Wacom DTU-710 Safety Instructions
  1. Manuals
  2. Brands
  3. Wacom Manuals
  4. Monitor
  5. DTU-710
  6. Safety instructions
Wacom DTU-710 Safety Instructions

Wacom DTU-710 Safety Instructions

Interactive pen display
Hide thumbs Also See for DTU-710:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual and Installation Instructions, User Manual
DTU-710
INTERACTIVE PEN DISPLAY
WARNING
Do not use DTU-710 Interactive Pen Display in a facility control
system that requires extremely high reliability; it may cause other
electronic devices to malfunction, or other devices may cause DTU-710 to
malfunction.
Where use is prohibited, power off DTU-710 to prevent the possibility of it
causing other electronic devices to malfunction. Wacom does not accept
any liability for direct or consequential damages. For details, please refer
to your Warranty, located at the inside back cover of this manual.
HIGH VOLTAGE
Do not open DTU-710. It has the risk of electric shock.
Only use the AC adaptor that came with DTU-710. If a different type
of AC adaptor is used, DTU-710 will not work properly or it may be
damaged. Using a different type of AC adaptor also has the potential
to result in fire. Use of a different AC adaptor will void your warranty.
CAUTION
Prevent your children from swallowing the pen nib or side switch
knob. The pen nib or side switch knob may accidentally be pulled out if
children are biting on them.
If the LCD screen has been damaged, DO NOT touch any liquid
that may be leaking from it; this liquid is an irritant. In case of contact
with skin, eyes, or mouth, rinse immediately with running water for at
least 15 minutes or more. If contact is made with the eyes or mouth,
also consult a physician.
When adjusting the tilt angle of DTU-710, be careful to avoid
catching your finger in the gap of the movable portion of the stand.
Be sure to use a grounded power source when applying power to
DTU-710.
DTU-710_EN.indd 1
SAFETY INSTRUCTIONS
04.7.20 8:31:30 PM

Advertisement

Table of Contents
loading

Related Manuals for Wacom DTU-710

Summary of Contents for Wacom DTU-710

  • Page 1 Do not open DTU-710. It has the risk of electric shock. Only use the AC adaptor that came with DTU-710. If a different type of AC adaptor is used, DTU-710 will not work properly or it may be damaged. Using a different type of AC adaptor also has the potential to result in fire.

  • Page 2: Introduction And Overview

    This manual describes how to install DTU-710 hardware and software. It also describes how to use DTU-710 and the pen. Note that the computer treats the two parts of DTU-710 (the LCD monitor and the Wacom tablet) as separate pieces of hardware. Therefore, the instal- lation process is completed in two stages.

  • Page 3: Precautions On Use And Handling

    Failure to do so could also void your warranty, in which case Wacom shall have no responsibility for such loss or damage and to repair or replace the product.

  • Page 4: Table Of Contents

    Table of Contents Checking Packed Components Installation LCD Monitor Installation Tablet Software Installation for Windows and Macintosh Customizing DTU-710 - The Basics Opening the Wacom Tablet Control Panel Calibrating the Tablet DTU-710 Component Functions Front View Rear View Using an Alternate Mount or Stand...

  • Page 5: Checking Packed Components

    DVI-DVI Cable and DVI-VGA Cable* Some package configurations includ an additional CD containing bundled software applications. Please retain the package box for use when storing or shipping DTU-710. * For DTU-710 only. Do not use with other devices. DTU-710_EN.indd 5...

  • Page 6: Installation

    Installation LCD Monitor Installation First install the monitor portion of DTU-710. Do not connect the USB cable or serial data cable until you procede to the step " ". Turn off your computer. IMPORTANT: Never connect or disconnect the DVI video cable or power cable while your computer or DTU-710 is powered on.

  • Page 7: Tablet Software Installation For Windows And Macintosh

    Connect the AC adaptor power cable and plug the adaptor into an AC outlet. Turn on the power switch of DTU-710. The power lamp will light blue, and then turns orange. Turn on your computer to start your operating system.

  • Page 8: Customizing Dtu-710 - The Basics

    Customizing DTU-710 – The Basics Opening the Wacom Tablet Control Panel The Wacom Tablet Control Panel makes it easy to customize your Interactive Pen Display and the pen. To open the control panel: Windows: Click on the Windows Start button and choose Programs. From the Wacom Tablet group, choose the Wacom Tablet option.

  • Page 9: Calibrating The Tablet

    You will need to calibrate the tablet in order to line up the screen cursor position with the position of the pen on DTU-710. This is required to adjust for parallax caused by the display screem overlay. After setting the tablet in its working position, follow the procedure below to calibrate the tablet.

  • Page 10: Dtu-710 Component Functions

    - When a still image is displayed for a long period of time, an afterimage may remain for a short period of time. As the tablet portion of DTU-710 emits electromagnetic waves at a certain frequency, if another tablet is closely placed to DTU-710, the screen cursor may jitters or jumps around. To solve this problem, place the tablet away from DTU-710.

  • Page 11: Rear View

    IMPOTANT Be sure to adjust the tilt angle of the stand to the low tilt position before packaging DTU-710. If you do not close the stand, the notched mechanism may be damaged during transportation and storage. Do not lift the unit by the stand; this may damage the stand mechanism. When lifting or moving the unit, always do so by grasping the main body casing.

  • Page 12: Using An Alternate Mount Or Stand

    DTU-710 Component Functions Using an Alternate Mount or Stand If you will be using DTU-710 in an installation that requires the use of an alternate mounting platform, you can remove the adjustable stand from DTU-710 and mount the pen display onto a VESA conforming mount arm or stand.

  • Page 13: Using The Pen

    Using the Pen Hold the pen as you would a pencil. Make sure the side switch is in a convenient location where you can press it with your thumb or forefinger, but won't accidentally press it while drawing. Eraser Eeasar Second Side Switch Side Switch Tip Switch...

  • Page 14: Using A Pen

    Move the pen above DTU-710 screen to position the screen cursor. The cursor instantly jumps to the new location (absolute positioning). Press the pen tip on DTU-710 screen to make a se- lection. Note: If the screen cursor is not aligned with the pen tip, you will need to calibrate DTU-710. Clicking Double-Clicking...

  • Page 15: Adjusting The Lcd Monitor

    Multi-Sync functions if the horizontal frequency is between 30 to 80 kHz and the vertical frequency is between 50 to 75 Hz. If DTU-710 does not automatically synchronize with the incoming signal, you can use the OSD Reset Auto Adjust option to initiate display synchronization.

  • Page 16: Horizontal Center

    Adjusting the LCD Monitor Horizontal Center Menu Position (VGA only) Select to move the OSD menu around the display. Select to move the screen image left or right. To automatically adjust, use the Reset option. Vertical Center Reset (VGA only) Provides two options: Select to move the Use Auto Adjust to reset...

  • Page 17: Adjusting Pitch And Phase

    Some computers and video cards may not allow the multi-sync function to fully work when DTU-710 is first connected. If some portion of the text appears blurred, adjust the pitch and phase by following the procedure below. For crisp images, set the DTU-710 resolution of your video card to 1280 x 1024.

  • Page 18: Power Saving

    Power Saving DTU-710 conforms to VESA and Energy Star power saving guidelines. When using DTU-710 with a VESA DPMS Display Power Management Signaling (DPMS) compliant computer or graphics card, the display will automatically comply with the below power saving parameters.

  • Page 19: Caring For Your Dtu-710

    Caring for DTU-710 Cleaning T o clean the DTU-710 casing, use a soft cloth with mild detergent (such as dish washing liquid) diluted with water. Do not use paint thinner, benzine, alcohol, or other organic solvents to clean DTU-710 casing or pen.

  • Page 20: Display Troubleshooting

    Display Troubleshooting If you encounter problems with DTU-710 display, refer to the following tables. Your problem may be described here, and you can try the solution offered. For the problems regarding tablet or pen, refer to the Troubleshooting chapter in the online Help that can be accessed from the Wacom Tablet control panel.
  • Page 21 The image appears multiple times switch box. on the display. Be sure the DTU-710 color profile has been installed and is The color white does not display as ■ selected as the profile for use with your operating system and white.

  • Page 22: Obtaining Technical Support

    Obtaining Technical Support If you have a problem with DTU-710, first check the appropriate setup chapter in this guide to make sure the unit is installed correctly. Then review the Troubleshooting section within this manual and the online Help; your problem may be described there and you can try the solution offered.

  • Page 23: Specifications

    Specifications General Specifications Physical dimensions (WxDxH): 418x362x57mm (excluding the stand) Weight: 5.8kg (including the stand) Main Unit input Voltage: DC12V Power consumption: 45W or less (DC12V) Operating temp. & humidity: 5 to 35 deg. C, 80%RH (non condensing) Storage temp. & humidity: 10 to 60deg.

  • Page 24: Power Adaptor

    Specifications Power Adaptor Input voltage: 100 to 240 VAC, 50/60 Hz Output voltage: 18 VDC, 2.5 A Pen (UP-911E) Pen tip travel: 0.1 mm (0.004 in) or less Eraser tip travel: 2 mm (0.08 in), approximately Physical dimensions, weight: 14.0 x 159.0 mm, 16g (0.63 x 6.26 in, 0.56 oz) Side switch type: Rocker switch Pen Accessories...

  • Page 25: Radio And Television Interference

    The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used properly – that is, in strict accordance with Wacom instructions – it may cause interference with radio and television reception.

Table of Contents