Table of Contents
Advertisement
Item number Display indication
013
PB/EE SELECT P1
014
PB/EE SELECT P2
015
PB/EE SELECT P3
BI
016
CHARACTER POSITION V
BI
SHIFT
019
SYSTEM OPERATE
CONFIGURATION
022
ERROR INFORMATION
BI
SELECT
SUB MENU
ERROR/WARNING
NOT ENOUGH SPACE
027
– FAST REBOOT
I SUB MENU
EXECUTE
028
AUDIO BIT LENGTH
030
GOOD SHOT PARAMETER
B
SUB MENU
SAVE DUR. (1 ..
TRIM SIZE (0 ..
AUTO SAVE
CUEUP SELECT
3-20 (E)
3-4 Setup
Basic menu items (Continued)
Settings
For the PANEL, DTR+PANEL, DTR+DTR and BVE modes, specifies when the PB port
enters the state indicated by SETUP MENU 108 AUTO EE SELECT, and whether it
should automatically correspond to the REC port.
PB
: Always output at the PB side.
PB/EE
: Switch to the REC side according to the SETUP MENU 108 status.
Note:
In the BVE mode, "PB/EE SELECT P2" item (menu 014) is disabled.
The vertical position of text display of time codes output from the MONITOR OUT
terminal, SDI (SUPER) and ANALOG COMPOSITE (SUPER) terminals, can be more
minutely adjusted than is possible with SETUP MENU 003.
0
.. 20
Select the application mode for this unit.
PANEL
DTR + PANEL : Controls R1 and P1 with the DTR-3000, controls R2 and P2 (or P2 and
DTR + DTR
BVE
Activate or deactivate various status information display output from the MONITOR
OUT connectors of the SDI (SUPER) or ANALOG COMPOSITE (SUPER) connectors.
Note:
This setting item takes priority over the system setup panel CHARACTER
switch setting.
Specifies whether the ERROR/WARNING display is on or off.
on
off
Note:
Even if this is set to "on", the warning message "Ref. Missing" is not
displayed.
Specifies whether a warning message is displayed when there remains approximately
five minutes of recording time on the HDD.
on
off
Carry out a fast reboot of the system. This is faster than switching the system off and on
again, because the HDD power supply is not turned off.
Start
: Start reboot.
Select the word length for audio sampling.
16 bits
20 bits
Notes:
• Bit length cannot be set for individual lots of material.
• After changing the settings for this item, all material must be erased using
Specifies the partial save method to use for Replay scenes with the DTR-3000, for
highlight editing with DTR+Panel and DTR+DTR modes.
5
.. 255)
Specifies the partial save duration, in seconds.
5
.. 15)
Specifies the trim length to be added before and after the partial save period.
Specifies the trigger command to start partial saving.
off
cue up with data : Start partial save after cue up.
Specifies the time data at which to perform cue up in DTR+PANEL or DTR+DTR
mode.
FTC
: Regardless of the timer mode, cue up is performed with TM2 (FTC).
timer mode : Cue up is performed according to the timer mode.
Notes:
• When using the DISK INDIVIDUAL MODE of the DTR-3000, select
• When using a controller other than the DTR-3000, select "timer mode". In
: All ports are controlled only from the optional BKMA-505
P3) from the BKMA-505.
: The R1/P1 and R2/P2 pairs are controlled by two DTR-3000 units.
: R1 and P1 are controlled as an RP port by the editor.
-ALL ERASE (menu 099).
: Partial save disabled
"FTC". However, select "timer mode" in the following cases:
- When performing direct cue up in 205 point mode from the keypad.
- When performing cue up in 10 point mode with SERACH + CUEn.
this situation it is not possible to use the GOOD SHOT function, so set the
AUTO SAVE item (menu 030) to "off".
Advertisement
Table of Contents
