Saeco GAGGIA VELASCA CMF-OTC Service Manual page 35

GAGGIA VELASCA
1.4 Page 3 (BU)
Initial condition
Press the ESPRESSO button to conduct the BU to the Work position
When the BU reaches the work position the value WORK turns from "N"
to "Y". The absorbed BU current must be less than 200mA if the BU is not
inserted, and less than 300mA if the BU is inserted
ERRORS occur if:
The WORK value stays fixed on "N" while the backlight turns RED from
WHITE; in this case check the microswitch, the BU engine (could be
blocked) and, finally, the JP16 and JP14 wirings.
ERROR (BU not inserted):
If the absorbed current is more than 200 mA the display backlight turns
red. In this case check the gears of the engine and its standing in the
housing.
ERROR (BU inserted):
If the absorbed current is more than 300 mA the display backlight turns
red. In this case check the gears of the engine and its standing in the
housing.
Press the COFFEE button to move the BU towards the HOME position
When the BU reaches the HOME position the HOME value changes from
"N" to "Y". The maximum absorbed current must be less than 200 mA (BU
not inserted) / 300 mA (BU inserted)
ERRORS occur if:
The HOME value stays fixed on "N" while the backlight turns RED from
WHITE; in this case check the microswitch, the BU engine (could be
blocked) and, finally, the JP16 and JP14 wirings.
ERROR (BU not inserted):
If the absorbed current is more than 200 mA the display backlight turns
red. In this case check the gears of the engine and its standing in the
housing.
ERROR (BU inserted):
If the absorbed current is more than 300 mA the display backlight turns
red. In this case check the gears of the engine and its standing in the
housing
Press the STEAM button (Press CAPPUCCINO for OTC version)
The CA goes to the EV/PUMP page (EV - PUMP)
1.4 Page 3 (BU)
1.4 Page 3 (BU)
1.4 Page 3 (BU)
Initial condition
1.4 Page 3 (BU)
Initial condition
Initial condition
1.4 Page 3 (BU)
Initial condition
Initial condition
Press the ESPRESSO button to conduct the BU to the Work position
Press the ESPRESSO button to conduct the BU to the Work position
When the BU reaches the work position the value WORK turns from
Press the ESPRESSO button to conduct the BU to the Work position
When the BU reaches the work position the value WORK turns from
"N" to "Y". The absorbed BU current must be less than 200mA if the
Press the ESPRESSO button to conduct the BU to the Work position
When the BU reaches the work position the value WORK turns from
"N" to "Y". The absorbed BU current must be less than 200mA if the
BU is not inserted, and less than 300mA if the BU is inserted
When the BU reaches the work position the value WORK turns from
"N" to "Y". The absorbed BU current must be less than 200mA if the
BU is not inserted, and less than 300mA if the BU is inserted
"N" to "Y". The absorbed BU current must be less than 200mA if the
BU is not inserted, and less than 300mA if the BU is inserted Press the ESPRESSO button to conduct the BU to the Work position
BU is not inserted, and less than 300mA if the BU is inserted
When the BU reaches the work position the value WORK turns from
"N" to "Y". The absorbed BU current must be less than 200mA if the
BU is not inserted, and less than 300mA if the BU is inserted
ERRORS occur if:
ERRORS occur if:
The WORK value stays fixed on "N" while the backlight turns RED
ERRORS occur if:
The WORK value stays fixed on "N" while the backlight turns RED
from WHITE; in this case check the microswitch, the BU engine
ERRORS occur if:
The WORK value stays fixed on "N" while the backlight turns RED
from WHITE; in this case check the microswitch, the BU engine
(could be blocked) and, finally, the JP16 and JP14 wirings.
The WORK value stays fixed on "N" while the backlight turns RED
from WHITE; in this case check the microswitch, the BU engine
(could be blocked) and, finally, the JP16 and JP14 wirings.
from WHITE; in this case check the microswitch, the BU engine
(could be blocked) and, finally, the JP16 and JP14 wirings.
ERRORS occur if:
(could be blocked) and, finally, the JP16 and JP14 wirings.
The WORK value stays fixed on "N" while the backlight turns RED
from WHITE; in this case check the microswitch, the BU engine
(could be blocked) and, finally, the JP16 and JP14 wirings.
ERROR (BU not inserted):
ERROR (BU not inserted):
If the absorbed current is more than 200 mA the display backlight
ERROR (BU not inserted):
If the absorbed current is more than 200 mA the display backlight
turns red. In this case check the gears of the engine and its standing
ERROR (BU not inserted):
If the absorbed current is more than 200 mA the display backlight
turns red. In this case check the gears of the engine and its standing
in the housing.
If the absorbed current is more than 200 mA the display backlight
turns red. In this case check the gears of the engine and its standing
in the housing.
turns red. In this case check the gears of the engine and its standing
in the housing.
ERROR (BU not inserted):
in the housing.
If the absorbed current is more than 200 mA the display backlight
turns red. In this case check the gears of the engine and its standing
in the housing.
ERROR (BU inserted):
ERROR (BU inserted):
If the absorbed current is more than 300 mA the display backlight
ERROR (BU inserted):
If the absorbed current is more than 300 mA the display backlight
turns red. In this case check the gears of the engine and its standing
ERROR (BU inserted):
If the absorbed current is more than 300 mA the display backlight
turns red. In this case check the gears of the engine and its standing
in the housing.
If the absorbed current is more than 300 mA the display backlight
turns red. In this case check the gears of the engine and its standing
in the housing.
turns red. In this case check the gears of the engine and its standing
in the housing.
ERROR (BU inserted):
in the housing.
If the absorbed current is more than 300 mA the display backlight
turns red. In this case check the gears of the engine and its standing
in the housing.
Press the COFFEE button to move the BU towards the HOME position
Press the COFFEE button to move the BU towards the HOME position
Press the COFFEE button to move the BU towards the HOME position
Press the COFFEE button to move the BU towards the HOME position
Press the COFFEE button to move the BU towards the HOME position
When the BU reaches the HOME position the HOME value changes
When the BU reaches the HOME position the HOME value changes
When the BU reaches the HOME position the HOME value changes
When the BU reaches the HOME position the HOME value changes
from "N" to "Y". The maximum absorbed current must be less than When the BU reaches the HOME position the HOME value changes
from "N" to "Y". The maximum absorbed current must be less than
from "N" to "Y". The maximum absorbed current must be less than
from "N" to "Y". The maximum absorbed current must be less than
200 mA (BU not inserted) / 300 mA (BU inserted) from "N" to "Y". The maximum absorbed current must be less than
200 mA (BU not inserted) / 300 mA (BU inserted)
200 mA (BU not inserted) / 300 mA (BU inserted)
200 mA (BU not inserted) / 300 mA (BU inserted)
200 mA (BU not inserted) / 300 mA (BU inserted)
5.0 G Divella
5.0 G Divella
revNum Author
5.0 G Divella
revNum Author
ERRORS occur if:
ERRORS occur if:
ERRORS occur if:
ERRORS occur if: 5.0 G Divella
revNum Author
ERRORS occur if: The HOME value stays fixed on "N" while the backlight turns RED
The HOME value stays fixed on "N" while the backlight turns RED
The HOME value stays fixed on "N" while the backlight turns RED
The HOME value stays fixed on "N" while the backlight turns RED
revNum Author
The HOME value stays fixed on "N" while the backlight turns RED from WHITE; in this case check the microswitch, the BU engine
from WHITE; in this case check the microswitch, the BU engine
from WHITE; in this case check the microswitch, the BU engine
from WHITE; in this case check the microswitch, the BU engine
5.0 G Divella
from WHITE; in this case check the microswitch, the BU engine (could be blocked) and, finally, the JP16 and JP14 wirings.
(could be blocked) and, finally, the JP16 and JP14 wirings.
(could be blocked) and, finally, the JP16 and JP14 wirings.
(could be blocked) and, finally, the JP16 and JP14 wirings.
revNum Author
(could be blocked) and, finally, the JP16 and JP14 wirings.
ERROR (BU not inserted):
ERROR (BU not inserted):
ERROR (BU not inserted):
ERROR (BU not inserted):
ERROR (BU not inserted):
If the absorbed current is more than 200 mA the display backlight
If the absorbed current is more than 200 mA the display backlight
If the absorbed current is more than 200 mA the display backlight
If the absorbed current is more than 200 mA the display backlight
If the absorbed current is more than 200 mA the display backlight turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing in the housing.
in the housing.
in the housing.
in the housing.
in the housing.
ERROR (BU inserted):
ERROR (BU inserted):
ERROR (BU inserted):
ERROR (BU inserted):
ERROR (BU inserted):
If the absorbed current is more than 300 mA the display backlight
If the absorbed current is more than 300 mA the display backlight
If the absorbed current is more than 300 mA the display backlight
If the absorbed current is more than 300 mA the display backlight
If the absorbed current is more than 300 mA the display backlight
turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing
turns red. In this case check the gears of the engine and its standing
in the housing.
in the housing.
in the housing.
in the housing.
in the housing.
The CA goes to the EV/PUMP page (EV - PUMP)
The CA goes to the EV/PUMP page (EV - PUMP)
The CA goes to the EV/PUMP page (EV - PUMP)
The CA goes to the EV/PUMP page (EV - PUMP)
The CA goes to the EV/PUMP page (EV - PUMP)
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Test Mode INTELIA EVO V2 AMF
Verified Approved
Verified Approved
Verified Approved
Verified Approved
Verified Approved
Press the STEAM button
Press the STEAM button
Press the STEAM button
Press the STEAM button
Press the STEAM button
Filename
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
Filename
Intelia_EVO2_AMF_TestMode_V05
05 SERVICE MODE
Filename
Filename
Filename
Filename
Filename
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
Intelia_EVO2_AMF_TestMode_V05
12/06/2015 7/12
12/06/2015 7/12
SaveDate P/PP
12/06/2015 7/12
SaveDate P/PP
12/06/2015 7/12
SaveDate P/PP
SaveDate P/PP
12/06/2015 7/12
SaveDate P/PP
4/8