Tvf Env Tab; Tva Tab - Roland FA-06 Parameter Manual

Parameter
Cutoff V-Curve
Cutoff V-Sens
Resonance V-Sens
TVF Env V-Curve
TVF Env V-Sens
TVF Env T1 V-Sens
TVF Env T4 V-Sens

TVF Env tab

TVF Env Depth
TVF Env Time 1–4
TVF Env Level 0-4

TVA tab

Partial Level
Level V-Curve
Value
FIXED, 1–7
-63–+63
-63–+63
FIXED, 1–7
-63–+63
-63–+63
-63–+63
-63–+63
0–127
0–127
0–127
FIXED, 1–7
Explanation
Selects one of the following seven curves that determine how keyboard playing dynamics
(velocity) influence the cutoff frequency . Set this to
to be affected by the keyboard velocity .
1 2 3
Use this parameter when changing the cutoff frequency to be applied as a result of changes in
playing velocity . If you want strongly played notes to raise the cutoff frequency, set this parameter
to positive (+) value . If you want strongly played notes to lower the cutoff frequency, use negative
(-) value .
This allows keyboard velocity to modify the amount of Resonance . If you want strongly played
notes to have a greater Resonance effect, set this parameter to positive (+) value . If you want
strongly played notes to have less Resonance, use negative (-) value .
Selects one of the following 7 curves that will determine how keyboard playing dynamics will
affect the TVF envelope . Set this to "FIXED"
the keyboard velocity .
1 2 3
Specifies how keyboard playing dynamics will affect the depth of the TVF envelope . Positive (+)
value will cause the TVF envelope to have a greater effect for strongly played notes, and negative
(-) settings will cause the effect to be less .
This allows keyboard dynamics to affect the Time 1 of the TVF envelope . If you want Time 1 to be
speeded up for strongly played notes, set this parameter to a positive (+) value . If you want it to be
slowed down, set this to a negative (-) value .
The parameter to use when you want key release speed to control the Time 4 value of the TVF
envelope . If you want Time 4 to be speeded up for quickly released notes, set this parameter to a
positive (+) value . If you want it to be slowed down, set this to a negative (-) value .
Specifies the depth of the TVF envelope . Higher settings will cause the TVF envelope to produce
greater change . Negative (-) value will invert the shape of the envelope .
Specify the TVF envelope times (Time 1–Time 4) . Higher settings will lengthen the time until the
next cutoff frequency level is reached (For example, Time 2 is the time over which Level 1 will
change to Level 2 .) .
Specify the TVF envelope levels (Level 0–Level 4) . These settings specify how the cutoff frequency
will change at each point, relative to the standard cutoff frequency (the cutoff frequency value
specified in the TVF screen) .
T1 T2 T3
Cuto
Frequency
L0
L1 L2
Note on
T: Time L: Level
Sets the volume of the drum partial . Use this parameter to adjust the volume balance between
drum partials .
MEMO
The volume levels of the Waves from which the drum partial is composed is set with the Wave
Level parameter (p . 62) .
You can select from seven curves that determine how keyboard playing strength will affect the
volume . If you do not want the volume of the drum partial to be affected by the force with which
"FIXED."
you press the key, select
1 2 3
PCM Drum Kit (PCMD)
"FIXED"
if you don't want the Cutoff frequency
4 5 6 7
if you don't want the TVF Envelope to be affected by
4 5 6 7
T4
Time
L3 L4
Note o
4 5 6 7
65