Regency Ultimate U39E Series Owners & Installation Manual page 24

installation
e) Cut the 2 ft. or 4 ft. section of rigid pipe to
length. Ensure that the pipe length when
cut will seat onto both the starter collar and
elbow. Crimped section of rigid
the 90
o
pipe seats into the 90
the uncrimped side of pipe.
Dismantle all pipe sections including vent
terminal.
3. Attach the 4" dia. flex liner to the vent terminal
ensuring that the flex overlaps the collar of the
vent terminal by a minimum of 1-3/8"(35mm).
Use Mill-Pac to seal and secure with 3 of the
#8 x 1/2" screws (stainless steel).
4. Attach the adjustable pipe section to the vent
terminal using Mill-Pac and attach with 3 of
the #8 x 1/2" screws (stainless steel).
Note: The pipe seam should be facing
down.
Note: To make the installation more
a e s t h e t i c a l l y
recommend framing out a square
that the cap can be mounted on.
Note: If installing termination on a
siding covered wall, a vinyl siding
standoff or furring strips must be
used to ensure that the termination
is not recessed into the
siding. For vinyl
siding standoff
installation refer
to the Dura-Vent
T e r m i n a t i o n
instructions.
5. Slide the partially connected pipe and vent
terminal assembly through the wall thimbles
(from the exterior into the interior) and secure
the cap to the exterior wall with 4 of the supplied
screws (#8 x 1-1/2" drill point, stainless steel).
Note: pilot holes will need to be drilled through
the wall thimble on all 4 corners.
Note: The four screws provided for the
vent cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
6. A bead of non-hardening mastic should be run
around both the termination and vinyl siding
standoff to prevent water from entering and
to make a tight seal between the cap and the
standoff.
|
24
Regency U39E-11 ULTIMATE™ Freestanding Gas Stove
®
o elbow. Only cut
p l e a s i n g , w e
7. Stretch the 4" dia. flex liner out fully and get a
trial fit of the liner onto the 4" dia. starter collar.
8. Cut the 4" dia. flex liner to the desired size.
Hint: leave an extra 12" to 16" of length, this will
make the final assembly easier to work with.
9. Secure the 4" dia. flex liner to the 4" adapter with
Mill-Pac and 3 of the #8 x 1/2" screws (stainless
steel).
10. Slide the decorative Thimble Cover over the
a l l
i d e W
Furstrp.eps
O u t s pipe sections and secure with 4 screws (#8 x
1-1/2" drill point, black) to the wall.
see also c34020a.eps
11. Slide the 90
Furring
Strips
ft. or 4 ft. pipe section (crimp end up) over the
4" dia. flex liner.
12. Slide the trim collar over the adjustable pipe
sections to cover the joint of the telescopic
section.
13. Install the spring spacers onto the pipe sections.
r i e u r
e x t é
M u r
furstrpf.eps
14. Secure the 4" dia. flex liner with adapter onto
french
the stove collar. Put a bead of Mill-Pac around
the appliance adapter and secure with 3 screws
(#8 x 1/2, stainless steel).
Fourrures en bois
15. Attach the pipe section onto the starter collar
by sealing with Mill-Pac and securing with 3 of
the #8 x 1/2" (black) screws. Pipe seams should
be facing the wall.
16. Attach the 90
sealing with Mill-Pac and securing with 3 of the
#8 x 1/2" screws (black).
elbow (crimp end up) and the 2
o
o elbow onto the pipe section by
17. Slide the adjustable pipe section onto the 90
elbow. The flex may have to be compressed
back in order for the adjustable pipe to
properly mate to the elbow. Seal with Mill-Pac
and secure with 3 of the #8 x 1/2" screws
(black). Pipe seams facing down.
18. Install the trim collar over the starter collar
and secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
NOTE: For best results and optimum
performance with each approved venting
system, it is highly recommended to apply
"Mill-Pac" sealant (supplied) to every inner
pipe connection. Failure to do so may result
in drafting or performance issues not covered
under warranty.
o