Mode Transition And Structure Of Layers In Service Factory Mode - Pioneer PDP-5020FD Service Manual

1
A
Mode transition in Service Factory mode
Up
Down
INFORMATION mode
1. VERSION (1)
2. VERSION (2)
B
3. MAIN NG
4. TEMPERATURE
5. HOUR METER
6. HDMI SIGNAL INFO 1
7. HDMI SIGNAL INFO 2
8. VDEC SIGNAL INFO 1
9. VDEC SIGNAL INFO 2
PANEL FACTORY mode
1. PANEL INFORMATION
2. PANEL WORKS
3. POWER DOWN
C
4. SHUT DOWN
5. PANEL-1 ADJ
6. PANEL-2 ADJ
7. PANEL FUNCTION
8. ETC.
9. RASTER MASK SETUP
10. PATTEN MASK SETUP
11. COMBI MASK SETUP
Structure of Layers in Panel Factory Mode 1
1. PANEL INFORMATION Version indication of the panel
2. PANEL WORKS Indications of the accumulated power-on time and
power-on count of the panel
3. POWER DOWN Indication of the Power-down history
D
4. SHUT DOWN Indication of the Shutdown history
5. PANEL-1 ADJ (+)
1. VOL SUS
2. VOL OFFSET
Settings required after replacement of the panel
• • • • •
10. RESET1ST_KSB
• • • • •
Items for factory use
25. SUS FREQ
For AM noise prevention (Depending on the mode,
brightness of the screen changes.)
For confirmation of the result of the setting change,
the unit must be turned off then back on again.
6. PANEL-2 ADJ (+)
1. R-HIGH
2. G-HIGH
For the WB adjustment of the panel and ABL
• • • • •
adjustment.
E 6. B-LOW
A setting table is available for each signal frequency.
7. ABL
7. PANEL FUNCTION (+)
1. R-LEVEL
Items for factory use
• • • • •
To "Structure of Layers in Panel Factory Mode 2"
F
18
1
2
Quick Reference upon Service Visit 2

Mode transition and structure of layers in Service Factory mode

• To shift to another mode, press [MUTING].
• To shift to another item in a specific mode,
press [i] or [j].
• To shift to the next nested layer below for an
item with a "(+)" indication, press [ENTER/SET].
To return to the next nested layer above,
also press [ENTER/SET].
INITIALIZE mode
1. SIDE MASK LEVEL
2. FINAL SETUP
3. DTB SERVICE MENU
4. Wide XGA AUTO
5. AUTO ADJUSTMENT
OPTION mode
1. CH PRESET
2. ANTENNA MODE
3. AFT
4. SYNC DET
5. CTI
6. CC
2
3
Structure of Layers in Service Factory Mode
INFORMATION mode
1. VERSION (1)
2. VERSION (2)
3. MAIN NG
3-1. CLEAR
4. TEMPERATURE
5. HOUR METER
5-1. CLEAR
6. HDMI SIGNAL INFO 1
7. HDMI SIGNAL INFO 2
8. VDEC SIGNAL INFO 1
9. VDEC SIGNAL INFO 2
PANEL FACTORY mode
OPTION mode
1. CH PRESET
2. ANTENNA MODE
3. AFT
4. SYNC DET
5. CTI
6. CC
INITIALIZE mode
1. SIDE MASK LEVEL
1-1. SIDE MASK LEVEL
2. FINAL SETUP
2-1. DATA RESET
3. DTB SERVICE MODE
3-1. MODE SHIFT
4. Wide XGA AUTO
5. AUTO ADJUSTMENT
Structure of Layers in Panel Factory Mode 2
8. ETC (+)
1. BACKUP DATA
2. DIGITAL EEPROM
3. PD INFO.
4. SD INFO.
5. HR-MTR INFO.
6. PM/B1-B5
7. P COUNT INFO.
8. MAX TEMP.
9. MIRROR
10. CLS
9. RASTER MASK SETUP (+)
1. MASK OFF
2. RST MASK 01
• • • • •
10. PATTERN MASK SETUP (+)
1. MASK OFF
2. PTN MASK 01
• • • • •
11. COMBI MASK SETUP (+)
1. MASK OFF
2. CMB MASK 01
• • • • •
PDP-5020FD
3
4
The software versions for each microcomputer
The Flash memory versions for each device
The shutdown message ID/event times
(Going Clear mode by [ENTER/SET] key)
Select Yes by [l] key l pushing and hold [ENTER/SET] key
The temperature/FAN rotating status/Room Light Sensor
The HOUR METER/P-COUNT information
Select Yes by [l] key l pushing and hold [ENTER/SET] key
The information of HDMI information files
The information of HDMI information files
The signal information of VDEC
The signal information of VDEC
Refer to [PANEL FACTORY MODE]
For production line use
For production line use
For production line use
For technical analysis
For technical analysis
For technical analysis
For factory use
Set to Factory default settings (it should perform after
replacing a MAIN Assy)
Information for the Digital Tuner Service Menu is displayed
For technical analysis
For transferring backup data (after replacement of
the DIGITAL Assy)
Change the adjustment status of the DIGITAL Assy.
For clearance of data for the corresponding items.
The clearing method is the same: Select "CLEAR",
then hold [ENTER/SET] pressed for at least 5
seconds.
Switch the Mirror display mode.
Switch the function when checking the color sensor
level.
For use while the Raster Mask is displayed.
Use [i] or [j] to select the type of mask.
Use [l] or [k] to select the sequence.
For use while the Pattern Mask is displayed.
Use [i] or [j] to select the type of mask.
Use [l] or [k] to select the sequence.
For use while the Combination Mask is displayed.
Use [i] or [j] to select the type of mask.
Use [l] or [k] to select the sequence.
4