Standard Connection Diagram; Standard Connection Diagram; Class: 2 Kv - YASKAWA FSDrive-MV1000 Instructions Manual

3.2

Standard Connection Diagram

The standard connection diagram for the drive is shown below. For the operating method, see
Operation on page 77.
NOTICE: Consider voltage tolerance levels and insulation in applications with a high input voltage or particularly long wiring distances.
Contact your Yaskawa representative or the nearest Yaskawa sales office.

◆ Class: 2 kV

Figure 3.1
Main circuit input
terminals
Main circuit power supply,
AC 3-phase
R
2.4 kV
S
60 Hz
T
Ground resistance:
less than 10 Ω
Control power supply
terminals
Control power supply,
AC single-phase
R
200/220 V
S
50/60 Hz
Ground resistance:
less than 100 Ω
Analog input terminals
Frequency reference
4 to 20 mA DC
Sequence input
terminals
Run
Stop
command
command
E
E
Medium-voltage
primary panel on
Operation interlock
Reserved
External fault
reset
Reserved
Sequence output
terminals
Major fault
During run
Drive ready
Minor fault
Medium-voltage
power shutdown
command
Figure 3.1 Drive Standard Connection Diagram (Example: CIMR-MV2 A6AA052)
YASKAWA ELECTRIC EZZ010928 FSDrive-MV1000 Instructions
R
S
T
Grounding of the
main circuit
terminal EA
(Option)
Cooling fan power supply
Controller power supply
ISO
RC
AMP
SC
Grounding of the
control system CN4-2 CN21, 22
terminal ED Input voltage Input current
Current detection
resistance board
Analog input: 2 points
-10 V to +10 V
L1 AI_1
1
L2 GND
ISO 2
AMP
L3 FG
3
1
2
(Option)
3
200/220 Vac
Digital input: 8 points
13
14
15
1
I/O
2
3
4
5
6
7
8
9
10
Output
(transfer
contact)
30
32
31
33
35
34
36
38
37
39
40
41
42
Digital output: 8 points
Relay circuit
Digital input: 8 points
Relay
board
Digital output: 8 points
(option)

3.2 Standard Connection Diagram

ISO
AMP
CN4-1
RJ-45
Output
voltage
RS-232
Panel board
USB
RS-485
From expansion PLC board
Relay circuit
DO
DI
Analog output: 4 points
-10 V to +10 V
AO_1
1
GND ISO
2
AMP
FG
3
AO_2
1
GND
2 ISO
FG AMP
3
1
2
(Option)
3
1
2
(Option) 3
Expansion PLC
board (option)
215IF
or
218IF
(Ethernet)
To panel board
RS-232
I/O or communication
board (option)
Line driver PG board
(option)
Phase-A/B/Z input
Complementary PG
board (option)
Phase-A/B/Z input
Start-Up Programming &
Main circuit output
terminals
U
V M
W
2.4kV
Digital operator
RJ-45
USB copy unit (option)
USB
RS-232
DriveWizard Plus MV
Terminals for inrush current
26
suppression circuit (option)
27
MC ON
28
L47
L48 MC ANS
Analog output
terminals
L4
Output frequency
L5
L6 4 to 20 mA DC
L7
L8 Output current
L9 4 to 20 mA DC
Either one or two boards can be
installed by setting parameter.
Line driver
L19
Phase-A signal
output PG
L20
L21
Phase-B signal
L22
PG
L23 12 V or 5.5 V ±5%,
L24 max. 200 mA
L25 Ground
Complementary
L19
Phase-A signal
L20 output PG
L21
Phase-B signal
L22
PG
L23 12 V or 5.5 V ±5%,
L24
max. 200 mA
L25 Ground
3
57