contents. To view the details about how to use the [HTML User's Guide], select [User's Guides] on the top page (Home).

  • Page 140: Name Of Each Component

    Name of each Component Name of each Component 8.2.1 External components Name Description ADF (Option) Scans data while automatically feeding an original page by page. Even a 2-sided original can be scanned by one pa- per feed operation without reversing paper. This device cannot be installed on the Printer model.
  • Page 141 Name of each Component Name Description Dust proof filter A dust proof filter is installed in the built-in cooling fan to keep out dust. Power cord Supplies this machine with electricity. Image Controller IC-603 This is the installation position when Image Controller IC-603 is equipped.
  • Page 142 Name of each Component Name Description Down button Scrolls the screen downward. Menu button Display the menu screen. Up button Scrolls the screen upward. Control panel Restarts Image Controller IC-313, displays its IP address, and carries out reboot processing. AccurioPress C2070series...

  • Page 143: Internal Components

    Name of each Component 8.2.2 Internal components Name Description Main power switch Turns the main power of the machine on or off. The main power is basically turned on or off by your service representative. Be sure not to turn the main power switch off in usual operation.
  • Page 144 Name of each Component Name Description Lever [M1] Locks the conveyance fixing unit. If a paper jam has been detected, push this lever down to the left and pull out the conveyance fixing unit. Fixing unit Fuses toner on paper by heat and pressure. Side guide lock knobs Fixes the side guide plates.

  • Page 145: Control Panel Layout

    Name of each Component 8.2.3 Control Panel Layout Name Description Keypad Enter the values such as the number of copies or the zoom ratio. Reset* Returns the contents you entered or changed on the con- trol panel to the default settings. Power LED Lights up in orange when the main power switch is turned on, then lights up in blue when the sub power switch is...
  • Page 146 Name of each Component Name Description Start LED Indicates the status of this machine with LED colors. • Light up in blue: This machine is ready to start opera- tions. • Light up in orange: This machine is not ready to start operations.

  • Page 147: Convenient Use Of Scan Function (Scan To Smb)

    Convenient Use of Scan Function (Scan to SMB) 7CAUTION Stop the operation immediately when the Service Call Screen is displayed and output cannot be con- tinued any more. Otherwise, an unexpected trouble may be caused. Write down the report code as stated on the 2nd line of the message, turn off the sub power switch and main power switch in this order, then disconnect from the power socket.

  • Page 148: Step 1: Prepare The Destination Computer

    Convenient Use of Scan Function (Scan to SMB) 8.3.1 Step 1: Prepare the destination computer In Step 1, execute the following tasks: To check the destination computer name and accessible user name. To create a folder on the destination computer and to configure a sharing setting. In a Windows environment Tips To carry out this task, the computer's administrator privilege is required.

  • Page 149: Step 2: Connect This Machine To The Network

    Convenient Use of Scan Function (Scan to SMB) In a Macintosh environment Tips To carry out this task, the computer's administrator privilege is required. Select [About This Mac] - [More Info] to check [IP Addresses] and [User name]. Enable file sharing. % In the Apple menu, click [System Preferences] - [Sharing] to open the [Sharing] window, then select the [File Sharing] check box.

  • Page 150: Step 5: Send Scan Data To A Public Folder

    Convenient Use of Scan Function (Scan to SMB) 8.3.5 Step 5: Send scan data to a public folder Send scan data to a public folder of the registered SMB server. In the [SCAN] screen of this machine, select an SMB destination, configure the scan conditions, then press Start.

  • Page 151: Major Specifications

    Major Specifications Major Specifications NOTICE The specifications of the machine and optional device are subject to a change without notice. Even if the specified paper size and weight are compatible with an optional device, if they are not supported by the entire system including the machine, the paper may not be able to be used. Some optional devices are not supported in certain regions.

  • Page 152: Feeding-Related Optional Devices

    Major Specifications 8.4.2 Feeding-related optional devices Reference The paper size and weight vary depending on conditions such as setting or finishing. For details about the detailed conditions or specifications, refer to the [HTML User's Guide]. Paper Feeder Unit PF-602m Paper tray 1: Tray 3 (upper tray) 2: Tray 4 (lower tray) Specifications...
  • Page 153 Major Specifications Paper Feeder Unit PF-707 Paper tray 1: Tray 3 (upper tray) 2: Tray 4 (middle tray) 3: Tray 5 (lower tray) Specifications Paper weight 55 g/m to 350 g/m / 13 lb Bond to 93 lb Bond • Coated paper: 81 g/m to 300 g/m / 22 lb Bond to 81 lb Bond...
  • Page 154 Major Specifications Large Capacity Unit LU-202m Paper tray Specifications Paper weight 64 g/m to 300 g/m / 17 lb Bond to 81 lb Bond • Coated paper: 81 g/m to 300 g/m / 22 lb Bond to 81 lb Bond SRA3 w, A3 w, B4 w, SRA4 w/v, A4 w/v, B5 v, Paper size •...
  • Page 155 Major Specifications Multi Bypass Tray MB-506 Paper tray 1: Multi Bypass Tray Specifications Paper weight 62 g/m to 300 g/m / 16 lb Bond to 81 lb Bond Paper size • SRA3 w, A3 w, B4 w, SRA4 w/v, A4 w/v, B5 w/v, A5 w/v, B6 w, A6 w, 13 e 19 w, 12 e 18 w, 11 e 17 w, 9 e 11 v, 8.5 e 14 w, 8.5 e 11 w/v, 5.5 e 8.5 w, 8K w, 16K w/v, Foolscap* •...
  • Page 156 Major Specifications Post Inserter (Folding Unit FD-503) You can load paper into the upper and lower trays of Folding Unit FD-503 and feed paper to an output-re- lated optional device. On the control panel of the post inserter, you can configure the punch or fold function for paper to be fed from the lower tray.
  • Page 157 Major Specifications Post Inserter PI-502 To use Post Inserter PI-502, mount it in one of Finisher FS-531/FS-532/FS-612. You can load paper into the upper and lower trays of Post Inserter PI-502 and feed paper to an output-related optional device. On the control panel of Post Inserter PI-502, you can configure the punch, staple, or fold function for paper to be fed from the lower tray (the configurable function varies depending on finisher models).

  • Page 158: Output-Related Optional Devices

    Major Specifications 8.4.3 Output-related optional devices Reference The paper size and weight vary depending on conditions such as setting or finishing. For details about the detailed conditions or specifications, refer to the [HTML User's Guide]. Relay Unit RU-509 Conveyance Unit Specifications Function •...
  • Page 159 Major Specifications Relay Unit RU-510 Conveyance Unit Specifications Function • Multi reversed paper conveyance • Reversed paper conveyance • Straight delivery Paper weight 40 g/m to 350 g/m / 11 lb Bond to 93 lb Bond SRA3 w, A3 w, B4 w, SRA4 w/v, A4 w/v, B5 w/v, A5 w/v, A6 w, Paper size •...
  • Page 160 Major Specifications Folding Unit FD-503 Output tray Function Half-Fold Tri-Fold-in Tri-Fold-out Z-Fold Gate Double Parallel Punch 1: Primary (main) tray 2: Multi folder tray Specifications: Straight delivery Paper weight 40 g/m to 350 g/m / 11 lb Bond to 93 lb Bond Paper size Primary (main) tray •...
  • Page 161 Major Specifications Specifications: Punch Number of punch holes • Metric area: 2 holes/4 holes • Inch area: 2 holes/3 holes Hole diameter 6.5 ± 0.5 mm / 0.26" (2 holes/4 holes), 8.0 ± 0.5 mm / 0.31" (3 holes) Hole pitch •...

  • Page 162: Saddle Stitcher Sd

    Major Specifications Saddle Stitcher SD-506 Output tray Function Fold & Staple Multi Half-Fold Multi Tri-Fold Multi Half-Fold + Trimming Specifications: Fold & Staple Paper weight 50 g/m to 244 g/m / 13 lb Bond to 65 lb Bond SRA3 w, A3 w, B4 w, SRA4 w, A4 w, B5 w, Paper size •...
  • Page 163 Major Specifications Specifications: Trim Paper weight 50 g/m to 244 g/m / 13 lb Bond to 65 lb Bond SRA3 w, A3 w, B4 w, SRA4 w, A4 w, B5 w, 12 e 18 w, Paper size • 11 e 17 w, 8.5 e 14 w, 8.5 e 11 w, 7.25 e 10.5 w, 8K w, 16K w, Fools- cap* •...
  • Page 164 Major Specifications Specifications: Multi Half-Fold, Multi Tri-Fold Paper weight Multi Half-Fold: 50 g/m to 300 g/m / 13 lb Bond to 81 lb Bond Multi Tri-Fold: 50 g/m to 91 g/m / 13 lb Bond to 24 lb Bond Tri-Fold with crease (Multi-Fold released): 106 g/m to 216 g/m / 29 lb Bond 57 lb Bond...
  • Page 165 Major Specifications Specifications: 2-Side Slitting Paper weight 50 g/m to 350 g/m / 13 lb Bond to 93 lb Bond Paper size Fold & Staple / Half-Fold / Straight output / Sub tray output • SRA3 w, A3 w, B4 w, SRA4 w, A4 w, B5 w, 12 e 18 w, 11 e 17 w, 8.5 e 14 w, 8.5 e 11 w, 7.25 e 10.5 w, 8K w, 16K w, Fools- cap* •...
  • Page 166 Major Specifications Perfect Binder PB-503 Output tray Function Perfect binding Specifications Paper weight Perfect binder tray • Body set: 62 g/m to 105 g/m / 16 lb Bond to 28 lb Bond • Cover: 81 g/m to 216 g/m / 22 lb Bond to 57 lb Bond Secondary (sub) tray •...
  • Page 167 Major Specifications Finisher FS-531 To use the punch function, the Punch Kit PK-512 or Punch Kit PK-513 is required. Output tray Function Staple Punch 1: Primary (main) tray 2: Secondary (sub) tray Specifications: Straight delivery Paper weight 60 g/m to 350 g/m / 16 lb Bond to 93 lb Bond Paper size Primary (main) tray...
  • Page 168 Major Specifications Specifications: Staple Paper weight 60 g/m to 209 g/m / 15 lb Bond to 56 lb Bond A3 w, B4 w, SRA4 w, A4 w/v, B5 w/v, A5 v, Paper size • 11 e 17 w, 8.5 e 14 w, 8.5 e 11 w/v, 7.25 e 10.5 w/v, 5.5 e 8.5 v, 8K w, 16K w/v, Foolscap* Tab Paper: A4T v, 8.5 e 11T v •...
  • Page 169 Major Specifications Finisher FS-532 To use the punch function, the Punch Kit PK-522 is required. Saddle Stitcher SD-510 is required to use the Multi Half-Fold, Multi Tri-Fold, and Fold & Staple functions. Output tray Function Staple Punch Multi Half-Fold Multi Tri-Fold Fold &...
  • Page 170 Major Specifications Specifications: Staple Paper weight 50 g/m to 300 g/m / 13 lb Bond to 93 lb Bond SRA3 w, A3 w, B4 w, SRA4 w/v, A4 w/v, B5 v, A5 v, Paper size • 13 e 19 w, 12 e 18 w, 11 e 17 w, 9 e 11 v, 8.5 e 14 w, 8.5 e 11 w/v, 7.25 e 10.5 v, 5.5 e 8.5 v, 8K w, 16K v, Foolscap* Tab Paper: A4T v, 8.5 e 11T v •...
  • Page 171 Major Specifications Specifications: Staple Maximum number of sta- Paper Plain Fine Others pled sheets: weight Length: Length: Length: Length Length: Length Less : 321 to :148m than mm / mm / mm / 15.75" 12.59" mm / 15.71" 5.83" mm / or more or less 12.6"...
  • Page 172 Major Specifications Specifications: Staple Number of stored copies • 150 sets (2 to 9 sheets stapled, Paper length: 182 mm to 364 mm / 7" to 14" • 75 sets (2 to 9 sheets stapled, Paper length: Other than 182 mm to 364 mm / 7"...
  • Page 173 Major Specifications Specifications: Multi Half-Fold / Multi Tri-Fold (with Saddle Stitcher SD-510 mounted) Sheet volume Maximum number of multiple sheets • Multi Half-Fold 50 g/m to 216 g/m / 13 lb Bond to 57 lb Bond: 5 sheets 217 g/m to 300 g/m / 58 lb Bond to 81 lb Bond: 1 sheets •...
  • Page 174 Major Specifications Specifications: Staple Paper weight 60 g/m to 105 g/m / 16 lb Bond to 28 lb Bond A3 w, B4 w, SRA4 w, A4 w/v, B5 w/v, A5 v, Paper size • 12 e 18 w, 11 e 17 w, 9 e 11 v, 8.5 e 14 w, 8.5 e 11 w/v, 7.25 e 10.5 w/v, 5.5 e 8.5 v, 8K w, 16K w/v, Foolscap* Tab Paper: A4T v, 8.5 e 11T v •...
  • Page 175 Major Specifications Specifications: Half-Fold / Tri-Fold Sheet volume • Number of sheets folded in Multi Half-Fold: 3 sheets (60 g/m 105 g/m / 16 lb Bond to 28 lb Bond) • Number of loadable sheets in Multi Half-Fold: Approx. 33 sets, each of which consists of three sheets folded in Multi Half-Fold (Approx.
  • Page 176 Major Specifications Auto Ring Binder GP-502 Binder Unit Function Bind Specifications Paper weight Body: 75 g/m to 120 g/m / 20 lb Bond to 32 lb BondCover: 163 g/m 216 g/m / 44 lb Bond to 57 lb BondTabbed paper: 163 g/m max.

  • Page 177: Feeding And Output-Related Optional Device

    Major Specifications 8.4.4 Feeding and output-related optional device Banner Tray Unit MK-740 Feeding extension tray, Output extension tray 1: Feeding extension tray 2: Output extension tray Specifications Applicable Feeding ex- Multi Bypass Tray MB-506 unit tension tray Output exten- Output Tray OT-510 sion tray Output Tray OT-511 Finisher FS-531...

  • Page 178: Electronic Optional Devices

    Major Specifications 8.4.5 Electronic optional devices Reference For information about optional devices not described below, refer to the [HTML User's Guide]. Image Controller IC-603 Specifications Function Built-in image controller Capacity • HDD capacity: 200 GB or more (The HDD in the main body is used par- tially.) •...

  • Page 179: Original-Related Optional Devices

    Major Specifications 8.4.6 Original-related optional devices Dual Scan Document Feeder DF-706 This device does not support the Printer model. Document Feeder Specifications Function • Simplex original feeding • Duplex original feeding Original type • Simplex original: 35 g/m to 210 g/m / 10 lb Bond to 57 lb Bond (35 g/m to 49 g/m...

  • Page 180: Weight For Each Size And Copying Speed

    Weight for each size and copying speed Weight for each size and copying speed NOTICE The product specifications are subject to a change without notice. Weight for each size The paper weight (g/m / lb Bond) or ream weight (kg) unit is used to indicate the paper thickness, which varies depending on the manufacturer.
  • Page 181 For information about copying speeds that vary depending on the temperature or settings, refer to the fol- lowing list. Reference For details about [Weight], [Expert Adjustment] and [Glossy], refer to the [HTML User's Guide]. AccurioPress C2070/AccurioPress C2070P Temperature de- Paper weight 1-minute copying speed (at 1-sided output with plain pa- per A4 v / 8.5 e 11 v)
  • Page 182 Weight for each size and copying speed AccurioPress C2060/AccurioPrint C2060L Temperature de- Paper weight 1-minute copying speed (at 1-sided output with plain pa- tected by Humid- (g/m / lb Bond) per A4 v / 8.5 e 11 v) ity/Temperature Normal setting When [Glossy] is selected Sensor 61 pages (A4 v)

  • Page 183: Maximum Paper Size And Printing Area

    Maximum paper size and printing area Maximum paper size and printing area The maximum paper size and printing area that are available are as follows. Refer them when you output data or perform an imposition printing. When using the Tray 2 (Main body lower tray): 487.7 mm / 19.20"...
  • Page 184 Maximum paper size and printing area AccurioPress C2070series 8-48...

This manual is also suitable for:

Accuriopress c2070pAccuriopress c2060Accurioprint c2060l

Table of Contents