Output/Efx Tab; Eq Tab - Roland FA-06 Parameter Manual

Studio Set
Parameter
V .F .L (Velocity Fade Lower)
V .L (Velocity Range Lower)
V .U (Velocity Range Upper)
V .F .U (Velocity Fade Upper)
Sens (Velocity Sens Offset)

Output/EFX tab

OUT (Output Assign)
Cho (Chorus Send Level)
Rev (Reverb Send Level)

EQ tab

Sw (EQ Switch)
Low Freq (EQ Low Freq)
Low Gain (EQ Low Gain)
Mid Freq (EQ Mid Freq)
Mid Gain (EQ Mid Gain)
Q (EQ Mid Q)
High Freq (EQ High Freq)
High Gain (EQ High Gain)
10
Value
Level
Fade Lower
Range Lower
0–127
1–UPPER
LOWER–127
0–127
-63–+63
MAIN, SUB
0–127
0–127
OFF, ON
16, 20, 25, 31, 40, 50, 63, 80, 100, 125,
160, 200, 250, 315, 400, 500, 630,
800 Hz
-15–+15 dB
16, 20, 25, 31, 40, 50, 63, 80, 100, 125,
160, 200, 250, 315, 400, 500, 630,
800, 1000, 1250, 1600, 2000, 2500,
3150, 4000, 5000, 6300, 8000, 10000,
12500, 16000 Hz
-15–+15 dB
0 .5, 1 .0, 2 .0, 4 .0, 8 .0
630, 800, 1000, 1250, 1600, 2000,
2500, 3150, 4000, 5000, 6300, 8000,
10000, 12500, 16000 Hz
-15–+15 dB
Explanation
Fade Upper
Range Upper
Determines what will happen to the tone's level when the tone is played at a velocity lower than
Velocity Range Lower . If you don't want the tone to sound at all, set this parameter to
SN-A SN-A SN-A
(Ac . Piano) (Organ) (Other)
ü –
Specifies the lowest velocity at which the part will sound .
Specifies the highest velocity at which the part will sound .
Determines what will happen to the tone's level when the tone is played at a velocity greater than
Velocity Range Upper . If you don't want the tone to sound at all, set this parameter to
SN-A SN-A SN-A
(Ac . Piano) (Organ) (Other)
–
ü
Adjusts the velocity sensitivity . The higher the value, the greater the sensitivity .
SN-A SN-A SN-A
(Ac . Piano) (Organ) (Other)
–
ü
Specifies the output destination for each part .
MAIN: Output to the MAIN OUTPUT jacks .
SUB: Output to the SUB OUTPUT jack .
Adjusts the amount of chorus for each part .
If you don't want to add the chorus effect, set it to 0 .
Adjusts the amount of reverb for each part .
If you don't want to add the reverb effect, set it to 0 .
EQ for each part on/off setting
Frequency of the low range .
Gain of the low frequency range .
Frequency of the middle range .
Gain of the middle frequency range .
Width of the middle frequency range .
Set a higher value for Q to narrow the range to be affected .
Frequency of the high range .
Gain of the high frequency range .
Velocity
SN-S SN-D
ü ü ü
SN-S SN-D
ü ü ü
SN-S SN-D
–
ü ü
"0."
PCMS PCMD
ü ü
"0."
PCMS PCMD
ü ü
PCMS PCMD
ü ü