General Specifications; Common Specifications - Mitsubishi FR-S520-*K Series Manual

Hide thumbs

Table Of Contents

Table of Contents

General Specifications

Specifications

Type

Applicable motor capacity (kW) (Note 1)

Rated capacity (kVA)(Note 2)

Rated current (A)

Output

Overload current rating (Note 3)

Voltage (Note 4)(Note 6)

Rated input AC voltage/frequency

Tolerable AC voltage fluctuation

Power supply

Tolerable frequency fluctuation

Power facility capacity (kVA)(Note 5)

Protective structure (JEM 1030)

Cooling method

Approximately weight (kg)

1. The applicable motor indicates the maximum applicable capacity when using a Mitsubishi standard 4-pole motor.

(Notes)

2. The rated output capacity is 230V for the 3-phase 200V output voltage, and 440V for the 3-phase 400V output voltage.

3. The overload current rating percentage indicates the percentage in respect to the inverter's rated output current. When used repeatedly, it is necessary to wait for the inverter motor to return to a temperature

less than the temperature for the 100% load.

4. The maximum output voltage will not exceed the power supply voltage for the 3-phase 200V/400V power input specification product and the single-phase 200V power input specification product. The

single-phase 100V power input specification product cannot output more than twice the power voltage.

5. The power capacity will change according to the power side impedance (including the input reactor or wire) values.

6. For the single-phase 100V power input specification product, when a load is applied on the motor, the output voltage will drop by approx. 10 to 15%. However, when using a general-purpose motor, the

load must be reduced before use.

Common Specifications

Control method

Output frequency range

Frequency setting resolution

Frequency precision

Starting torque

Acceleration/deceleration time setting

Regenerative (Note 1)

Braking torque

DC braking

Input signals

Operation functions

For meter

Protection and warning functions

Ambient temperature and humidity

Storage temperature (Note 3)

Atmosphere

Altitude and vibration

(Notes)

1. The indicated braking toque is the short-term average torque (which changes with motor loss) when the motor alone is decelerated from 60Hz. It is not the continuous regenerative torque. Deceleration

from frequencies exceeding the base frequency will have a lower average deceleration torque value.

2. If an undervotlage occurs, an error will not be output, but the output will be cutoff. Operation can be resumed after restoring the power, but depending on the operation state (size of load, etc.), the overcur-

rent protection or regenerative overvoltage protection may function when the power is restored.

3. This is the temperature to which units can be exposed for a short time, such as during transportation.

4. This corresponds only to the products with built-in cooling fan.

5. This applies only to the type with RS-485 function.

6. This functions only when the external thermal input (OH) is selected with Pr. 60 to Pr. 63 (input terminal function selection).

7. This functions only when Pr. 40 (start-time ground fault detection selection) is set to 1.

3-phase 200V

FR-S520-

0.1K

0.2K

0.4K

0.75K

1.5K

2.2K

0.1

0.2

0.4

0.75

1.5

2.2

0.3

0.5

1.0

1.6

2.8

4.0

0.8

1.4

2.5

4.1

7.0

3-phase 200 to 240V, 50/60 Hz

170 to 264V, 50/60Hz

0.4

0.7

1.2

2.1

4.0

5.5

Enclosed type (IP20) (Fully enclosed structure series is IP40)

Self-cooling

Forced cooling

0.5

0.8

0.9

1.5

Select from V/F control (Soft-PWM control/high carrier frequency PWM control selective) and automatic torque boost control

0.5 to 120Hz (starting frequency can be varied between 0 and 60Hz)

5VDC input: 1/500 of maximum setting frequency, 10VDC, DC4 to 20mA input: 1/1000 of maximum setting frequency

Digital input: 0.1Hz (less than 100Hz), 1Hz (100Hz or more)

Analog input: Within

1% of maximum output frequency (25˚C

Digital input: Within

0.5% of set output frequency (when setting dial is used)

150% (at 6Hz) during automatic torque boost control

0,0.1 to 999 s (acceleration/deceleration can be set individually), linear or S-pattern acceleration/deceleration mode can be selected

0.1K, 0.2K,

150%, 0.4K, 0.75K,

Operation frequency (0 to 120Hz), operation time (0 to 10 seconds), operation voltage (0 to 15%)

Frequency setting signal (0 to 5 (10)VDC), 4 to 20mA, digital setting with setting dial, start signal, error reset (RES), multi-speed selection

(RL, RM, RH, REX), 2nd function selection (RT), output stop (MRS), current input selection (AU), external thermal input (OH), start self-

hold selection (STOP), JOG mode selection (JOG), PID action selection (X14), PU operation/external operation changeover (X16)

Upper/lower limit frequency setting, frequency jump operation, external thermal input selection, restart after instantaneous power failure,

forward/reverse run prevention, slip compensation, operation mode selection, PID control, computer link operation (RS-485) (Note 5)

One type of open collector output can be selected from inverter running (RUN), frequency reached (SU), frequency detection (FU), overload

warning (OL), zero current detection (Y13), output current detection (Y12), PID upper limit (FUP), PID lower limit (FDN), PID forward/

reverse run (RL), READY (RY), minor failure (LF), and error (A, B, C). One type can be selected for the contact output (1 contact, 230VAC 0.3A, 30VDC 0.3A).

One type can be selected from output frequency or motor current. Pulse train output (1440 pulse/s 1mA full scale).

Overcurrent cutoff (during acceleration, deceleration, and constant speed), regenerative overvoltage cutoff (during acceleration,

deceleration, and constant speed), overload cutoff (electronic thermal relay), fin overheating, fan trouble (Note 4), stall prevention,

output side ground fault protection at starting (Note 7), external thermal input (Note 6), PU dislocation (Note 5), No. of retries exceeded,

communication error (Note 5), CPU error, undervoltage (Note 2)

–10˚C to + 50˚C(non freezing), (–10˚C to + 40˚C for fully enclosed structure specifications), 90%RH or less(non condensing)

–10˚C to + 65˚C

Indoors with no corrosive gases, flammable gases, oil mist or dust

1000m or less above sea level, 5.9m/s

3-phase 400V

FR-S540-

3.7K