DSC pc1565 Installation Manual page 45

$SSHQGL[ % 3URJUDPPLQJ /&' .H\SDGV
If you have an LCD5500Z keypad, additional programming is required for proper operation. All LCD programming is done per key-
pad. If more than one LCD keypad are present on the system, labels programmed at one keypad can be broadcast to all other
LCD keypads. Check the software version of the keypad you are programming, and refer to the correct programming instructions.
LCD5500Z v2.x and Lower Keypads
The following is a description of the available programming
options and their accompanying programming sections:
How to Enter LCD Programming
Programming LCD keypads is similar to programming the rest of
the system. Follow the programming procedure as outlined in
Section 3 of the Installation Manual.
1. Enter keypad programming by pressing [*][8][Installer's Code].
2. Press the [*] key.
3. Enter the two-digit section number to be programmed.
Programmable Labels
Zone labels and other LCD display identifiers can be customized
to make operation of the system easier for the end user. The fol-
lowing procedure should be used for creating all LCD labels:
1. Enter Installer Programming. Enter the two-digit section num-
ber for the label to be programmed.
[01] to [32] Zone Labels (14 Characters)
Default: "Zone 1" - "Zone 32"
[33] Fire Alarm Label (14 Characters)
Default: "Fire Zone"
[34] and [35] Partition Labels (14 Characters)
Default: "System"
Default: "Partition 2"
[40] Partition 1 and [41] Partition 2 "Command Output 1" Label (14 Characters)
Default: "Command_O/P_1"
Default: "Command_O/P_1"
[44] Partition 1 and [45] Partition 2 "Command Output 2" Label (14 Characters)
Default: "Command_O/P_2"
Default: "Command_O/P_2"
[46] Partition 1 and [47] Partition 2 "Command Output 3" Label (14 Characters)
Default: "Command_O/P_3"
Default: "Command_O/P_3"
[48] Partition 1 and [49] Partition 2 "Command Output 4" Label (14 Characters)
Default: "Command_O/P_4"
Default: "Command_O/P_4"
[51] Fail to Arm Event Message
Default: "System Has Failed to Arm"
[52] Alarm When Armed Event Message
Default: "Alarm Occurred While Armed < >"
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
3. Use the arrow keys (<>) to move the underline bar under-
neath the letter to be changed.
4. Press the number key [1] to [9] corresponding to the letter
you require. The first time you press the number the first let-
ter will appear. Pressing the number key again will display the
next letter. Refer to the following chart:
[1] - A, B, C, 1
[2] - D, E, F, 2
[3] - G, H, I, 3
[4] - J, K, L, 4
[5] - M, N, O, 5
5. When the required letter or number is displayed use the
arrow keys (<>) to scroll to the next letter.
6. When you are finished programming the Zone Label, press
the [*] key, scroll to "Save," then press [*].
7. Continue from Step 2 until all Labels are programmed.
[6] - P, Q, R, 6
[7] - S, T, U, 7
[8] - V, W, X, 8
[9] - Y, Z, 9,0
[0] - Space