Table of Contents
Advertisement
GAGGIA VELASCA
1.5 Page 4 (EV - PUMP)
Should this page been shown it means either the dreg drawer is not cor-
rectly inserted or the side door not closed. Only solving both these issues
it would be possible to come out from this screen.
Press the ESPRESSO button to activate the 2-ways Electrovalve (closed by default)
The Electrovalve is activated so the EV1 value turns from "OFF" to "ON".
Press the HOT WATER (Press MILK for OTC version) button to activate the Pump
The water now flows out from the spout, causing the update of the IMP
value with the number of flowmeter impulses. The L/H value must stay
within 10l/h and 18 l/h.
ERROR:
If the number of impulses remains 0 and the display backlight turns red,
it means that there's an error in the hydraulic circuit. If water comes out
from the spout it means that there's an error in the flowmeter or in its
wiring to the CPU/POWER (JP5); if, on the other hand, no water comes
out it's necessary to check the pump or the hydraulic circuit, or the pump
wiring (JP24).
Press the STEAM WATER button (Press CAPPUCCINO for OTC version)
The CA shows the Heater/Grinder page (Heater-Grinder)
1.6 Page 5 (Heater-Grinder)
Initial condition
Press the HOT WATER (Press MILK for OTC version) button to activate the Grinder
The coffee grinder starts milling for 5000 ms. In this case the activation
time is shown in the red-circled field of the picture
ERROR:
If this number keeps fixed at 0,or the grinder does not run, the display
turns red: this means there must be a fault in the grinder wiring (JP8), or
in the grinder itself, or in the electronic board.
Keep pressed STANDBY for 5 secs to reset grinder parameters
Pressing button STANDBY for 5 secs resets grinder parameters:
This action is needed if the grinder has been replaced.
1.5 Page 4 (EV - PUMP)
1.5 Page 4 (EV - PUMP)
1.5 Page 4 (EV - PUMP)
Should this page been shown it means either the dreg drawer is not
Should this page been shown it means either the dreg drawer is not
correctly inserted or the side door not closed. Only solving both these
Should this page been shown it means either the dreg drawer is not
correctly inserted or the side door not closed. Only solving both these
1.5 Page 4 (EV - PUMP)
issues it would be possible to come out from this screen.
correctly inserted or the side door not closed. Only solving both these
issues it would be possible to come out from this screen.
1.5 Page 4 (EV - PUMP)
issues it would be possible to come out from this screen.
Should this page been shown it means either the dreg drawer is not
correctly inserted or the side door not closed. Only solving both these
Should this page been shown it means either the dreg drawer is not
issues it would be possible to come out from this screen.
correctly inserted or the side door not closed. Only solving both these
issues it would be possible to come out from this screen.
Press the ESPRESSO button to activate the 2-ways Electrovalve (closed by default)
Press the ESPRESSO button to activate the 2-ways Electrovalve (closed by default)
The Electrovalve is activated so the EV1 value turns from "OFF" to
Press the ESPRESSO button to activate the 2-ways Electrovalve (closed by default)
The Electrovalve is activated so the EV1 value turns from "OFF" to
"ON".
The Electrovalve is activated so the EV1 value turns from "OFF" to
"ON".
"ON".
Press the ESPRESSO button to activate the 2-ways Electrovalve (closed by default)
The Electrovalve is activated so the EV1 value turns from "OFF" to
Press the ESPRESSO button to activate the 2-ways Electrovalve (closed by default)
"ON".
The Electrovalve is activated so the EV1 value turns from "OFF" to
"ON".
1.5 Page 4 (EV - PUMP)
The water now flows out from the spout, causing the update of the
Should this page been shown it means either the dreg drawer is not
The water now flows out from the spout, causing the update of the
IMP value with the number of flowmeter impulses. The L/H value
correctly inserted or the side door not closed. Only solving both these
The water now flows out from the spout, causing the update of the
IMP value with the number of flowmeter impulses. The L/H value
must stay within 10l/h and 18 l/h.
issues it would be possible to come out from this screen.
IMP value with the number of flowmeter impulses. The L/H value
must stay within 10l/h and 18 l/h.
must stay within 10l/h and 18 l/h.
The water now flows out from the spout, causing the update of the
The water now flows out from the spout, causing the update of the
IMP value with the number of flowmeter impulses. The L/H value
IMP value with the number of flowmeter impulses. The L/H value
must stay within 10l/h and 18 l/h.
must stay within 10l/h and 18 l/h.
ERROR:
ERROR:
If the number of impulses remains 0 and the display backlight turns
Press the ESPRESSO button to activate the 2-ways Electrovalve (closed by default)
ERROR:
If the number of impulses remains 0 and the display backlight turns
red, it means that there's an error in the hydraulic circuit. If water
The Electrovalve is activated so the EV1 value turns from "OFF" to
If the number of impulses remains 0 and the display backlight turns
red, it means that there's an error in the hydraulic circuit. If water
"ON".
comes out from the spout it means that there's an error in the
red, it means that there's an error in the hydraulic circuit. If water
comes out from the spout it means that there's an error in the
flowmeter or in its wiring to the CPU/POWER (JP5); if, on the other
ERROR:
comes out from the spout it means that there's an error in the
flowmeter or in its wiring to the CPU/POWER (JP5); if, on the other
ERROR:
hand, no water comes out it's necessary to check the pump or the
If the number of impulses remains 0 and the display backlight turns
flowmeter or in its wiring to the CPU/POWER (JP5); if, on the other
If the number of impulses remains 0 and the display backlight turns
hand, no water comes out it's necessary to check the pump or the
hydraulic circuit, or the pump wiring (JP24).
red, it means that there's an error in the hydraulic circuit. If water
hand, no water comes out it's necessary to check the pump or the
red, it means that there's an error in the hydraulic circuit. If water
hydraulic circuit, or the pump wiring (JP24).
comes out from the spout it means that there's an error in the
hydraulic circuit, or the pump wiring (JP24).
comes out from the spout it means that there's an error in the
flowmeter or in its wiring to the CPU/POWER (JP5); if, on the other
flowmeter or in its wiring to the CPU/POWER (JP5); if, on the other
hand, no water comes out it's necessary to check the pump or the
hand, no water comes out it's necessary to check the pump or the
hydraulic circuit, or the pump wiring (JP24).
The water now flows out from the spout, causing the update of the
hydraulic circuit, or the pump wiring (JP24).
IMP value with the number of flowmeter impulses. The L/H value
must stay within 10l/h and 18 l/h.
The CA shows the Heater/Grinder page (Heater-Grinder)
The CA shows the Heater/Grinder page (Heater-Grinder)
The CA shows the Heater/Grinder page (Heater-Grinder)
The CA shows the Heater/Grinder page (Heater-Grinder)
The CA shows the Heater/Grinder page (Heater-Grinder)
ERROR:
If the number of impulses remains 0 and the display backlight turns
red, it means that there's an error in the hydraulic circuit. If water
comes out from the spout it means that there's an error in the
flowmeter or in its wiring to the CPU/POWER (JP5); if, on the other
hand, no water comes out it's necessary to check the pump or the
1.6 Page5 (Heater-Grinder)
1.6 Page5 (Heater-Grinder)
hydraulic circuit, or the pump wiring (JP24).
1.6 Page5 (Heater-Grinder)
1.6 Page5 (Heater-Grinder)
1.6 Page5 (Heater-Grinder)
Initial condition
5.0
G Divella
Initial condition
5.0
G Divella
Initial condition
The CA shows the Heater/Grinder page (Heater-Grinder)
revNum
Author
5.0
G Divella
revNum
Author
revNum
Author
5.0
G Divella
5.0
G Divella
revNum
Author
revNum
Author
Press the HOT WATER button to activate the Grinder
1.6 Page5 (Heater-Grinder)
The coffee grinder starts milling for 5000 ms, if the user doesn't
The coffee grinder starts milling for 5000 ms, if the user doesn't
The coffee grinder starts milling for 5000 ms, if the user doesn't
release the button before. In this case the activation time is shown in
release the button before. In this case the activation time is shown in
release the button before. In this case the activation time is shown in
the red-circled field of the picture
the red-circled field of the picture
the red-circled field of the picture
5.0
G Divella
revNum
Author
ERROR:
ERROR:
ERROR:
If this number keeps fixed at 0, the display turns red and the engine
If this number keeps fixed at 0, the display turns red and the engine
If this number keeps fixed at 0, the display turns red and the engine
moves, then there must be a fault in the grinder wiring (JP8), or in
moves, then there must be a fault in the grinder wiring (JP8), or in
moves, then there must be a fault in the grinder wiring (JP8), or in
the grinder itself.
the grinder itself.
the grinder itself.
Keep pressed STANDBY for 5 secs to reset grinder parameters
Keep pressed STANDBY for 5 secs to reset grinder parameters
Pressing button STANDBY for 5 secs resets grinder parameters
Keep pressed STANDBY for 5 secs to reset grinder parameters
Pressing button STANDBY for 5 secs resets grinder parameters
Pressing button STANDBY for 5 secs resets grinder parameters
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Press the HOT WATER button to activate the Pump
Press the HOT WATER button to activate the Pump
Press the HOT WATER button to activate the Pump
Press the HOT WATER button to activate the Pump
Press the HOT WATER button to activate the Pump
Press the HOT WATER button to activate the Pump
Press the STEAM WATER button
Press the STEAM WATER button
Press the STEAM WATER button
Press the STEAM WATER button
Press the STEAM WATER button
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Press the STEAM WATER button
Verified
Approved
Verified
Approved
Verified
Approved
Verified
Verified
Approved
Press the HOT WATER button to activate the Grinder
Press the HOT WATER button to activate the Grinder
Verified
Filename
Filename
Filename
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
05 SERVICE MODE
Intelia_EVO2_AMF_TestMode_V05
Filename
Intelia_EVO2_AMF_TestMode_V05
Filename
Intelia_EVO2_AMF_TestMode_V05
Filename
Intelia_EVO2_AMF_TestMode_V05
Filename
Intelia_EVO2_AMF_TestMode_V05
Filename
Filename
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
12/06/2015
12/06/2015
SaveDate
12/06/2015
SaveDate
SaveDate
12/06/2015
12/06/2015
Approved
SaveDate
SaveDate
12/06/2015
Approved
SaveDate
9/12
9/12
P/PP
9/12
P/PP
P/PP
9/12
9/12
P/PP
P/PP
9/12
P/PP
5/8
- Quick Links:
- Disassembly
Hide quick links:
Advertisement
Table of Contents
