Quick Reference; Notes, Pd/Sd Diagnosis, And Methods For Various Settings - Pioneer PDP-5020FD Service Manual

5

3.2 QUICK REFERENCE

Notes, PD/SD diagnosis, and methods for various settings

Notes when visiting for service
1. Notes when disassembling/reassembling
1 Rear case
When reassembling the rear case, the screws must be tightened in a
specific order. Be careful not to tighten them in the wrong order forcibly.
For details, see "Rear Case" in "7. DISASSEMBLY".
2 Attaching screws for the HDMI connector
When attaching the HDMI connector after replacing the Main Assy,
secure the HDMI connector manually with a screwdriver, but not
with an electric screwdriver. If you tighten the screws too tightly
with an electric screwdriver, the screw heads may be damaged, in
which case the screws cannot be untightened/tightened any more.
2. On parts replacement
1 How to discharge before replacing the Assys
A charge of significant voltage remains in the Plasma Panel even
after the power is turned off. Safely discharge the panel before
replacement of parts, in either manner indicated below:
A: Let the panel sit at least for 3 minutes after the power is turned off.
B: Turn the Large Signal System off before the power is turned off
then, after 1 minute, turn the power off.
For details, see "5.6 [1] PANEL DRIVE-POWER ON/OFF
FUNCTION".
2 On the settings after replacement of the Assys
Some boards need settings made after replacement of the Assys.
For details, see "8. EACH SETTING AND ADJUSTMENT".
3. On various settings
1 Setting in Factory mode
After a Mask indication into the panel is performed, be sure to
set the Mask setting to "OFF" then exit Factory mode.
How to locate several items on the Factory menu
{ } : Item on the Factory menu
[ ] : Key on the remote control unit
" " : Screen indication
1. Confirmation of accumulated power-on time and power-on
count
Select {INFORMATION} then {HOUR METER}.
(After entering Factory mode, press [j] four times.)
2. Confirmation of the Power-down and Shutdown histories
1 Panel system
PD: Select {PANEL FACTORY} then {POWER DOWN}.
(After entering Factory mode, press [MUTING] once, press
[ENTER/SET], then press [j] two times.)
SD: Select {PANEL FACTORY} then {SHUT DOWN}.
(After entering Factory mode, press [MUTING] once, press
[ENTER/SET], then press [j] three times.)
2 MTB section
Select {INFORMATION} then {MAIN NG}.
(After entering Factory mode, press [j] two times.)
3. How to display the Mask indication
1 Mask indication in the panel side
1. Select {PANEL FACTORY} then {RASTER MASK SETUP}.
(After entering Factory mode, press [MUTING] once, press
[ENTER/SET], then press [j] 8 times.)
2. Press [ENTER/SET], then select a Mask indication, using [i] or [j].
5
6
Quick Reference upon Service Visit 1
SQ_LSI
Module device communication
DIGITAL-RST2
Panel temperature
Audio
Module UCOM communication
Main 3-wire serial communication
Main IIC communication
Main UCOM communication
FAN
Unit high temperature
D-TUNER communication
MTB-RST2/RST4
Main EEPROM
MR POWER
POWER
SCAN
SCN-5V
Y-DCDC
Y-SUS
ADRS
X-DCDC
X-SUS
DIG-DCDC
UNKNOWN
Adjustments and Settings after replacement of the
Assys (Procedures in Factory mode)
1. Digital Video Assy: Transfer of backup data
1 Select {PANEL FACTORY}, {ETC}, then {BACKUP DATA}. (After entering Factory
2 Select {TRANSFER}, using [l], then hold [ENTER/SET] pressed for at least 5
3 After transfer of backup data is completed, {ETC} is automatically selected, and the
2. MAIN Assy: Execution of FINAL SETUP.
1 Select {INITIALIZE} then {FINAL SETUP}, then press [ENTER/SET]. (After entering
2 Select "YES", using [l]. Then hold [ENTER/SET] pressed for at least 5 seconds.
3 After "FINAL SETUP IS COMPLETE" is displayed on the screen, turn the POWER
3. POWER SUPPLY Unit: Clearance of the accumulated power-on count
and maximum temperature value
1 Select {PANEL FACTORY}, {ETC}, then {P COUNT INFO}. (After entering Factory
2 Press [l] to select "CLEAR". Hold [ENTER/SET] pressed for at least 5 seconds.
4. Other Assys: Clearance of the maximum temperature value
1 Select {PANEL FACTORY}, {ETC}, then {MAX TEMP}. (After entering Factory mode,
2 Press [l] to select "CLEAR". Hold [ENTER/SET] pressed for at least 5 seconds.
PDP-5020FD
6
7
Subcategory confirmation procedure
PD/SD
If the DISPLAY key is pressed during
No. of LEDs
shutdown, the orange LED flashes.
flashing For indication patterns other than
Item
described below, see 5.4 [2].
Red Blue
SD
Blue 1
Blue 2
2
Blue 3
Blue 4
4
Blue 5
Blue 6
Blue 7
Blue 8
Blue 9
8
Blue 10
Blue 11
Blue 12
Blue 13
13
Blue 15
LED Display Information
Red 1
For indication patterns other than
Red 2
described below, see 5.1 [1].
Red 3
Red 4
1
Red 6
Red 7
2
Red 8
Red 10
3
Red 11
Red 12
4
Red 15
mode, press [MUTING] once, press [ENTER/SET], press [j] seven times, then
press [ENTER/SET].)
seconds.
LED on the front panel returns to normal lighting.
Factory mode, press [MUTING] three times, then press [j] four times.)
switch of the main unit off.
mode, press [MUTING] once, press [ENTER/SET], press [j] seven times, press
[ENTER/SET], then press [j] six times.)
After clearance is completed, "ETC" is automatically selected. Clear the maximum
temperature value (MAX TEMP) in the same manner.
press [MUTING] once, press [ENTER], press [j] seven times, press [ENTER/SET],
then press [j] seven times.)
After clearance is completed, "ETC" is automatically selected.
7
8
SD Subcategory
1 EEPROM
2 BACKUP
3 DAC
1 PANEL high temperature
2 PANEL low temperature
1 Tuner 1
2 MSP/MAP
3 AV Switch
4 RGB Switch
5 Main VDEC
6 VDEC-SDRAM
7 AD/PLL
8 HDMI
11 US-MSP
1 RST2
2 RST4
Rewriting software
B
R
No backup
B
R
PD (2-15)
B
R
SD (1-15)
B
R
17
8
A
B
C
D
E
F