Emergency Icon - Interlogix Simon XTi-5 Version 2 User Manual

To set the time:
1. From the Status & Settings screen, select Set
Date/Time.
2. Enter access code.
3. From the Set Date/Time screen press the first box to set
hour and press the SAVE icon.
4. Press the second box to set minutes and press the
SAVE icon.
5. Press a.m / p.m. box to toggle a.m / p.m. setting.
To set the date:
1. From the Set Date/Time screen press the first box in the
second row to set the month and press the SAVE icon.
2. Press the second box to set the day and press the
SAVE icon.
3. Press the third box and enter the year and press the
SAVE icon.
4. Press the CLOSE icon repeatedly to exit.

Emergency Icon

In an emergency, touch the Emergency icon. An Emergency
screen appears (see Emergency icon in Table 1 on page 1).
You will see three icons (Panic, Police, or Fire). Select the
appropriate icon.
Note: If your system is connected to a security monitoring service,
the authorities will be notified. This option may not be
enabled. Contact your dealer for details.
If you initiate an emergency alarm by mistake, you can
cancel the alarm by touching the red Alarm icon and entering
your code within 30 seconds (typical time limit, contact your
dealer for more information on your system configuration).
Fire Alarm Verification
If this option is off, the panel immediately reports to the
central station when a smoke detector goes into alarm.
With this option on, if a single smoke detector goes into
alarm, the panel will not report for 60 seconds unless
another smoke detector goes into alarm. If the first smoke
detector is cleared of an alarm within the first 60 seconds, no
report will be sent to the central station unless it or a second
smoke detector goes into alarm within the panel siren
timeout period (5 minutes).
4 / 10
Ask your security provider how this option is programmed.
Arming and Disarming
Use the steps below to arm and disarm your system:
To disarm:
Press "PRESS TO DISARM".
1.
2. Enter your code when the keypad screen appears. If
you enter an incorrect code, press the Clear icon and
enter the correct code.
Note: You have four seconds between number presses to enter
the code or you will be returned to the Main screen.
To arm STAY or AWAY (if two buttons are shown) or
STAY, AWAY, Motions Sensors Only (if three buttons
are shown):
Press "PRESS TO ARM" icon.
1.
Press "STAY or AWAY, MOTION SENSORS ONLY, or
2.
ARM ALL".
3. If a code is required, enter your code when the keypad
screen appears.
The panel starts an exit delay and sounds exit beeps until
the exit delay expires (see Table 4 on page 5).
Unvacated Premises
Unvacated Premises is a feature that determines whether
the system automatically arms down to level 2 (STAY -
doors and windows) if arming the system to level 4 (AWAY -
doors, windows, and motion sensors) without opening or
closing a perimeter door (on), or remains at the armed level
chosen (off). This feature does not work from a key fob. Auto
bypass must be on for this feature to work. Check with your
security provider to see how these options are programmed
for your system.
Swinger Shutdown
This setting determines if a sensor or zone will go into alarm
only once during an arming period (an active arming level)
and will not be active again until the alarm is canceled
(Swinger Shutdown is enabled) or the sensor or zone will
always be active and will go into alarm multiple times during
an arming period (an active arming level) without canceling
the alarm (Swinger Shutdown is disabled).
Note: Swinger Shutdown does not affect Smoke, Fire, Carbon
Monoxide and Environmental sensors.
Ask your security provider how this option is programmed
and have them explain how it will affect your system
operation.
P/N 466-5437 • REV A • 16OCT18