Parameter List - Omron 3G3RX2 Series Quick Start Manual

7. Parameter List

Parameter List Parameter List Parameter List
Code
AA101 Main speed input source selection, 1st-motor
AA102 Sub frequency input source selection, 1st-motor
AA104 Sub speed setting, 1st-motor
Calculation symbol selection for Speed
AA105
motor
AA106 Add frequency setting, 1st-motor
AA111 Run-command input source selection, 1st-motor
AA114 RUN-direction restriction, 1st-motor
AA115 STOP mode selection, 1st-motor
AA-12 RUN-key of keypad Rotation Direction, 1st-motor
AA121 Control mode selection, 1st-motor
AA123 Vector control mode selection, 1st-motor
AA-13 STOP-key enable at RUN-command from
AA201 Main speed input source selection, 2nd-motor
AA202 Sub speed input source selection, 2nd-motor
AA204 Sub speed setting, 2nd-motor
AA205 Calculation symbol selection for Speed reference, 2nd-motor
AA206 Add frequency setting, 2nd-motor
AA211 Run-command input source selection,
AA214 RUN-direction restriction, 1st-motor
AA215 STOP mode selection, 1st-motor
AA221 Control mode selection, 2nd-motor
AA223 Vector control mode selection, 2nd-motor
Ab-01 Frequency conversion gain
Ab-03 Multispeed operation selection
Ab-11 Multispeed-1 setting
Ab110 Multispeed-0 setting, 1st-motor
Ab-12 Multispeed-2 setting
Ab-13 Multispeed-3 setting
Ab-14 Multispeed-4 setting
Ab-15 Multispeed-5 setting
Ab-16 Multispeed-6 setting
Ab-17 Multispeed-7 setting
Ab-18 Multispeed-8 setting
Ab-19 Multispeed-9 setting
Ab-20 Multispeed-10 setting
Ab-21 Multispeed-11 setting
Ab210 Multispeed-0 setting, 2nd-motor
Ab-22 Multispeed-12 setting
Ab-23 Multispeed-13 setting
Ab-24 Multispeed-14 setting
Ab-25 Multispeed-15 setting
AC-01 Acceleration/ Deceleration time input selection
AC-02 Acceleration/ Deceleration selection
AC-03 Acceleration curve selection
AC-04 Deceleration curve selection
AC-05 Acceleration curve constant setting
AC-06 Deceleration curve constant setting
AC-08 EL-S-curve ratio @start of acceleration
AC-09 EL-S-curve ratio @end of acceleration
AC-10 EL-S-curve ratio @start of deceleration
AC-11 EL-S-curve ratio @start of deceleration
AC115 Select method to switch to Accel2/Decel2 Profile, 1st-motor
AC116 Accel1 to Accel2 Frequency transition point, 1st-motor
AC117 Decel1 to Decel2 Frequency transition point, 1st-motor
AC120 Acceleration time setting 1, 1st-motor
AC122 Deceleration time setting 1, 1st-motor
AC124 Acceleration time setting 1, 1st-motor
AC126 Deceleration time setting 1, 1st-motor
AC215 Select method to switch to Accel2/Decel2 Profile, 2nd-motor
3G3RX2 Series High-function General-purpose Inverter User's Manual (I620)
Function name
reference, 1st-
terminal, 1st-motor
2nd-motor
Monitoring and setting items
01 (Setting by Terminal [Ai1]) /02 (Setting by Terminal [Ai2]) /03 (Setting by Terminal [Ai3]) /04
(Setting by Terminal [Ai4]) /05 (Setting by Terminal [Ai5]) /06 (Setting by Terminal [Ai6]) /07 (Setting
by parameter) /08 (Setting by RS485) /09 (Option-1) /10 (Option-2) /11 (Option-3) /12 (Pulse train
input(internal)) /13 (Pulse train input(Option)) /14 (Setting by EzSQ) /15 (PID function) /16 (Volume on
keypad)
00 (Disable) /01 (Setting by Terminal [Ai1]) /02 (Setting by Terminal [Ai2]) /03 (Setting by Terminal
[Ai3]) /04 (Setting by Terminal [Ai4]) /05 (Setting by Terminal [Ai5]) /06 (Setting by Terminal [Ai6])
/07 (Setting by parameter) /08 (Setting by RS485) 09 (Option-1) /10 (Option-2) /11 (Option-3) /12 (Pulse
train input(internal)) /13 (Pulse train input(Option)) /14 (Setting by EzSQ) /15 (PID function) /16
(Volume on keypad)"
0.00～590.00
00 (Disable) /01 (Addition(ADD)) /02 (Subtraction(SUB)) /03 (Multiplication(MUL))
−590.00～＋590.00（Hz）
00 (Terminal [FW]/[RV]) /01 (3-wire) /02 (RUN key on keypad) /03 (Setting by RS485) /04 (Option-1) /05
(Option-2) /06 (Option-3)
00 (Disable) /01 (Enable only Forward rotation) /02 (Enable only Reverse rotation)
00 (Deceleration until stop) /01 (Free-run stop)
00 (Forward) /01 (Reverse)
IM control: 00 (VF control (Constant torque)) /01 (VF control (Reduced torque)) /02 (VF control (Free-
V/f)) /03 (Constant torque with Automatic- trq boost)) /04 (VF control with encoder (Constant torque))
/05 (VF control with encoder (Reduced torque)) /06 (VF control with encoder (Free-V/f)) /07 (VF control
with PG (Constant torque with Automatc-trq boost)) /08 (Sensorless vector control) /09（0Hz Sensorless
vector control）/10（Vector control with encoder）
SM/PMM control: 11 (Synchronous start up for smart sensorless vector control）/12（IVMS start up for
smart sensorless vector control）
00 (Speed/Torque control mode) /01 (Pulse train position control) /02 (Position control) /03 (High-
resolution position control)
00 (Disable) /01 (Enable) /02 (Enable at only trip reset)
same to AA101
same to AA102
same to AA104
same to AA105
same to AA106
same to AA111
same to AA114
same to AA115
Same as AA121, except 12
same to AA123
0.01～100.00
00 (Binary (16-speeds)) /01 (Bit (8-speeds))
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
Same as Ab110
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～590.00（Hz）
00 (Setting by parameter) /01 (Setting from Option-1) /02 (Setting from Option-2) /02 (Setting from
Option-3) /04 (Setting by programing function)
00 (Common setting) /01 (Multi stage Acceleration/ Deceleration)
00 (Liner Acceleration) /01 (S-curve Acceleration) /02 (U-curve Acceleration) /03 (Reverse U-curve
Acceleration) /04 (Eleveter S-curve Acceleration)
00 (Liner Acceleration) /01 (S-curve Acceleration) /02 (U-curve Acceleration) /03 (Reverse U-curve
Acceleration) /04 (Eleveter S-curve Acceleration)
1～10
1～10
0～100
0～100
0～100
0～100
00 (Switching by [2CH] terminal) /01 (Switching by setting) /02 (Switching only when rotation is
reversed)
0.00～590.00（Hz）
0.00～590.00（Hz）
0.00～3600.00（s）
0.00～3600.00（s）
0.00～3600.00（s）
0.00～3600.00（s）
00 (Switching by [2CH] terminal) /01 (Switching by setting) /02 (Switching only when rotation is
reversed)
Units
―
―
Hz
―
0.01Hz
―
―
―
―
0
―
―
―
―
―
―
―
―
―
―
0
―
0.01
―
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
―
―
―
―
―
―
1%
1%
1%
1%
―
0.01Hz
0.01Hz
0.01s
0.01s
0.01s
0.01s
―
1
2