Disabling Switching Of Display Order; Disabling Of Clock Adjustment; Device Control; Original Size Detector Setting - Sharp AR-M351N Key Operator's Manual

Disabling switching of display order

This program is used to disable the function that
changes the display order of tabs when a selected tab
is touched repeatedly in screens that have tabs such
as the custom folder selection screen and folder
selection screen of the document filing function and the
address book screen of fax/image send mode.

Disabling of clock adjustment

This program is used to prohibit changes to the clock
adjust setting. When the program is enabled, "Clock" in
the custom settings cannot be used. To adjust the date
and time, this program must first be disabled (remove
the checkmark).

Device control

Use these programs when a peripheral device on the
machine has failed or when you wish to temporarily
disable a device. The programs can also be used to
change the function setting of a device as required by
your conditions of use.
"Device control" consists of the following programs:
G Original size detector setting
G Disabling of document feeder
G Disabling of duplex
G Disabling of stapler
G Disabling of punch
G Disabling of optional paper drawer
G Disabling of finisher
G Disabling of mail-bin stacker
G Disabling of covers/inserts mode
G Saddle stitch position adjust
G High speed stacking
G Rotated output
G Auto paper selection setting
G Optimization of a hard disk

Original size detector setting

This program is used to select the standard original
sizes that can be detected by the original size detection
function. Select one of the four groups indicated below.
The factory default setting is "AB-1 (INCH-1)". Original
size detection by the document glass can also be
disabled.
Detectable original sizes
Document feeder tray (for automatic
Group
document feeder)
Document glass
11" x 17", 8-1/2" x 14",
8-1/2" x 11",
1 INCH-1
8-1/2" x 11"R,
5-1/2" x 8-1/2"
11" x 17", 8-1/2" x 13",
8-1/2" x 11",
2 INCH-2
8-1/2" x 11"R,
5-1/2" x 8-1/2"
A3, A4, A4R, A5,
3 AB-1
B4, B5, B5R
A3, A4, A4R, A5,
4 AB-2
B5, B5R, 216x330
If "CANCEL DETECTION AT DOCUMENT GLASS" is
set, originals will be regarded as EXTRA for all copier
functions and no original size will be displayed.

Disabling of document feeder

This program is used to prevent use of the reversing
automatic document feeder when it malfunctions. In
this case, scanning can still be performed using the
document glass.

Disabling of duplex

This program is used to disable duplex printing when
the duplex module malfunctions. If this program is set,
only one-sided printing can be performed.

Disabling of stapler

This program is used to disable stapling when the
stapler unit of the finisher or the saddle stitch finisher
malfunctions.

Disabling of punch

Use this program when you wish to prohibit punching
or when the punch unit of the finisher or saddle stitch
finisher has failed.

Disabling of optional paper drawer

This program is used to disable use of the stand/3 x
500 sheet paper drawer or stand/MPD & 2000 sheet
paper drawer when it malfunctions.

Disabling of finisher

Use this program when you wish to prohibit use of the
finisher or saddle stitch finisher, or when either has
failed.

Disabling of mail-bin stacker

This program is used to disable use of the mail-bin
stacker when it malfunctions.

Disabling of covers/inserts mode

Use this program when you wish to prohibit use of the
covers/inserts mode.
GENERAL PROGRAMS
A3, A4
A3, A4
11" x 17", 8-1/2"
x 11",
216x330
11" x 17", 8-1/2"
x 11", B4
11