Carrying The Appliance; Operation - Dyson Cinetic Big Ball Operating Manual

Emptying the clear bin and optional bin removal
Vidage du collecteur transparent et retrait du collecteur (facultatif)
Entleeren des Auffangbehälters und optionale Behälterentfernung
Het doorzichtige stofreservoir legen en het stofreservoir optioneel verwijderen
Vaciado del cubo transparente y extracción del cubo opcional
For stubborn dirt trapped in the cylinder, move mechanism up
and down until clear.
Si de la poussière tenace est coincée dans le cylindre,
déplacez le mécanisme vers le haut et le bas jusqu'à
dégagement.
Wenn sich im Zylinder hartnäckige Verschmutzungen
befinden, den Mechanismus nach oben und unten bewegen,
bis er sauber ist.
Voor hardnekkig vuil dat vast zit in de cilinder, moet u het
mechanisme omhoog en omlaag bewegen totdat het is
verwijderd.
Para eliminar la suciedad rebelde atrapada en el cilindro,
mueva el mecanismo arriba y abajo hasta que quede limpio.
In caso di sporco ostinato intrappolato nel cilindro, muovere
il meccanismo verso l'alto e il basso fino alla completa
rimozione.
Если в цилиндре осталась приставшая грязь, поднимайте
и опускайте механизм, пока она не счистится.
Za odpravljanje trdovratne umazanije, ki se ujame v cilindru,
pomikajte mehanizem navzgor in navzdol, dokler ga ne
očistite.
W przypadku uporczywego zabrudzenia znajdującego się
na kołnierzu cylindra przesuń mechanizm w górę i w dół, aż
kołnierz będzie czysty.
30 30
Come svuotare il contenitore trasparente e rimozione opzionale del contenitore
Опустошение прозрачного контейнера и снятие контейнера в случае
необходимости
Praznjenje zbiralnika smeti in izbirno odstranjevanje zbiralnika
Opróżnianie przezroczystego pojemnika i odpięcie pojemnika od cyklonów
EN
Using your Dyson appliance
Please read the 'Important Safety Instructions' in this Dyson
operating manual before proceeding.

Carrying the appliance

• Carry the appliance by the main handle.
• Do not press the cyclone release button or shake the appliance
when carrying or the cyclone could disengage, fall off and
cause injury.

Operation

• Always extend the cable fully to the red tape before use.
• Plug the appliance into the mains electricity supply.
• To switch 'ON' or 'OFF' press the red power button, located
as shown.
• After use: Unplug, push the cable retract button firmly until cable
has fully retracted.
• Switch 'OFF' the appliance and unplug before:
– Changing tools.
– Removing the hose.
Self-adjusting cleaner head with
suction control
• Your appliance has a self-adjusting cleaner head with suction
control. This cleaner head is used for testing with the European
Regulations: No. 665/2013 and No. 666/2013 and testing shall be
performed in Max mode (+).
Easy mode (-)
Reduced push force for effortless cleaning.
• For vacuuming of lightly soiled carpets, rugs and hard flooring.
• Your appliance is pre-set to this level of suction when you take it out
of the box.
Max mode (+)
Maximum suction for powerful dust and dirt removal.
• For vacuuming durable floor coverings, hard floors and heavily
soiled carpets and rugs.
• To switch to this setting, move the suction control slider on top of
the cleaner head as shown.
• CAUTION: The suction of this mode can damage delicate
flooring. Before vacuuming, check the flooring manufacturer's
cleaning recommendations.
• If the suction power of Max mode (+) prevents easy
manoeuverability, switch to Easy mode (-).
Carpets or hard floors
• The brush bar will always default to 'ON' (spinning) each time you
switch the machine 'ON'.
• To switch the brush bar 'OFF' (e.g. for delicate flooring), twist
the dial on the cleaner head a quarter of a turn. The brush bar
will stop.
• When the appliance is running and the brush bar has been
switched 'OFF', the brush bar can be switched 'ON' again by
twisting the dial on the cleaner head a quarter of a turn. The brush
bar will start. Alternatively, switch the appliance 'OFF'; the dial will
return to its original position. When the appliance is switched 'ON'
again the brush bar starts automatically.
• The brush bar can only be turned off once the machine is running.
• The brush bar will automatically stop if it becomes
obstructed. See 'Brush bar – clearing obstructions'.
• Before vacuuming your flooring, rugs and carpets, check the
manufacturer's recommended cleaning instructions.
• Some carpets may fuzz if a rotating brush bar is used when
vacuuming. If this happens, we recommend vacuuming
with the brush bar switched 'OFF' and consulting with the
carpet manufacturer.
• The brush bar on the appliance may damage some carpet types.
If you are unsure, turn 'OFF' the brush bar.
• This product has carbon fibre brushes. Take care if coming
into contact with them, as they may cause minor skin irritation.
Wash your hands after handling the brushes.
• Check the brush bar regularly and clear away any debris (such as
hair). Debris left on the brush bar may cause damage to flooring
when vacuuming.
Vacuuming
• Do not use without the clear bin and cyclone in place.
• Do not use on rubble, ash or plaster. This appliance is designed
only for domestic use to remove household dirt, hair and allergens.
The appliance is not designed to be used on:
– debris produced from activities such as DIY, building or
similar tasks
– larger types and quantities of dust or debris, such as soot
and sawdust.
These materials may harm the appliance and may void
your guarantee.
• Fine dirt such as flour should only be vacuumed in very
small amounts.
• Do not use the appliance to pick up sharp hard objects, small toys,
pins, paper clips, etc. They may damage the appliance.
• When vacuuming, certain carpets may generate small static
charges in the clear bin or wand. These are harmless and are
not associated with the mains electricity supply. To minimize any
effect from this small static charge, do not put your hand or insert
any object into the clear bin unless you have emptied it first, then
cleaned it with a damp cloth (see 'Cleaning the clear bin').
• Do not work with the appliance above you on the stairs.
• Do not put the appliance on chairs, tables, etc.
• Before vacuuming highly polished floors, such as wood or lino, first
check that the underside of the floor tool and its brushes are free
from foreign objects that could cause marking.
• Do not push hard with the floor tool when vacuuming, as this may
cause damage.
Blockages – thermal cut-out
• This appliance is fitted with an automatically resetting thermal
cut-out.
• If any part becomes blocked the appliance may overheat and
automatically cut-out.
• If this happens, follow the instructions in 'Looking for blockages'.
• NOTE: Large items may block the tools or wand inlet. If this
happens, do not operate the wand release catch. Switch 'OFF' and
unplug. Failure to do so could result in personal injury.
31