Menu Operations; Recalling, Editing, And Saving A Scene - Roland Serato Owner's Manual

Menu Operations

Recalling, Editing, and Saving a Scene

A "scene" contains settings for mixer, mic, and output. You can save ten
scenes in the DJ-707M unit.
Scene
5 Mixer settings
5 Mic 1–3 settings
5 MASTER OUT settings
5 BOOTH OUT settings
5 ZONE OUT settings
Mic section
Turn each
button on/off
When the unit is shipped from the factory, several scenes are already saved.
You can edit and overwrite these scenes.
Scene Explanation
The same audio as MASTER OUT is output from ZONE OUT.
1: Standard
This allows the same use as a standard DJ controller.
Mic audio is not output from ZONE OUT.
2: Two-Room
This is useful when you want to output only the song audio to a
different venue than the main venue.
The deck 4 audio is output only from ZONE OUT, without being mixed
into MASTER OUT or BOOTH OUT.
3: DECK4-ZONE
This is useful when you want to output different music to the main
venue and to another venue.
The mic audio is output only from ZONE OUT.
4: MICs-ZONE
This is useful when you want the mic audio to be output from different
speakers.
A multi-band compressor is applied to each output.
5: SoundBoost
This makes mixing easier when using TR, etc.
Recalling a Scene (Scene Load)
1.
Press the [MENU] button.
2.
Turn the [SELECT (ENTER)] knob to select "Scene Load," and
press the knob.
Scene Load
1:Standard
3.
Turn the [SELECT (ENTER)] knob to select the scene that you
want to recall, and press the knob.
A confirmation message appears.
Load Scene?
CANCEL[OK]
If you decide to cancel, use the [SELECT (ENTER)] knob to make "CANCEL"
blink, and press the knob.
4.
Press the [SELECT (ENTER)] knob.
The selected scene is loaded.
18
Scene 10
Save Scene 1
Scene 1
Scene 1
Scene 1
Load
<
Editing a Scene (Scene Edit)
1.
Press the [MENU] button.
2.
Turn the [SELECT (ENTER)] knob to select "Scene Edit," and
press the knob.
MENU>SCENE EDIT
Mixer Setting
3.
Turn the [SELECT (ENTER)] knob to select the setting that you
want to edit, and press the knob.
Mixer: FX(All)<
FILTER
4.
Turn the [SELECT (ENTER)] knob to select the parameter that
you want to edit, and press the knob.
The parameter value blinks.
5.
Turn the [SELECT (ENTER)] knob to change the value, and press
the knob.
The value is confirmed.
Parameter Value (Bold: default) / Explanation
Mixer Setting
FX (ALL) specifies the same effect for the entire channel mixer.
FX (Ch1–4) individually specify an effect for each channel.
FILTER
DUB ECHO
JET
NOISE
FX (ALL)
FX (Ch1–4)
REVERB
DELAY
BIT CRUSH
PHASER
NOISE2
SIDE CHAIN
SLICER
ROLL
ROLL FILTER
LOOP PITCH
LOOP FILTER
VINYL SIM
Selects the output that uses anti-feedback for the mic input.
OFF
Anti.FB
MASTER
BOOTH
ZONE
Mode SERATO, INTERNAL
Specifies the controller when using DVS.
DVS Deck TURNTABLE
CDJ
Applies a filter.
If you turn the [FILTER/FX] knob toward the right, only
the high-frequency range is heard. If you turn the
knob toward the left, only the low-frequency range
is heard.
Adds a delayed sound several times while attenuating
it.
If you turn the [FILTER/FX] knob toward the right,
the echo effect is added only to the high-frequency
range.
If you turn the knob toward the left, the echo effect is
added only to the mid-frequency range.
The farther you turn the knob, the longer the interval
between echoes.
Applies a flanger effect.
If you turn the [FILTER/FX] knob toward the right, the
peak varies cyclically.
If you turn the knob toward the left, the peak lowers
according to the knob's position.
Adds noise.
If you turn the [FILTER/FX] knob toward the right, the
pitch of the noise rises.
If you turn the knob toward the left, the pitch falls.
Applies a reverb.
Applies a delay.
Creates a lo-fi sound.
If you turn the [FILTER/FX] knob toward the right, only
the high-frequency range is heard. If you turn the
knob toward the left, only the low-frequency range
is heard.
Applies a phaser effect.
If you turn the [FILTER/FX] knob toward the right, the
peak varies cyclically. If you turn the knob toward the
left, the peak lowers according to the knob's position.
Adds peaky noise.
If you turn the [FX] knob toward the right, the pitch
of the noise rises. If you turn the knob toward the left,
the pitch falls.
Lowers the level in synchronization with the tempo.
Slices the sound in synchronization with the tempo.
Plays the sound repeatedly.
Plays the sound repeatedly and applies a filter.
Plays the sound repeatedly and modifies the pitch.
Plays the sound repeatedly and modifies the pitch
and filter.
Simulates sound heard from an analog record.
Anti-feedback is not used.
Anti-feedback is applied only to the output sound
from the selected jacks.
Selects whether mixing is done in Serato DJ Pro or in
the DJ-707M.
Turntable (analog)
DJ player