Roland V-Combo VR-760 Owner's Manual page 92

Effects/Parameter List
6: ENHANCER
Controls the overtone structure of the high frequencies, adding
sparkle and tightness to the sound.
Parameter Value
Sens # 0–127
Mix # 0–127
Low Gain -15–+15 dB
High Gain -15–+15 dB
Level 0–127
7: AUTO WAH
Cyclically controls a filter to create cyclic change in timbre.
Parameter Value
Filter LPF, BPF
Sens 0–127
Manual # 0–127
Peak 0–127
Rate # 0.05–10.00 Hz
Depth 0–127
Level 0–127
8: ROTARY
The Rotary effect simulates the sound of the rotary speakers often
used with the electric organs of the past. Since the movement of the
high range and low range rotors can be set independently, the
unique type of modulation characteristic of these speakers can be
simulated quite closely. This effect is most suitable for electric organ
Patches.
Parameter Value
Low Slow 0.05–10.00 Hz
Low Fast 0.05–10.00 Hz
Low Accel 0–15
Low Level 0–127
Hi Slow 0.05–10.00 Hz
Hi Fast 0.05–10.00 Hz
Hi Accel 0–15
Hi Level 0–127
Separate 0–127
Speed # SLOW, FAST
Level # 0–127
92
Explanation
Sensitivity of the enhancer
Level of the overtones generated by the
enhancer
Gain of the low range
Gain of the high range
Output Level
Explanation
Type of filter
LPF: The wah effect will be applied
over a wide frequency range.
BPF: The wah effect will be applied
over a narrow frequency range
Adjusts the sensitivity with which the
filter is controlled.
Adjusts the center frequency at which
the effect is applied.
Adjusts the amount of the wah effect
that will occur in the range of the center
frequency.
Set a higher value for Q to narrow the
range to be affected.
Frequency of modulation
Depth of modulation
Output Level
Explanation
Slow speed (SLOW) of the low frequen-
cy rotor
Fast speed (FAST) of the low frequency
rotor
Adjusts the time it takes the low fre-
quency rotor to reach the newly selected
speed when switching from fast to slow
(or slow to fast) speed. Lower values
will require longer times.
Volume of the low frequency rotor
Settings of the high frequency rotor
The parameters are the same as for
the low frequency rotor
Spatial dispersion of the sound
Simultaneously switch the rotational
speed of the low frequency rotor and
high frequency rotor.
SLOW: Slows down the rotation to
the Slow Rate.
FAST: Speeds up the rotation to the
Fast Rate.
Output Level
9: COMPRESSOR
Flattens out high levels and boosts low levels, smoothing out
unevenness in volume.
Parameter Value
Attack 0–127
Sustain 0–127
Post Gain 0, +6, +12, +18 dB
Low Gain -15–+15 dB
High Gain -15–+15 dB
Pan # L64–63R
Level # 0–127
10: LIMITER
Compresses signals that exceed a specified volume level, preventing
distortion from occurring.
Parameter Value
Threshold 0–127
Ratio 1.5:1, 2:1, 4:1, 100:1
Release 0–127
Post Gain 0, +6, +12, +18 dB
Low Gain -15–+15 dB
High Gain -15–+15 dB
Pan # L64–63R
Level # 0–127
11: HEXA-CHORUS
Uses a six-phase chorus (six layers of chorused sound) to give
richness and spatial spread to the sound.
Parameter Value
Pre Delay 0.0–100.0 ms
Rate # 0.05–10.00 Hz
Depth 0–127
Delay Dev 0–20
Depth Dev -20–+20
Pan Dev 0–20
Balance # D100:0W–
D0:100W
Level 0–127
12: TREMOLO CHO (Tremolo Chorus)
This is a chorus effect with added Tremolo (cyclic modulation of
volume).
Parameter Value
Pre Delay 0.0–100.0 ms
Cho Rate 0.05–10.00 Hz
Cho Depth 0–127
Phase 0–180˚
Trem Rate # 0.05–10.00 Hz
Trem Sep 0–127
Balance # D100:0W–D0:100W
Level 0–127
Explanation
Attack time of an input sound
Adjusts the time over which low lev-
el sounds are boosted until they
reach the specified volume.
Adjusts the output gain.
Gain of the low range
Gain of the high range
Stereo location of the output sound
Output Level
Explanation
Adjusts the volume at which com-
pression will begin.
Compression ratio
Adjusts the time from when the vol-
ume falls below the Threshold Lev-
el until compression is no longer
applied.
Adjusts the output gain.
Gain of the low range
Gain of the high range
Stereo location of the output sound
Output Level
Explanation
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Frequency of modulation
Depth of modulation
Adjusts the differences in Pre Delay be-
tween each chorus sound.
Adjusts the difference in modulation
depth between each chorus sound.
Adjusts the difference in stereo location
between each chorus sound.
0: All chorus sounds will be in the
center.
20: Each chorus sound will be spaced
at 60 degree intervals relative to the
center.
Volume balance between the direct
sound (D) and the chorus sound (W)
Output Level
Explanation
Adjusts the delay time from the di-
rect sound until the chorus sound
is heard.
Modulation frequency of the cho-
rus effect
Modulation depth of the chorus ef-
fect
Spread of the tremolo effect
Modulation frequency of the trem-
olo effect
Spread of the tremolo effect
Volume balance between the direct
sound (D) and the tremolo chorus
sound (W)
Output Level