Yamaha Star XVS13AA(C) 2011 Service Manual page 93

CABLE ROUTING (for XVS13AA(C)/XVS13CTA(C))
1. Clutch cable
2. Left handlebar switch lead
3. Meter assembly lead
4. Sidestand switch coupler
5. Oil level switch coupler
6. Radiator fan motor coupler
7. Coolant temperature sensor coupler
8. Intake air pressure sensor
9. Left handlebar switch couplers
10. Rear cylinder ignition coil
11. Front cylinder ignition coil
12. Rear cylinder thermostat inlet hose
13. Front cylinder thermostat inlet hose
14. Front cylinder spark plug cap
15. Oil level switch
16. Starter motor lead
17. Sidestand switch lead
18. Oil level switch lead
19. Radiator fan motor lead
20. Front brake hose
21. Wire harness
22. Front cylinder spark plug lead
23. Front cylinder left cover
24. Fuel hose
25. Sub-wire harness
26. Coolant reservoir hose
A. Route the meter assembly lead under the left
handlebar switch lead and clutch cable.
B. Fasten the left handlebar switch lead, front cylinder
spark plug lead, and wire harness with a plastic
locking tie, making sure to align the tape on the
harness with the tie. Be sure to install the plastic
locking tie on the left handlebar switch lead's
protective sleeve and position it 10
0.59 in) from the end of the sleeve. Point the end of
the plastic locking tie downward, to the inside of
the front cylinder left cover.
C. Route the front cylinder spark plug lead to the
outside of the rear cylinder spark plug lead.
D. Black connectors
E. White connectors
F. Connect the ignition coil leads with the "I" marks to
the front cylinder ignition coil.
G. Fasten the wire harness to the ignition coil bracket
with a plastic locking tie. Position the end of the
plastic locking tie to the inside of the other leads.
H. Route the sub-wire harness to the inside of the fuel
pipe.
I. To engine
J. Fasten the sidestand switch lead, starter motor
lead, and oil level switch lead with a plastic locking
tie. Point the end of the plastic locking tie
downward, and then cut off the excess end of the
tie.
K. Route the starter motor lead so that it does not
protrude below the frame.
L. Fasten the starter motor lead at the gray tape to
the engine mounting boss with a plastic locking tie.
Make sure that the starter motor lead does not
contact the engine bracket on the frame. Position
the end of the plastic locking tie between the
radiator bracket mounting boss and the frame.
M. Fasten the oil level switch lead and sidestand
N. Fasten the sidestand switch lead and oil level
O. Route the radiator fan motor lead to the front of the
P. Fasten the sidestand switch lead, oil level switch
Q. Route the sidestand switch lead, radiator fan motor
R. Fasten the sidestand switch lead to the frame with
S. Fasten the sidestand switch lead, oil level switch
T. Point the end of the plastic locking tie downward,
– –
15 mm (0.39
2-66
switch lead with a plastic locking tie. Point the end
of the plastic locking tie rearward, and then cut off
the excess end of the tie.
switch lead with the holder. Face the catch of the
holder outward.
fuel tank breather hose and fuel tank overflow
hose.
lead, and radiator fan motor lead with the holder.
Face the catch of the holder outward.
lead, and oil level switch lead to the front of the
radiator inlet hose.
a plastic locking tie. The oil level switch lead and
radiator fan motor lead may also be fastened with
the plastic locking tie. Point the end of the plastic
locking tie rearward, making sure that it does not
contact the left side panel.
lead, and radiator fan motor lead with the plastic
band. Point the end of the plastic band rearward.
Do not install the plastic band on the couplers or
the sections of the leads that are not covered by
the protective sleeves.
to the inside of the fuel hose.