Listening To A Program Source - Sherwood RD-7103 Operation Instructions Manual

O O p p e e r r a a t t i i o o n n s s

LISTENING TO A PROGRAM SOURCE

B B e e f f o o r r e e o o p p e e r r a a t t i i o o n n
Enter the standby mode.
The STANDBY indicator lights up.
This means that the receiver is not disconnected from
the AC mains and a small amount of current is retained
to support the memorized contents and operation
readiness.
To switch the power completely off, push the POWER
switch again.
The power is cut off and the STANDBY indicator
goes off.
In the standby mode, turn the power on.
1
STANDBY
ON/STANDBY
or
Each time the STANDBY button on the front panel
or the POWER button on the remote control is
pressed, the receivers turns on to enter the operating
mode or off to enter the standby mode.
In the standby mode, if the INPUT SELECTOR
button is pressed, the receiver turns on
automatically and the desired input is selected.
Switch the speakers on.
2
The SPEAKER indicator lights up and sound can
be heard from the speakers connected to the speaker
terminals.
When using headphones for private listening, press
the SPEAKER button again to switch the speakers
off.
MAIN POWER
ON/ OFF
POWER P .SCAN
POWER
1 2 3 4 5
6 7 8 9 0
DISC
CD
REPEAT INTRO
A B < <
A
DECK SEL.
B DECK
PRESET USER FILE T .MON DISPLAY
CD TUNER VIDEO1 EQUALIZER
AUX TAPE MON. VIDEO2 STEREO
6CH DIRECT VIDEO3 AUTO DSP MODE
INPUT
SELECTOR
T .TONE CH SEL.
D.TIME ADJUST
CH LEVEL MASTER
DISPLAY SLEEP MUTE
SYS
SPEAKER
ON/OFF
Select the desired input source.
3
INPUT SELECTOR
AUDIO VIDEO TAPE MON.
Each time the "AUDIO" button is pressed, the input
source changes as follows;
→ TUNER → CD → AUX
(frequency display)
Each time the "VIDEO" button is pressed, the input
source changes as follows;
→ VIDeo 1 → VIDeo 2 → VIDeo 3
When the TAPE MONITOR button is set to on so that
"TAPE M" indicator lights up, other inputs can not be
heard from the speakers.
To listen to an input source other than TAPE MONITOR,
be sure to set the TAPE MONITOR button to off.
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer to
the receiver's TAPE MONITOR jacks.
To listen to the component connected to these jacks, set the
TAPE MONITOR button to on.
If you connect a 3-head tape deck, you can monitor the actual
recording, not the source sound.
For further details, refer to the operating instructions of the
component connected.
When selecting the 6 CH DIRECT as desired,
6CH DIRECT
or
6-DIRECT is displayed and the 6 separate analog
signals from a decoder or DVD player connected to
this unit will be heard. You can use the tone controls
and volume control to adjust the signal. (If the TAPE
MONITOR button is set to on, it will be automatically
set to off.)
To cancel the 6 DIRECT function, press the 6 CH
DIRECT button again or select another desired input
source.
These 6 separate analog signals can be heard, only.
They cannot be recorded.
11
POWER P .SCAN
1 2 3 4 5
6 7 8 9 0
CD TUNER VIDEO1 DISC
CD
REPEAT INTRO
A < < B
A
DECK SEL.
B DECK
AUX TAPE MON. VIDEO2
PRESET USER FILE T .MON DISPLAY
CD TUNER VIDEO1 EQUALIZER
AUX TAPE MON. VIDEO2 STEREO
or
6CH DIRECT VIDEO3 AUTO DSP MODE
INPUT
SELECTOR
VIDEO3 T .TONE CH SEL.
D.TIME ADJUST
CH LEVEL MASTER
DISPLAY SLEEP MUTE
SYS
POWER P .SCAN
1 2 3 4 5
6 7 8 9 0
DISC
CD
REPEAT INTRO
< <
A B
A
DECK SEL.
B DECK
PRESET USER FILE T .MON DISPLAY
CD TUNER VCR 1 EQUALIZER
AUX TAPE MON. VCR 2
STEREO
6CH DIRECT DVD/TV DSP MODE
INPUT
SELECTOR
T .TONE CH SEL.
6CH DIRECT
D.TIME ADJUST
CH LEVEL MASTER
DISPLAY SLEEP MUTE
SYS