System Settings; Dj-707M Version Indication (Version); Returning To The Factory Settings (Factory Reset) - Roland Serato Owner's Manual

Menu Operations

System Settings

1.
Press the [MENU] button.
2.
Turn the [SELECT (ENTER)] knob to select "System Setting," and
press the knob.
Sys: PC-B USB<
VENDOR
3.
Turn the [SELECT (ENTER)] knob to select the parameter that
you want to edit, and press the knob.
The parameter value blinks.
4.
Turn the [SELECT (ENTER)] knob to change the value, and press
the knob.
The value is confirmed.
Parameter Value (Bold: default) / Explanation
Specifies the USB driver when using the PC-B port.
Choose this if you want to use a USB driver downloaded from
VENDOR
the Roland website.
Choose this if you want to use the generic USB driver
PC-B USB
provided by your computer's operating system.
* If this is set to GENERIC, you can't use the unit with
GENERIC
Serato DJ Pro.
* If you are using this with an iOS device, choose GENERIC.
For details, refer to "Using an iOS Device" (p. 22).
Specifies the margin at both ends of the cross fader. Higher
X-Fader Mgn
0–10 values increase the margin, providing more play at each end
of the cross fader.
Specifies the velocity curve of the performance pads (the
Low, Mid,
way in which the level changes in response to the strength of
High
your strike on the pad).
Low
high
Pad Curve
Level
low
weak
Strength of pad strike
Adjusts the sensitivity of the performance pads.
Pad Sens
1–10
Higher values improve the sensitivity.
Adjusts the sensitivity for when you take your hand off of
JogDialSens
1–8–10 the jog dial.
Higher values improve the response.
When applying backspin to the jog dial, this setting lets you make backspin
continue longer than the distance that the jog dial actually rotated.
Backspin operation occurs according to the actual distance
OFF
of rotation.
Bkspin Len
DEPTH1
Backspin operation occurs longer than the actual distance
DEPTH2 of rotation.
The higher the value, the longer backspin is applied.
DEPTH3
* When a computer is connected, this setting is ignored.
OFF, Specifies the time (minutes) from when the DJ-707M was last
Demo Mode
3–5–20 min. operated until it enters demo mode.
If this is "OFF, " demo mode will not operate.
Adjusts the brightness when a button, pad, or indicator is lit.
LED Bright
1–5
Higher values increase the brightness.
LCD Ctrst
1–5–10 Adjusts the display contrast.
When no operation has been performed for a certain length
DISABLE, of time (240 min.), the power turns off automatically.
Auto Off
240 min. If you don't want the power to turn off automatically, set
this "OFF. "
If this is "ON, " the input signals to INPUT CH 1–4 are output
Input Mix
OFF, ON without change to MASTER OUT when the input select switch
is set to "PC. "
Specifies whether the INPUT CH 1 and CH 3 signals are exchanged with the
CH 2 and CH 4 signals when sent to the computer.
InputChSwap
NORMAL Don't swap. The outputs are as printed on the panel.
SWAP Swap the outputs of CH 1 and 3 and CH 2 and 4.
If this is "ON, " the unit operates as a general-purpose MIDI
Ctrl surface
OFF, ON
controller.
20
Mid Hi
strong

DJ-707M Version Indication (Version)

1.
Press the [MENU] button.
2.
Turn the [SELECT (ENTER)] knob to select "Version," and press
the knob.
Version:
*.**

Returning to the Factory Settings (Factory Reset)

Here's how the settings stored in the unit can be reset to their factory-set
values.
1.
Press the [MENU] button.
2.
Turn the [SELECT (ENTER)] knob to select "Factory Reset," and
press the knob.
FACTORY RESET:
Target
3.
Turn the [SELECT (ENTER)] knob to select the settings that you
want to reset.
Value Explanation
ALL
All settings stored in the unit
SCENE
Scene settings
SYSTEM
System settings
4.
Press the [SELECT (ENTER)] knob.
A confirmation message appears.
Factory Reset?
[Cancel]OK
If you decide to cancel, use the [SELECT (ENTER)] knob to make "CANCEL"
blink, and press the knob.
5.
Use the [SELECT (ENTER)] knob to make "OK" blink, and press
the knob.
Factory reset begins.
When the display indicates "Completed. turn off power., " factory reset is
complete.
NOTE
Never turn off the power until the display indicates "Executing... "
6.
Turn the DJ-707M's power off and then on again.
All