Page 1
Sat. 8 a.m.–4 p.m. MST ON THE WEB: www.proformservice.com CAUTION Visit our website at Read all precautions and instruc- www.proform.com tions in this manual before using this equipment. Keep this manu- new products, prizes, al for future reference. fitness tips, and much more!
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on the vibration platform before using the vibration platform. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
Page 4
14. To purchase a surge suppressor, use and before cleaning the vibration plat- see your local PROFORM dealer or call the form. Servicing other than the procedures in telephone number on the front cover of this...
BEFORE YOU BEGIN Thank you for selecting the revolutionary PROFORM tacting us. The model number and the location of the ® ACTIVATOR V5 vibration platform. The ACTIVATOR serial number decal are shown on the front cover of V5 vibration platform offers whole body vibration this manual.
PART IDENTIFICATION CHART See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST near the end of this manual. Note: Some small parts may have been preattached.
ASSEMBLY • For help identifying small parts, see the PART Make Assembly Easier IDENTIFICATION CHART on page 6. This manual is designed to ensure that the • Tighten all parts as you assemble them, unless vibration platform can be assembled successful- instructed to do otherwise.
Page 8
2. Tip: Be careful not to pinch the wires during this step. With the help of a second person, carefully tip the Base (5) onto its side. Attach the Lower Upright (1) to the Base (5) with two M10 x 55mm Patch Screws (20), two M10 Split Washers (38), two M10 x 68mm Bolts (44), and two M10 Nylon Locknuts (32).
Page 9
5. Have a second person hold the Upper Upright (36) near the Lower Upright (1). See the inset drawing. Locate the wire tie in the Upper Upright (36). Tie the lower end of the wire tie to the Wire Harness (43) as shown. Then, pull the upper end of the wire tie until the Wire Harness is routed through the Upper Upright.
Page 10
8. Remove the four M4 x 12mm Self-tapping Screws (27) from the back of the Console (3). Set the Self-tapping Screws aside until step 9. Attach the back of the Console (3) to the Upper Upright (36) with two M4 x 16mm Patch Screws (26).
Page 11
11. Tip: Be careful not to pinch the wires during this step. Attach the front of the Console (3) to the back of the Console with the four M4 x 12mm Self- tapping Screws (27) you removed in step 8 and an M4 x 19mm Screw (45).
HOW TO USE THE VIBRATION PLATFORM HOW TO MOVE THE VIBRATION PLATFORM Handlebar Before moving the vibration platform, unplug the power cord. Hold the handlebar and place one foot against the wheel. Tilt the vibration platform until it rolls freely on the wheel.
Page 13
Grounded Outlet Box form (see drawing 1 at the right). To purchase a Adapter surge suppressor, see your local PROFORM dealer Surge Suppressor or call the telephone number on the front cover of this manual and order part number 146148, or see your local electronics store.
Page 14
CONSOLE DIAGRAM CONSOLE FEATURES you do not do this, the console or other electronic components may become damaged. The console offers a selection of features designed to make your workouts more effective and enjoyable. Plug the power cord You can change the time and frequency of your vibra- into the receptacle on tion sessions with the touch of a button.
Page 15
HOW TO USE THE MANUAL MODE HOW TO USE AN IFIT PROGRAM 1. Turn on the power. 1. Turn on the power. See HOW TO TURN ON THE POWER on page See HOW TO TURN ON THE POWER on page 2.
TROUBLESHOOTING Inspect all parts of the vibration platform regularly. Replace any worn parts immediately. Outer surfaces of the vibra- tion platform can be cleaned with a damp cloth and a mild, non-abrasive detergent; do not use solvents to clean the vibration platform. Most vibration platform problems can be solved by following the simple steps below.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us: • the model number and serial number of the product (see the front cover of this manual) •...