DSC pc1565 Installation Manual page 43

$SSHQGL[ $ 5HSRUWLQJ &RGHV
The following tables contain Contact ID and Automatic SIA for-
mat reporting codes. For more information on reporting code
formats and notes about individual reporting codes, see sec-
tions 5.8 "Communicator – Reporting Codes" on page 16 and
5.9 "Communicator – Reporting Formats" on page 17.
Contact ID
The first digit (in parentheses) will automatically be sent by the
control. The second two digits are programmed to indicate
specific information about the signal.
For example, if zone 1 is an entry/exit point, you could pro-
gram the event code as [34]. The central station would
receive the following:
%85*  (175<(;,7  
where the "1" indicates which zone went into alarm.
6HFWLRQ 5HSRUWLQJ &RGH
[320] Zone Alarms
[324] Zone Restorals
[330] Zone Tamper/Restoral
[334]
[328] Duress Alarm
[328] Opening After Alarm
[328] Recent Closing
[328] Zone Expander Supervisory
Alarm/Rest.
[328] Cross Zone (Police Code)
Alarm
[329] [F] Key Alarm/Rest.
[329] [A] Key Alarm/Rest.
[329] [P] Key Alarm/Rest.
[329] PGM2 Alarm/Rest.
[338] General System
Rest.
[338] Keypad Lockout
[339-343] Closings
[343] Partial Closing
[343] Special Closing
[344-348] Openings
[348] Auto Arm Cancellation
[348] Special Opening
[349-350] Battery Trouble/Rest.
* A/R = alarms/restorals;T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions
&RGH 6HQW :KHQ
zone goes into alarm
alarm condition has been restored
zone exhibits a tamper condition/tamper condition
restored
duress code entered at keypad
system disarmed with alarm in memory
alarm occurs within two minutes of system arming
panel loses/restores supervisory transmission over the
Keybus from enrolled PC5132 module or keypads with
zone inputs
two zones on the same partition go into alarm during
any given armed-to-armed period (incl. 24Hr zones)
Keypad fire alarm (alarm and restore rep. codes sent
together)
Keypad auxiliary alarm (alarm and restore rep. codes
sent together)
Keypad panic alarm (alarm and restore rep. codes sent
together)
a panic button wired to PGM2 is pressed / access code
is entered (PGM2 programmed as option [23] or [24])
Tamper/ enrolled module with tamper inputs has a tamper alarm/
all module tampers restored
max. number of incorrect access codes has been
entered at a keypad
system armed (user 01-34, 40-42 indicated)
one or more zones bypassed when system armed
Closing (arming) using one of the following methods:
quick arm, auto arm, keyswitch, function key, mainte-
nance code, DLS software
system disarmed (user 01-34, 40-42 indicated)
auto arm cancelled
Opening (disarming) using one of the following meth-
ods: keyswitch, maintenance code, DLS software
PC1565 battery is low/battery restored
SIA Format - Level 2 (Hardcoded)
The SIA communication format used in this product follows the
level 2 specifications of the SIA Digital Communication Stan-
dard - January 1996. This format will send the Account Code
along with its data transmission. The transmission would look
similar to the following at the receiver:
N Ri01
N =
Ri01 =
BA =
01 =
'LDOHU
'LUHFWLRQ
A/R
A/R
T/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
T/R
T/R
O/C
O/C
O/C
O/C
O/C
O/C
MA/R
** UU = user number (user01-42); ZZ = zone number (01-08)
BA 01
New Event
Partition /Area Identifier
Burglary Alarm
Zone 1
&RQWDFW 6,$ $XWR 5HS
,' &RGHV &RGHV
(1) 3A See Table 3
(1) 3A
(1) 44 TA-ZZ/TR-ZZ
(1) 21 HA-00
(4) A6 OR-00
(4) 59 CR-00
(1) 43 UA-00/UH-00
(1) 4A BV-00
(1) 15 FA-00/FH-00
(1) AA MA-00/MH-00
(1) 2A PA-00/PH-00
(1) 4A UA-99/UH-99
(1) 45 TA-00/TR-00
(4) 21 JA-00
(4) A2 CL-UU
(4) 7A CG-ZZ
(4) AA CL-00
(4) A2 OP-UU
(4) A5 CE-00
(4) AA OP-00
(3) A2 YT-00/YR-00