Listening To A Program Source - Sherwood RVD-8090R Operating Instructions Manual

LISTENING TO A PROGRAM SOURCE

Before operation
Enter the standby mode.
The STANDBY indicator lights up.
The receiver remains connected to
the AC main electrical supply and a small amount
of current is retained to support the on-board
memory and rapid turn-on.
To switch the power off, push the POWER switch
again.
Then the power is cut off and the STANDBY
indicator goes off.
In the standby mode, turn the power on.
1
STANDBY
Each time the STANDBY button on the front panel or
the POWER button on the remote control is pressed,
the receiver turns on and enters the operating mode or
turns off to enter the standby mode.
In the standby mode, pressing any INPUT
SELECTOR button automatically turns the receiver
on and selects the desired input.
Switch the speakers on.
2
The SPEAKER indicator will light up and sound
can be heard from the speakers connected to the
receiver's speaker terminals.
When using the headphone for private listening,
press the SPEAKER button again to turn the
speakers off.
POWER
ON/OFF
POWER
POWER P.SCAN
1 2 3 4 5
6 7 8 9 0
DISC
CD REPEAT INTRO
A B SCAN
CD TUNER DECK SEL
A B
AUX TAPE MON.
DVD/TV
VCR1 VCR2
6 CH DIRECT
or EQ DECK
PRESET USER FILE DISPLAY T.MON
DSP STEREO
MODE
CHANNEL T.TONE D.TIME ADJUST
SEL
CHANNEL LEVEL MASTER VOLUME
DISPLAY SLEEP MUTE
SYS
REMOTE CONTROL RM-RVD-98LM
SPEAKER
Select the desired input source.
3
INPUT SELECTOR
AUDIO
TAPE
MONITOR
VIDEO
Each time the "AUDIO" button is pressed, the input
source changes as follows;
TUNER
(frequency display)
Each time the "VIDEO" button is pressed, the input
source changes as follows;
VCR1 VCR2
When the TAPE MONITOR button is set to on, the
"TAPE M" indicator lights up and the source connected
to the TAPE MONITOR input can be heard. To listen
to a source other than the one connected to the TAPE
MONITOR, be sure the TAPE MONITOR is set to off.
TAPE MONITOR function
Either a tape deck or a graphic equalizer can be connected
to the receiver's TAPE MONITOR jacks. To listen to the
component connected to these jacks, press the TAPE
MONITOR button to on.
If a 3-Head tape deck is connected to the TAPE
MONITOR jacks, you can listen to the sound directly from
the tape while it is being recorded and not the source.
For further details, refer to the operating instructions of the
component connected to these jacks.
The 6 CH DIRECT INPUT
Use this input to listen to the audio output of an external
decoder or a DVD player with built-in 6 channel decoder.
6 CHANNEL
DIRECT
or
"6-DIRECT" is displayed and the 6 separate analog
signals from 6 CH decoder connected to this unit pass
through the tone (bass, treble) and volume circuits only
and directly transfer to the speakers. (If the TAPE
MONITOR button is set to on, the TAPE MONITOR
button will automatically be set to off.)
To cancel the 6 CH direct function, press the 6 CH
DIRECT button again or select the desired input source.
These 6 separate analog signals can be heard only. They
cannot be recorded.
14
POWER P.SCAN
1 2 3 4 5
6 7 8 9 0
DISC
CD REPEAT INTRO
A B SCAN
CD TUNER DECK SEL
CD TUNER A B
AUX TAPE MON.
DVD/TV
VCR1 VCR2
6 CH DIRECT
EQ DECK
PRESET USER FILE DISPLAY T.MON
AUX TAPE MON.
DSP STEREO
MODE
or
CHANNEL T.TONE D.TIME ADJUST
SEL
CHANNEL LEVEL MASTER VOLUME
DISPLAY SLEEP MUTE
DVD/TV
SYS
REMOTE CONTROL RM-RVD-98LM
VCR1 VCR2
CD AUX
DVD
POWER P.SCAN
1 2 3 4 5
6 7 8 9 0
DISC
CD REPEAT INTRO
A B SCAN
CD TUNER DECK SEL
A B
6 CH DIRECT AUX TAPE MON.
DVD/TV
VCR1 VCR2
6 CH DIRECT
DECK
EQ
PRESET USER FILE DISPLAY T.MON
DSP STEREO
MODE
CHANNEL T.TONE D.TIME ADJUST
SEL
CHANNEL LEVEL MASTER VOLUME
DISPLAY SLEEP MUTE
SYS
REMOTE CONTROL RM-RVD-98LM