Summary of Contents for Konica Minolta bizhub C253
Page 1
INSTALLATION MANUAL Applied Machines: <Important> Be sure to correctly follow the procedures in order as explained in this installation manual. If you do not follow the procedure in order, the image trouble may occur. I. Outline of installation procedures PC-104 PC-204 PC-405 DK-504...
V. Removing the machine VI. Removing protective tape, packing and other shipping materials 1. Open the shipping carton and remove the IU car- ton and machine carton. 1. Remove protective tape from different parts of the 2. Pull out the handles. machine.
Page 4
3. Remove the protective sheet. 7. Pull the lever and raise the control panel until the indention shown in the illustration is placed in a horizontal position. Indentation Horizontal A02EIXC015DA 4. Slide out the 1st drawer and remove protective tape from the inside of the drawer. A02EIXC019DB 8.
Page 5
VII. Installing the IU 10. Place the control panel cable into the cover A furnished with the machine. Secure the cover 1. Open the front door. with screws (three screw A’s furnished with the machine). A02EIXC023DA A02EIXC022DB 2. Tilt the IU to the left and, in that condition, shake it over a small stroke twice.
VIII. Installing the toner cartridge 4. Keeping the IU in the level position, insert it all the way as far as it will go. Note: Note: Since cartridge is not furnished with the machine, • Make sure that the color is same between purchase toner cartridge (of different colors) sepa- inserting port and the IU.
Page 7
IX. Connecting the power cord and 3. Push the toner cartridge all the way in. Note: mounting the accessory parts Make sure that the toner cartridge is pushed all the 1. Connect the power cord. way in. A02EIXE096DA A02EIXC031DA 2. Fit the cord clamp furnished with the machine 4.
Page 8
X. Installing the user’s guide holder 4. Attach the cap A and B furnished with the machine. Install the user’s guide holder. A02EIXC033DA A02EIXC037DA 5. Attach the connector cover furnished with the machine. XI. Mounting the original cover Install the original cover. A02EIXC034DA 6.
Page 9
XIII. Adjusting touch panel XIV. Setting gradation adjust 1. Turn ON the Main Power Switch and then Sub 1. Set that A3 or Ledger paper is loaded in Power Switch. the tray. 2. Press the accessibility key. 2. Display the Service Mode screen. 3.
Page 10
7. Place the test pattern face down on the original 13. Place the test pattern face down on the original glass. glass. A02EIXC041DA A02EIXC043DA 8. Place about ten sheets of A3 or Ledger 14. Place about ten sheets of A3 or Ledger paper on the test pattern placed on the original paper on the test pattern placed on the original...
XV. Date/Time setting 19. Place the test pattern face down on the original glass. 1. Make sure that the Service Mode screen is dis- played. 2. Display the Date & Time Setting screen. (To display the Date & Time Setting screen, press Stop →...
XVI. Install date XVIII. Unit change 1. Display the Service Mode screen. Note: (For details of how to display the Service Mode This function allows the user to select the type of screen, see the service manual.) message that will appear when the replacement 2.
XIX. List Output XX. Affixing the paper size label Affix the paper size label. 1. Load the tray 1 with A4 or Letter paper. 2. Touch “List Output.” 3. Touch the “Machine Management List” and press the start key. The list will be output. 4.
Page 14
XXII. Adjusting registration of paper 7. Select the function to be used as follows: Centering (Duplex 2nd side) → 3rd. source options 8. Press the start key. A test print will be produced. <1 way paper feed cabinet, large capacity cabinet> 1.
Page 15
<2 way paper feed cabinet> 7. Select the function to be used as follows: Centering (Duplex 2nd side) → 3rd. 1. Display the Service Mode screen. (For details of how to display the Service Mode 8. Press the start key. screen, see the service manual.) A test print will be produced.
XXIII. Check through test print XXV. Network setting Make operation checks using “Setting Information Make the TCP/IP address setting for the network. Print.” Note: 1. Select the function to be used as follows: Consult the network administrator for the setting Utility/Counter →...
Page 17
WT-502 Working Table INSTALLATION MANUAL I. Accessory parts II. Installing the working table 1. Using nippers, pull out the knockouts (at two Name Shape Q’ty places) from the right side surface of the 1. Working table machine. A07EIXC001DA 2. Screw (4 ×...