D-Beam Tab - Roland FA-06 Parameter Manual

Parameter

D-Beam tab

D-Beam Assign Source (System)
D-Beam Switch
Solo Synth (System)
* The various Solo Synth (System) parameters are system parameters .
Level
Chorus Send Level
Reverb Send Level
Range
Osc 1 Waveform
Osc 1 Pulse Width
Osc 1 Coarse Tune
Osc 1 Fine Tune
Osc 2 Waveform
Osc 2 Pulse Width
Osc 2 Coarse Tune
Osc 2 Fine Tune
Osc 2 Level
Osc Sync Switch
Filter Type
Cutoff
Resonance
LFO Rate
LFO Osc 1 Pitch Depth
LFO Osc 2 Pitch Depth
LFO Osc 1 Pulse Width Depth
LFO Osc 2 Pulse Width Depth
Assignable
D-Beam Assign
Value
SYSTEM, STUDIO
Specify the functions that are controlled by the D-BEAM controller .
OFF
SOLO SYNTH
EXPRESSION
ASSIGNABLE
0–127
0–127
0–127
2–8OCT
SAW, SQR
0–127
-48–+48
-50–+50
(same as Osc 1)
0–127
OFF, ON
Specifies the type of filter .
OFF
LPF (Low Pass Filter)
BPF (Band Pass Filter)
HPF (High Pass Filter)
PKG (Peaking Filter)
0–127
0–127
0–127
-63–+63
-63–+63
-63–+63
-63–+63
Specifies the function that is assigned to the D-Beam Switch
MEMO
You can use the SOUND MODIFY knobs to control the
control the same parameters .
OFF
CC01–31, 32 (OFF), 33–95
BEND DOWN
BEND UP
AFTERTOUCH
Explanation
Specifies whether the functions controlled by the D-BEAM controller will be determined by the
system settings (SYSTEM) or by the studio set settings (STUDIO) .
* D-Beam Assign Source (System) is a system parameter .
* "SYSTEM,"
If you choose the settings of the studio set parameters D-Beam Switch and
Assignable are ignored .
No function is assigned .
The D-BEAM controller operates as a monophonic synthesizer .
The D-BEAM controller controls the volume .
The D-BEAM controller controls the function that you assign .
Adjusts the volume of the solo synth .
Adjusts the chorus send level .
Adjusts the reverb send level .
Adjusts the range in which the pitch of the solo synth will vary .
Selects the waveform .
SAW (sawtooth wave), SQR (square wave)
Specifies the pulse width of the waveform .
By cyclically modifying the pulse width you can create subtle changes in the tone .
Adjusts the pitch of the tone's sound (in semitones, +/-4 octaves) .
Adjusts the pitch of the tone's sound (in 1-cent steps) .
Adjusts the level of the Osc 2 .
Turning this switch on produces a complex sound with many harmonics . This is effective when the
Osc 1 pitch is higher than the Osc 2 pitch .
No filter is used .
This reduces the volume of all frequencies above the cutoff frequency (Cutoff ) .
This leaves only the frequencies in the region of the cutoff frequency, and cuts the rest .
This cuts the frequencies in the region below the cutoff frequency .
This emphasizes the frequencies in the region of the cutoff frequency .
Frequency at which the filter begins to have an effect on the waveform's frequency components .
Emphasizes the portion of the sound in the region of the cutoff frequency, adding character to the
sound .
Adjusts the modulation speed of the LFO .
Specifies the depth to which the LFO will modulate the Osc 1 pitch .
Specifies the depth to which the LFO will modulate the Osc 2 pitch .
Specifies the depth to which the LFO will modulate the pulse width of the Osc 1 waveform .
*
The Pulse Width is activated when
Specifies the depth to which the LFO will modulate the pulse width of the Osc 2 waveform .
* The Pulse Width is activated when
"ASSIGNABLE"
"CUTOFF"–"TFX CTRL"
No function is assigned .
Controller number 1–31, 32, 33–95
CC16 (General-1)–CC19 (General-4) and CC80 (General-5)–CC83 (General-8) apply specific effects if
a SuperNATURAL acoustic tone is selected (p . 118) .
The same effect as moving the pitch bend lever to the left .
The same effect as moving the pitch bend lever to the right .
Aftertouch
"SQR"
is selected with Osc 1 waveform .
"SQR" is selected with Osc 2 waveform .
setting .
parameters . You can also use the D-BEAM controller to
Studio Set
7