I/O Signal List; Remote Register - Mitsubishi Electric A800-E Instruction Manual

I/O signal list
 When Pr.544 = "0" (compatible with CC-Link Ver.1)
• Remote I/O (32 points)
Device
Signal
No.

RYn0 Forward rotation command
RYn1 Reverse rotation command
High-speed operation command
RYn2
(terminal RH function)
Middle-speed operation command
RYn3
(terminal RM function)
Low-speed operation command
RYn4
(terminal RL function)
Jog operation command
RYn5
(terminal Jog function)
Second function selection
RYn6
(terminal RT function)
Current input selection
RYn7
(terminal AU function)
Selection of automatic restart after
RYn8 instantaneous power failure
(terminal CS function)
RYn9 Output stop (terminal MRS function)
Start self-holding selection
RYnA
(terminal STOP function)
RYnB Reset (terminal RES function)
RYnC Monitor command
RYnD Frequency setting command (RAM)
Frequency setting command (RAM,
RYnE
EEPROM)
RYnF Instruction code execution request
RY(n+1)0
to Reserved
RY(n+1)7
Not used
RY(n+1)8
(initial data process completion flag)
Not used
RY(n+1)9
(initial data process request flag)
RY(n+1)A Error reset request flag
RY(n+1)B
to Reserved
RY(n+1)F

These signals are set in the initial status. Using Pr.180 to Pr.189, you can change input signal functions.
Refer to the Instruction Manual (Detailed) of the FR-A800/FR-F800 inverter for details of Pr.180 to Pr.189.

For the FR-F800-E, no function is assigned in the initial setting.

The signals are fixed. They cannot be changed using parameters.

These signals are set in the initial status. Using Pr.190 to Pr.196, you can change output signal functions.
Refer to the Instruction Manual (Detailed) of the FR-A800/FR-F800 inverter for details of Pr.190 to Pr.196.

Output signal can be assigned using Pr.313 to Pr.315. The setting range depends on the inverter. For details, refer to the description of Pr.190
to Pr.196 (Output terminal function selection) in the Instruction Manual (Detailed) of the FR-A800/FR-F800 inverter.

"n" indicates a value determined according to the station number setting.

• Remote register

Description
Address

Upper 8 bits
RWwn Monitor code 2
Set frequency (0.01 Hz increments) /
RWwn+1
torque command
RWwn+2 H00 (arbitrary)

RWwn+3 Write data

The above 8 bit is always H00 even if a value other than H00 is set.

For the FR-A800-E, when Pr.804="3 or 5" during torque control under Real sensorless vector control or vector control, a torque command value
is set in RWwn+1.

"n" indicates a value determined according to the station number setting.
Refer to
page
56

56

56

56

56

56

56

56

56
,
 
56

56

56

56
56
56
56
—
—
—
56
—
Refer to
Lower 8 bits page
Monitor code 1 58
58

Instruction code 58
58
(N) Operation via communication and its settings
Device
No.

RXn0 Forward running
RXn1 Reverse running
RXn2 Running (terminal RUN function)
RXn3 Up to frequency (terminal SU function)
RXn4 Overload alarm (terminal OL function)
Instantaneous power failure
RXn5
(terminal IPF function)
Frequency detection
RXn6
(terminal FU function)
RXn7 Error (terminal ABC1 function)
RXn8 — (terminal ABC2 function)
RXn9 Pr.313 assignment function (DO0)
RXnA Pr.314 assignment function (DO1)
RXnB Pr.315 assignment function (DO2)
RXnC Monitoring
RXnD Frequency setting completion (RAM)
Frequency setting completion (RAM,
RXnE
EEPROM)
RXnF Instruction code execution completion
RX(n+1)0
to Reserved
RX(n+1)7
Not used
RX(n+1)8
(initial data process request flag)
Not used
RX(n+1)9
(initial data process completion flag)
RX(n+1)A Error status flag
RX(n+1)B Remote station ready
RX(n+1)C
to Reserved
RX(n+1)F
Address

RWrn First monitor value
RWrn+1 Second monitor value
RWrn+2 Reply code
RWrn+3 Read data
Refer to
Signal
page
57
57
57

57

57

57

57

57

57

57

57

57

57
57
57
57
—
—
—
57
57
—
Refer to
Description
page
59
59
59
59
PARAMETER
2
GROUP
N
53