Regency P121-NG1 Owners & Installation Manual

Regency P121-NG1 Owners & Installation Manual

P121 / p121lc / p121rc / p131 zero clearance direct vent gas fireplace

Advertisement

P121 / P121LC / P121RC / P131
Zero Clearance Direct Vent Gas Fireplace
WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage, per-
sonal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapours and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualifi ed in-
staller, service agency or the gas supplier.
Tested by:
918-107b
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
www.regency-fi re.com
STYLE
See Thru
P121-NG1 Natural Gas
Left Corner
P121LC-NG1 Natural Gas P121LC-LP1 Propane
Right Corner P121RC-NG1 Natural Gas
P121RC-LP1 Propane
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
MODEL
P121-LP1 Propane
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch: do not use any
phone in your building.
Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fi re
department.
Owners &
Installation Manual
01/09/06

Advertisement

Table of Contents
loading

Summary of Contents for Regency P121-NG1

  • Page 1 P121 / P121LC / P121RC / P131 Owners & Zero Clearance Direct Vent Gas Fireplace Installation Manual STYLE MODEL See Thru P121-NG1 Natural Gas P121-LP1 Propane Left Corner P121LC-NG1 Natural Gas P121LC-LP1 Propane Right Corner P121RC-NG1 Natural Gas...
  • Page 2: Manufactured Mobile Home Requirements

    INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE This Regency product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: VENTED GAS FIREPLACE HEATERS ANSI Z21.88a-2000/CSA 2.33a-2000 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN/CGA 2.17-M91.
  • Page 3: Table Of Contents

    Glass Door Removal ..........27 Finishing Trim ............27 Louvers and Grills ............ 27 Remote Control (optional) ........28 Remote Wall Switch (optional) ......... 28 Wall Thermostat (optional) ........28 Wiring Diagram ............29 Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 4: Safety Label

    For the State of Massachusetts, fl exible connectors shall not exceed 36 inches in length. For the State of Massachusetts, the appli- ances individual manual shut-off must be a t-handle type valve. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 5: Important Message

    AND SHOULD STAY AWAY TO AVOID manufacturer. 14) The appliance area must be kept clear and BURNS OR CLOTHING IGNITION. free of combustible materials, (gases and other fl ammable vapours and liquids). Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 6: Specifi Cations

    INSTALLATION SPECIFICATIONS P121-1 See Thru Note: These units are non-load bearing. P131-1 Pier Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 7 INSTALLATION P121LC-1 Left Corner Unit Note: These units are non-load bearing. P121RC-1 Right Corner Unit Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 8: Locating Your Gas Fireplace

    Have a qualifi ed inspector, dealer, or installer review C) P121LC-1 Left Corner your plans before installation. Note: For Exterior Vent Termination Locations see page 12. D) P121RC-1 Right Corner Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 9: Clearances

    Caution: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour. * If the 3" (76mm) metal extension trim is removed it must be replaced with a 8" (203mm) non-combustible material. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 10: Framing And Finishing

    fl ex, see Vent Clearances, page 9. P121LC-1 - Corner Unit P121-1 - See Thru P131-1 - Pier P121RC-1 - Corner Unit Note: These units are non-load bearing. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 11: Facing And Finishing Requirements

    Each direct vent gas appliance must use it's own separate vent system. Common vent systems 3) Attach the standoff securely to the top are prohibited. with 4 screws per standoff (on opposite corners). Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 12: Exterior Vent Termination Locations

    INSTALLATION EXTERIOR VENT TERMINATION LOCATIONS Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 13: Rigid Pipe Venting Components List

    Vent Guard (Optional) - Riser Vent Terminal 510-994 Rigid Pipe Adaptor (must be used with all rigid 946-523/P AstroCap Horizontal Cap pipes) 946-206 Vinyl Siding Standoff - AstroCap 640-530/P Riser Vent Terminal Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 14: Venting: Direct Vent System (Flex)

    12. Regency Direct Vent (Flex) System Termination Kit (Part# 946-513) includes all the parts needed to install the P121-1/P121LC-1/P121RC- 1/P131-1 with a maximum run of 2 feet. If installing the P121-1/P121LC-1/P121RC-1/P131-1 with a continous vent length of more than 2 ft.
  • Page 15: Rigid Pipe Venting Systems

    American Metal Products, Ameri Vent Direct vent and Selkirk Direct-Temp. FPI , and FPI AstroCap are the proprietary trademarks of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 16: Venting Arrangements Horizontal Terminations

    INSTALLATION RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS REGENCY DIRECT VENT SYSTEM (FLEX) (Propane & Natural Gas) The diagram below shows examples of horizontal termination arrangements using one, two, or three 90 elbows (two 45 elbows equal one 90 elbow).
  • Page 17 With the above options, maximum total pipe length if 37 feet with mini- mum of 5 feet total vertical and maximum 12 feet total horizontal. Please note minimum 1 foot between 90 elbows is required. Diagram 4 Diagram 6 Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 18: Vertical Terminations

    Rigid Pipe Adaptor will pertrude past the unit 1-1/2" (38mm) when measured from the rear standoffs. Note: A 1-1/4" (32mm) clearance from the elbow must also be main- tained. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 19 With the above options, maximum total pipe length if 37 feet with mini- mum of 5 feet total vertical and maximum 12 feet total horizontal. Please note minimum 1 foot between 90 elbows is required. Diagram 11 Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 20: Venting - Dura-Vent Horizontal Installations

    1/4 inch rise for every 1 foot recessed into the siding. ends, Diagram 1. Push the pipe sections completely together, then twist-lock Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 21: Venting - Dura-Vent Vertical Termination

    11/12 to 12/12 1.22 over 12/12 to 14/12 1.52 over 14/12 to 16/12 1.83 over 16/12 to 18/12 2.13 over 18/12 to 20/12 2.29 over 20/12 to 21/12 2.44 Diagram 5 Diagram 3 Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 22: System (Flex)

    Note: If installing termination on a siding covered wall, furring strips must be used to ensure that the termination is not recessed into the siding. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 23: Converion To Propane

    NG to LPG using SIT conversion Kit Code 0.907.202" onto the 17) Check for proper fl ame appearance and valve. glow on logs. 13) Replace yellow "Natural Gas" label with red "Propane" label Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 24: System Data

    CAN/CGA B149 installation code. test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 25: Log Set Installation

    3) Place Log 327 on the front left side of the burner. Position the right end of the log in between the two tabs and the left end of the log into the grate post. Tab on Burner Grate Post Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 26 Log onto the second grate post from the left. Ensure that the log fi ts into a pin that is on Log 326. Place Log 329 onto pin. Grate Post Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 27: Glass Door Removal

    3) P131 & P121LC/P121RC Corner Model: Remove the 6 screws that secure the glass Push trim tight door and repeat step 2. The Top and Bottom Side Louver or Grill is against magnet. installed the same way. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 28: Remote Control (Optional)

    4 AA alkaline batteries in the receiver. Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote control is now ready for operation. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 29: Wiring Diagram

    (Millivolt) (Optional) CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Terminal Block Location Terminal Block Remove cover to ac- cess Terminal Block Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 30: Operating Instructions

    WHILE IT IS HOT. sound when ON. 3) Turn gas control knob counterclockwise so indicator points to the "PILOT" position. Depress the gas control knob fully. Depress the igniter button several times until the Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 31: Lighting Plate Instructions

    Unit Body/Firebox: Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 32: Maintenance Instructions

    fi ttings. It may once a year. When cleaning the logs, use a Your Regency fi replace is supplied with high be caused by having excessive lateral runs, soft clean paint brush as the logs are fragile temperature 5mm-Tempered glass &...
  • Page 33: Removing Valve

    11) Remove the 16 Phillips head screws securing the valve tray. 6) Remove the burner by removing the 4 screws. 12) Lift the entire assembly out. 7) Slide the burner assembly away from the orifi ce and lift out. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 34: Installing Valve

    15) Check the manifold pressure. 16) Reinstall the logs, grate and brick panels as needed. 17) Reinstall the glass doors. 18) Fire up the unit again and check for proper fl ame appearance. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 35: Parts List

    Brick Panel - Base - Side 34) 902-298 Brick Panel - Side 98) 910-366 Switch Cover Plate 99) 910-363 Wall Switch 100) 910-367 Switch Receptacle Plastic 910-882 Wire - Valve to Burner Switch Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 36 Louver Side - Black/Brass (set) 34) 902-298 Brick Panel - Side 98) 910-366 Switch Cover Plate 99) 910-363 Wall Switch 100) 910-367 Switch Receptacle Plastic 910-882 Wire - Valve to Burner Switch Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 37 Brick Panel - Base - Front 360-924 Louver Front - Black/Steel (set) 34) 902-298 Brick Panel - Side 360-926 Louver Front - *Not available as a replacement part. 35) 902-300 Brick Panel - Front Black/Brass (set) Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 38 Louver Front - Black (set) 360-922 Louver Front - Black/Gold (set) 34) 902-298 Brick Panel - Side 35) 902-300 Brick Panel - Front 360-924 Louver Front - Black/Steel (set) 360-926 Louver Front - Black/Brass (set) Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 39 Pilot Assembly Gasket 69) 910-190 Piezo Ignitor and Nut 79) 360-525 Burner Assembly 82) 360-027 Grate Assembly 904-690 Orifi ce #31 - NG 936-170 Orifi ce Gasket *Not available as a replacement part. Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 40 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 41 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 42 NOTES ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace...
  • Page 43: Warranty

    WARRANTY Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a Excalibur Product.
  • Page 44 Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency and Panorama are trademarks of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2005, FPI Fireplace Products International Ltd. All rights reserved.

Table of Contents