Regency P40-LP1 Specification Sheet

Direct vent gas fireplace

Advertisement

Quick Links

Model
P40-NG1
Fuel Type
Natural Gas
Minimum Supply Pressure
5" W.C. (1.25 kPa)
Manifold Pressure - High
3.5" W.C. (0.87 kPa)
Manifold Pressure - Low
1.6" W.C. (0.39 kPa)
Orifi ce Size - Front Burner
#44 DMS
Orifi ce Size - Rear Burner
#35 DMS
Minimum Input
13,000 BTU/h (3.81 kW)
Maximum Input
45,000 BTU/h (13.19 kW)
Vent Sizing
5" Inner / 8" Outer
Approved Venting Systems
Flex Vent Systems:
Rigid Pipe Vent Systems:
A
Unit Dimensions
Description
A
Front Face Width
B
Rear Firebox Width
C
Front Face Height
D
Height w/ Standoff
E
Unit Depth
F
Height to Vent
Framing Dimensions Description
G
Framing Width
***
***
H
Framing Height
I
Framing Depth
J
Corner Wall Length
K
Corner Facing Wall Width
L
Minimum Height to Combustibles
M
Vent Centerline Height
N
Non-Combustible Facing Height
O
Gas Connection Height
P
Gas Connection Inset
Q
Gas Connection Width
Important: Framing height requires consideration of the hearth
***
depth. Dimension H = H + the thickness of installed hearth.
June 2007 Regency Product Specifi cations Book
Gas Fireplaces
P40 Direct Vent Gas Fireplace
P40-LP1
Propane
12" W.C. (3.00 kPa)
10" W.C. (2.49 kPa)
3.6" W.C. (0.89 kPa)
#55 DMS
#53 DMS
12,000 BTU/h (3.51 kW)
43,000 BTU/h (12.60 kW)
5" Inner / 8" Outer
FPI AstroCap™ Flex Vent
Simpson Dura-Vent® Direct Vent GS
Selkirk Direct-Temp
B
A
D
C
F
E
P40
40" (1016mm)
33-7/16" (889mm)
34" (864mm)
42-1/2" (1080mm)
20-1/16" (508mm)
35-1/4" (826mm)
P40
40-1/2" (1029mm)
***
42-1/2" (1080mm)
+ Hearth
20-1/16" (508mm)
50-5/8" (1286mm)
71-5/8" (1524mm)
51-7/8" (1318mm)
45-3/8" (1153mm)
10-1/4" (260mm)
1-1/2" (38mm)
4-3/4" (121mm)
3-1/4" (102mm)
Top Header
(non-combustible)
H
G
J
K
Please refer to Page 11 (Exterior Vent Terminations)
for additional guidelines on vent locations.
P40 Gas Fireplace
Unit requires
120V to operate. See
"Wiring Diagram," on page 17,
for more details. Receptacle is
included with manual.
L
Drywall
(or other
Top Header
facing)
(non-combustible)
N
Non-Combustible Facing
11" (279mm)
dia. Hole through
wall Vent.
I
M
O
P Q
Opening for gas
connection
45

Advertisement

Table of Contents
loading

Summary of Contents for Regency P40-LP1

  • Page 1 Gas Connection Inset Gas Connection Width Important: Framing height requires consideration of the hearth depth. Dimension H = H + the thickness of installed hearth. June 2007 Regency Product Specifi cations Book P40-LP1 Propane 12” W.C. (3.00 kPa) 10” W.C. (2.49 kPa) 3.6”...
  • Page 2: Framing And Finishing

    Floor Mounted Fireplace Raised Fireplace Full Screen Door Facing Requirements 10-1/4” Above Fireplace 6” 6” (Hearth must June 2007 Regency Product Specifi cations Book Clearance Dimension 2-1/2” (64mm) 1-1/2” (38mm) 1-1/2” (38mm) 1-1/4” (32mm) WARNING: When installing the Full Screen Doors...
  • Page 3: Combustible Mantels

    #946-618 6 Feet #946-616 10 Feet Notes: Liner sections should be continuous without any joints or seams. Only Flex pipe purchased from Regency may be used for Flex installations. Header Horizontal sections must be supported every 3 feet. Non-Combustible Facing Standoff 5”...
  • Page 4: Rigid Pipe Venting

    Alternate Snorkel Termination Cap Part #1282 (14”) Part #1281 (36”) Minimum 12” (305mm) Vent Restrictor on Set 2 Vent Restrictor on Set 1 Vent Restrictor Factory Set Max. 10’ (3m)(centerline to centerline) June 2007 Regency Product Specifi cations Book 12 12...
  • Page 5: Vertical Venting With Two (2) 90° Elbows

    3x then the vent restrictor 5’ Min. 6’ Max. 8’ Min. must be set to 1. 6’ Min. 7’ Max. 9’ Min. 7’ Min. 8’ Max. 10’ Min. June 2007 Regency Product Specifi cations Book P40 Gas Fireplace...
  • Page 6: Venting Arrangements - Horizontal Terminations

    Vent Restrictor on Set 2 Vent Restrictor on Set 1 45-3/8” (1143mm) Minimum Please refer to Page 11 (Exterior Vent Terminations) Height Requirement for additional guidelines on vent locations. Vent Restrictor Factory Set June 2007 Regency Product Specifi cations Book...
  • Page 7: Horizontal Venting With Two (2) 90° Elbows

    11’ Min. 8’ Max. 7’ Min. 6’ Max. 12’ Min. 9’ Max. June 2007 Regency Product Specifi cations Book Maximum total pipe: length, of all sections, must not exceed 30 feet. Total horizontal sections must not exceed 9 feet. Minimum of 1’ pipe section between any elbows.

This manual is also suitable for:

P40-ng1P40

Table of Contents