HP FlexNetwork HSR6600 Configuration Manual page 120
Comware 7 mpls
Hide thumbs
Also See for FlexNetwork HSR6600:
- Command reference manual (542 pages) ,
- Troubleshooting manual (41 pages) ,
- Security configuration manual (559 pages)
Table of Contents
Advertisement
[RouterB-GigabitEthernet1/1/2] quit
# Configure Router C.
[RouterC] mpls lsr-id 3.3.3.3
[RouterC] mpls te
[RouterC-te] quit
[RouterC] interface gigabitethernet 1/1/1
[RouterC-GigabitEthernet1/1/1] mpls enable
[RouterC-GigabitEthernet1/1/1] mpls te enable
[RouterC-GigabitEthernet1/1/1] quit
4.
Configure MPLS TE attributes of links:
# Set the maximum link bandwidth and maximum reservable bandwidth on Router A.
[RouterA] interface gigabitethernet 1/1/1
[RouterA-GigabitEthernet1/1/1] mpls te max-link-bandwidth 10000
[RouterA-GigabitEthernet1/1/1] mpls te max-reservable-bandwidth 5000
[RouterA-GigabitEthernet1/1/1] quit
# Set the maximum link bandwidth and maximum reservable bandwidth on Router B.
[RouterB] interface gigabitethernet 1/1/1
[RouterB-GigabitEthernet1/1/1] mpls te max-link-bandwidth 10000
[RouterB-GigabitEthernet1/1/1] mpls te max-reservable-bandwidth 5000
[RouterB-GigabitEthernet1/1/1] quit
[RouterB] interface gigabitethernet 1/1/2
[RouterB-GigabitEthernet1/1/2] mpls te max-link-bandwidth 10000
[RouterB-GigabitEthernet1/1/2] mpls te max-reservable-bandwidth 5000
[RouterB-GigabitEthernet1/1/2] quit
# Set the maximum link bandwidth and maximum reservable bandwidth on Router C.
[RouterC] interface gigabitethernet 1/1/1
[RouterC-GigabitEthernet1/1/1] mpls te max-link-bandwidth 10000
[RouterC-GigabitEthernet1/1/1] mpls te max-reservable-bandwidth 5000
[RouterC-GigabitEthernet1/1/1] quit
5.
Configure an MPLS TE tunnel on Router A:
# Configure the MPLS TE tunnel interface Tunnel 0.
[RouterA] interface tunnel 0 mode mpls-te
[RouterA-Tunnel0] ip address 6.1.1.1 255.255.255.0
# Specify the tunnel destination address as the LSR ID of Router C.
[RouterA-Tunnel0] destination 3.3.3.3
# Configure MPLS TE to use a static CRLSP to establish the tunnel.
[RouterA-Tunnel0] mpls te signaling static
[RouterA-Tunnel0] quit
6.
Create a static CRLSP:
# Configure Router A as the ingress node of the static CRLSP, and specify the next hop
address as 2.1.1.2, outgoing label as 20, and bandwidth for the tunnel as 2000 kbps.
[RouterA] static-cr-lsp ingress static-cr-lsp-1 nexthop 2.1.1.2 out-label 20
bandwidth 2000
# On Router A, configure Tunnel 0 to use the static CRLSP static-cr-lsp-1.
[RouterA] interface tunnel0
[RouterA-Tunnel0] mpls te static-cr-lsp static-cr-lsp-1
[RouterA-Tunnel0] quit
110
Advertisement
Table of Contents
