Copy Of The Lighting Plate Instructions - Regency Gas Fireplace P42-LP4 Owners & Installation Manual

COPY OF THE LIGHTING PLATE INSTRUCTIONS

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/
NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. (Australia: AS5601-2004, New Zealand: NZS 5261)
WARNING: If you do not follow these instructions exactly, a fi re or explosion may result causing property damage,
personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to the owner's information manual provided with this appliance. For assistance
or additional information consult a qualifi ed installer, service agency or gas supplier.
A) This appliance has a pilot which must be lighted by hand, following the instructions below exactly.
B) BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the fl oor because some gas is heavier than
air and will settle on the fl oor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance
- Do not touch any electric switch, do not use any phone in your building
- Immediately call your gas supplier from a neighbors phone. Follow the gas supplier's instructions.
- If you cannot reach your gas supplier, call the fi re department.
C) Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to
repair it, call a qualifi ed service technician. Force or attempted repair may result in a fi re or explosion.
D) Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to inspect the appliance and
to replace any part of the control system and any gas control which has been under water.
E) This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface temperatures
keep children, clothing and furniture, gasoline and other liquids having fammable vapors away. Keep burner
and control compartment clean. See installation and operating instructions accompanying appliance.
FOR UNITS NOT EQUIPPED WITH ELECTRIC SPARK:
1) Push in gas control knob slightly and turn clockwise
"OFF". Knob cannot be turned from "PILOT" to "OFF" unless
knob is pushed in slightly. Do not force.
PILOT BURNER
VEILLEUSE
THERMOPILE
ELEMENT
THERMO-
ELECTRIQUE
2) Wait fi ve (5) minutes to clear out any gas. If you then smell gas
STOP! follow "B" in the safety information above on this label. If
you don't smell gas, go to the next step.
3) Turn knob on gas control counterclockwise
4) Push in control knob all the way and hold in. Immediately push
black button on spark igniter until pilot lights. Continue to hold the
control knob in for about 1/2 minute after the pilot is lit. Release
knob and it will pop back up. Pilot should remain lit. If it goes out,
repeat steps 3) and 4).
If knob does not pop up when released, stop and immediately call
your service technician or gas supplier.
If the pilot will not stay lit after several tries, turn the gas control
knob to "OFF" and call your service technician or gas supplier.
5) Turn gas control knob counterclockwise
6) Use rocker switch to operate main burner.
1) Tur n off the fl a me swi tc h.
2) P u sh i n the g as con trol k no b sl i g ht l y a nd t u rn cl oc kw i se
3) Tur n off al l el e ctr i c p ower to th e ap pl i a nc e i f s er vi ce is t o b e p er f o rm e d.
Regency ® P42-4 Zero Clearance Direct Vent Gas Fireplace
FOR YOUR SAFETY READ BEFORE LIGHTING
LIGHTING INSTRUCTIONS
STOP! Read the safety information above on this label.
Gas Inlet
to "PILOT".
to "ON".
TO TURN OFF GAS APPLIANCE
You m ay sh ut off th e pi l ot dur i ng p rol o ng e d n o n u se p er io d s t o c on se r ve f u e l.
DO NOT REMOVE THIS INSTRUCTION PLATE
OPERATING INSTRUCTIONS
FOR ALL PROPANE UNITS AND
UNITS EQUIPPED WITH ELECTRIC SPARK BOXES:
to
1) Push in gas control knob slightly and turn to "PILOT" position.
OFF
2) Push in control knob all the way and hold in until the pilot lights
up. Continue to hold the control knob in for about 20 seconds
after the pilot is lit. Release knob.
3) Push in gas control knob slightly and turn to "ON" position.
4) Turn ON the fl ame switch.
Gas Inlet
t o " OF F" . D o no t f or ce .
918-474a
35