Control Change - Roland V-Combo VR-760 Owner's Manual

MIDI Implementation
Data set 1 DT1
This is the message that actually performs data transmission, and is used when you wish to
transmit the data.
Status Data byte
F0H 41H, dev, 00H, 5FH, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H - 1FH, 7FH, Initial value is 10H)
00H Model ID #1 (VR-760)
5FH Model ID #2 (VR-760)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of the data to be sent
bbH Address: upper middle byte of the starting address of the data to be sent
ccH Address: lower middle byte of the starting address of the data to be sent
ddH Address LSB: lower byte of the starting address of the data to be sent.
eeH Data: the actual data to be sent. Multiple bytes of data are transmitted in
order starting from the address.
: :
ffH Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the address
and size given in "Parameter Address Map" (p. 109).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to p. 112.
106
2. Data Transmission
Status
F7H
Status
8nH
n = MIDI channel number:
kk = note number:
vv = note off velocity:
* Note off message on the Organ Part is sent out with the velocity of 40H.
Status
9nH
n = MIDI channel number:
kk = note number:
vv = note on velocity:
* Note on message on the Organ Part is sent out with the velocity of 64H.
Status
BnH
BnH
n = MIDI channel number:
mm, ll = Bank number:
Status
BnH
n = MIDI channel number:
vv = Modulation depth:
Status
BnH
n = MIDI channel number:
vv = Portamento Time:
Status
BnH
n = MIDI channel number:
vv = Volume:
Status
BnH
n = MIDI channel number:
vv = Expression:
* These messages are transmitted when the Piano Exp Sw
Status
BnH
n = MIDI channel number:
vv = Control value:
* Depending on the Control Message settings (Edit: System MIDI: Control Message).
Status
BnH
n = MIDI channel number:
vv = Control value:
* Depending on the Control Message settings (Edit: System MIDI: Control Message).
Channel Voice Messages
Note off
2nd byte
kkH
Note on
2nd byte
kkH

Control Change

Bank Select (Controller number 0, 32)
2nd byte
00H
20H
Modulation (Controller number 1)
2nd byte
01H
Portamento Time (Controller number 5)
2nd byte
05H
Volume (Controller number 7)
2nd byte
07H
Expression (Controller number 11)
2nd byte
0BH
(EDIT: System Basic: Piano Exp Sw) is ON.
General Purpose Controller 1 (Controller number 16)
2nd byte
10H
General Purpose Controller 2 (Controller number 17)
2nd byte
11H
3rd byte
40H
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
01H - 7FH (1 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
01H - 7FH (1 - 127)
3rd byte
mmH
llH
0H - FH (ch.1 - 16)
00 00H - 7F 7FH (bank.1 - bank.16384)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)