Amp Tab; Lfo Tab - Roland FA-06 Parameter Manual

Parameter

Amp tab

[4]
*1: Shown only if you press the (Pro Edit) button to enter pro edit mode .
AMP Level (Level)
AMP Level V-Sens (Velo Sens)
AMP Pan (Pan)
AMP Level Keyfollow *1
AMP Env Attack (A)
AMP Env Decay (D)
AMP Env Sustain (S)
AMP Env Release (R)

LFO tab

LFO Shape (Shape)
LFO Rate (Rate)
LFO Tempo Sync Sw
(Tempo Sync Switch)
LFO Tempo Sync Note (Rate)
LFO Fade Time (Fade Time)
LFO Key Trigger (Key Trigger)
LFO Pitch Depth (Pitch Depth)
LFO FILTER Depth (Filter Depth)
LFO AMP Depth (Amp Depth)
LFO Pan Depth (Pan Depth)
Value
0–127
-63–+63
L64–63R
-100, -90, -80, -70, -60, -50, -40, -30,
-20, -10, 0, +10, +20, +30, +40, +50,
+60, +70, +80, +90, +100
0–127
0–127
0–127
0–127
Selects the LFO waveform .
TRI
SIN
SAW
SQR
S&H
RND
0–127
OFF, ON
16, 12, 8, 4, 2, 1, 3/4, 2/3, 1/2, 3/8, 1/3,
1/4, 3/16, 1/6, 1/8, 3/32, 1/12, 1/16,
1/24, 1/32
0–127
OFF, ON
-63–+63
-63–+63
-63–+63
-63–+63
Explanation
Partial volume .
Here's how you can make the volume vary according to the strength with which you play the
keyboard .
Here's how to change the stereo position of the partial .
Specify this if you want to vary the volume according to the position of the key that you play .
With the C4 key (middle C) as the base volume,
play above C4; "-" values will make the volume decrease . Higher values will produce greater
change .
Specifies the attack time of the
amp envelope .
This specifies the time from the
moment you press the key until
the maximum volume is reached .
Specifies the decay time of the
amp envelope .
This specifies the time from when
the maximum volume is reached,
until it decays to the sustain level .
Specifies the sustain level of the
amp envelope .
This specifies the volume level
that will be maintained from
when the attack and decay times
have elapsed until you release
the key .
Specifies the release time of the
amp envelope .
This specifies the time from
when you release the key until
the volume reaches its minimum
value .
Triangle wave
Sine wave
Sawtooth wave
Square wave
Sample and Hold (The LFO value will change once each cycle .)
Random wave
Specifies the LFO rate when Modulation LFO Tempo Sync Switch is OFF .
If this is ON, the LFO rate can be specified as a note value relative to the tempo .
Specifies the LFO rate when Modulation LFO Tempo Sync Switch is ON .
This specifies the time from when the partial sounds until the LFO reaches its maximum amplitude .
Fade Time
If this is on, the LFO cycle will be restarted when you press a key .
This allows the LFO to modulate the pitch, producing a vibrato effect .
This allows the LFO to modulate the FILTER CUTOFF (cutoff frequency), producing a wah effect .
This allows the LFO to modulate the AMP LEVEL (volume), producing a tremolo effect .
This allows the LFO to make the PAN (stereo position) vary (Auto Panning) .
SuperNATURAL Synth Tone (SN-S)
"+"
values will make the volume increase as you
Key-off
Cutoff
frequency
Key-on
Time
35