Table of Contents
Advertisement
FortiGate-7060E Chassis
Power is provided to the chassis using four hot swappable 3+1 redundant 100-240 VAC, 50-60 Hz AC or -48V DC
power supply units (PSUs). At least three PSUs (power supplies 1 to 3) must be connected to power. Power
supply 4 is a backup power supply. You can add a 5th or 6th power supply for 3+2 and 3+3 redundancy.
The standard configuration of the FortiGate-7060E includes two FIM (interface) modules in chassis slots 1 and 2
and up to four FPM (processing) modules in chassis slots 3 to 6.
FIM modules
FIM modules are hot swappable interface modules that provide data and management interfaces, base
backplane switching and fabric backplane session-aware load balancing for the chassis. The FIM modules
include an integrated switch fabric and DP2 processors to load balance millions of data sessions over the chassis
fabric backplane to FPM processor modules. The following FIM modules are available:
The FIM-7901E includes thirty-two front panel 10GigE SFP+ fabric channel interfaces (A1 to A32). These interfaces
l
are connected to 10Gbps networks. These interfaces can also be configured to operate as Gigabit Ethernet
interfaces using SFP transceivers.
The FIM-7904E includes eight front panel 40GigE QSFP+ fabric channel interfaces (B1 to B8). These interfaces are
l
connected to 40Gbps networks. Using 40GBASE-SR4 multimode QSFP+ transceivers, each QSFP+ interface can
also be split into four 10GBASE-SR interfaces and connected to 10Gbps networks.
The FIM-7910E (shown in
l
interfaces (C1 to C4). These interfaces can be connected to 100Gbps networks. Using 100GBASE-SR10 multimode
CFP2 transceivers, each CFP2 interface can also be split into ten 10GBASE-SR interfaces and connected to
10Gbps networks.
The FIM-7920E includes four front panel 100GigE QSFP28 fabric channel interfaces (C1 to C4). These interfaces
l
can be connected to 100Gbps networks. Using a 100GBASE-SR4 QSFP28 or 40GBASE-SR4 QSFP+ transceiver,
each QSFP28 interface can also be split into four 10GBASE-SR interfaces and connected to 10Gbps networks.
FPM-7620E FPM modules
The FPM-7620E modules are hot swappable processor modules that provide FortiOS firewalling and security
services. The FPM modules function as workers, processing sessions load balanced to them by the FIM modules.
FPM modules include multiple NP6 network processors and CP9 content processors to accelerate traffic.
FortiGate-7060E System Guide
Fortinet Technologies Inc.
Do not operate the FortiGate-7060E chassis with open slots on the front or back panel.
For optimum cooling performance and safety, each chassis slot must contain an FIM
or FPM module or an FIM or FPM blank panel (also called a dummy card). For the
same reason, all cooling fan trays, power supplies or power supply slot covers must be
installed while the chassis is operating.
FIM modules on page
If you are installing different FIM modules in the FortiGate-7060E chassis, for optimal
configuration you should install the module with the lower model number in slot 1 and
the module with the higher number in slot 2. For example, if your chassis includes a
FIM-7901E and a FIM-7904E, install the FIM-7901E in chassis slot 1 and the FIM-
7904E in chassis slot 2. Also, for example, if your chassis includes a FIM-7904E and a
FIM-7920E, install the FIM-7904E in chassis slot 1 and the FIM-7920E in chassis slot
2. This applies to any combination of two different interface modules.
6) includes four front panel 100GigE CFP2 fabric channel
FortiGate-7060E front panel
6
Advertisement
Table of Contents
