Checking The Size Of A Loaded Original; G Manually Setting The Scanning Size; Manually Setting The Scanning Size - Sharp AR-M355N Operation Manual

CHECKING THE SIZE OF A LOADED ORIGINAL

When a standard-size* original is placed, the original size is automatically detected
(automatic original detection function) and displayed in the top half of the [ORIGINAL]
key. Check the key to make sure that the original size has been correctly detected.
:[AUTO] appears when the automatic original detection function is operating.
:Displays the original size.
If a non-standard size original is placed or if you wish to change the scanning size,
follow the steps below to manually set the original scanning size.
NOTE
* Standard sizes that can be detected are as follows:
5-1/2"x8-1/2", 8-1/2"x11", 8-1/2"x11"R, 8-1/2"x14", 11"x17", A5, B5, B5R, A4, A4R, B4, A3. If a non-standard
size original is loaded (including special sizes), the closest standard size may be displayed, or the original size
may not appear at all.

MANUALLY SETTING THE SCANNING SIZE

If you load an original that is not a standard size (such as an AB size), or if the size is not detected correctly, you must
touch the [ORIGINAL] key and set the original size manually. Perform the following steps after loading the document
in the automatic document feeder or on the document glass.
1 Touch the [ORIGINAL] key.
STANDARD
RESOLUTION
AUTO 8 X11 1 /
2
ORIGINAL
2 Touch the key under [SCAN SIZE].
SPEAKER
SCAN SIZE SEND SIZE
100%
AUTO 8 X11 1 / AUTO
2
2-SIDED 2-SIDED
BOOKLET TABLET
3 Touch the desired original size key.
SPEAKER RESEND
OK
1 /
5 X8 1 / 1 / 8 X13
2 2 2
AB
5 X8 R 1 / 1 / 8 X14 1 /
2 2 2
INCH
8 X11 1 / 11X17
2
8 X11R 1 /
LONG SIZE
2
STANDARD SIZE
SIZE INPUT
If you wish to select an AB size, touch the
[AB/INCH] key and then touch the desired
original size key.
SPEAKER RESEND
OK
8 X11 1 /
2 A5 A5 A4
AB
AUTO
A5R A4R
INCH
MANUAL
B5 B4
B5R A3
LONG SIZE
STOM
ZE
STANDARD SIZE SIZE INPUT
1-8
If the address book screen
appears, touch the
[CONDITION SETTINGS]
key to display the
condition settings screen
(page 1-5).
[AUTO] is no longer
highlighted. [MANUAL]
and the original size key
you touched are
highlighted.
If you placed a long original,
touch the key.
LONG SIZE
[AB] is highlighted and
AB size keys are
displayed. To return to
the inch palette, touch
the [AB/INCH] key once
again.
If you placed a non-standard size original
on the document holder or on the
document glass, touch the [SIZE INPUT]
tab and then enter the width (X) and length
(Y) of the original with the
X
OK
A
Y
(2 1/2 17)
17
X
inch
(2 1/2 11 5/8)
Y 11
inch
STANDARD SIZE SIZE INPUT
If you frequently send documents that are the same non-
standard size, you can store the dimensions as explained
in "STORING, DELETING, AND USING ORIGINAL
SIZES" on the following page. This will allow you to omit
entry of X and Y each time you send that size of document.
4 Touch the outer [OK] key.
Touch the [OK] key to return to the screen of step 2.
5 Touch the outer [OK] key.
SPEAKER RESEND
OK
SEND SIZE
AUTO
-SIDED
6 The selected size appears in the top half of
the [ORIGINAL] key.
STANDARD
RESOLUTION
A4
ORIGINAL
STANDARD
RESOLUTION
AUTO 8 X11 1 /
2
ORIGINAL
keys.
X (width) is initially selected.
Enter X and then touch the Y
( ) key to enter Y. A width of
2-1/2 to 17 inch (64 to 432 mm)
can be entered in X, and a
length of 2-1/2 to 11-5/8 inch (64
to 297 mm) can be entered in Y.