Table of Contents
Advertisement
Turbo Timer
This function allows you to set the timer recording
program without going through the regular set up
with the on screen. The extent of programming is
24 hours from the current time.
1 Insert a tape into the VCR and press the
"TURBO TIMER" button on the remote control.
"
" (start time Prompt) and the current
time appears alternately on the display.
2 To change the START time, press the PLAY
∞
STOP
button (if you press and hold either
button, the time changes in 30-minutes incre-
ments), then press OK/STATUS.
Then,"
" (stop time prompt) and the set
start time appears alternately on the display.
3 To change the STOP time, press the PLAY
∞
STOP
button (if you press and hold either
button, the time changes in 30-minutes incre-
ments), then press OK/STATUS.
Channel number will appear on the display.
4 To change the CHANNEL number, press the
5
∞
PLAY
or STOP
5 The data input will be memorized and the Turbo
Timer mode will be finished so that normal
display appears.
6 Turn off the VCR.
Notes:
• To exit Turbo Timer mode at any step, press the TURBO
TIMER button.
• If "Err" appears on the display panel, all eight
programs have been set and Turbo Timer will not
proceed. To remove the error message, press the
TURBO TIMER button again.
• Settings of Turbo Timer will appear on the display panel
only and not on the screen.
• Programs Overlap Warning does not function with
Turbo Timer.
• DAILY or WEEKLY programming are not available on
Turbo Timer.
5
, then press OK/STATUS.
• Tape speed can be selected by pressing the ALT/SPEED
button anytime during steps 1 through 4.
The speed appears on the display for about 5 seconds.
When two programs overlap
The Program Review screen will
appear with a magenta line
blinking on the newly set timer
recording while the other
overlapped program blinking.
1 Press PLAY
5
line among the two overlapping programs.
or
2 Press OK/STATUS to view
the detail information of the
program you want to change.
3 Go to step 4 through 8 to
modify the selected program.
To cancel any timer recording,
press CLEAR.
• If you do not modify the overlapping programs,
the VCR will record the earlier program com-
pletely. Only the remaining part of the later
or
program will be recorded.
• If the START time for the two programs are the
same, the lower program number will be re-
corded.
Useful function for Timer Recording:
Auto Tape Speed
With this function activated, the VCR can change
the tape speed and record the programme in LP or
SLP mode if not enough tape remains for recording
in SP mode.
1 Press VCR.
2 Press MENU.
3 Press PLAY
UP" then press OK/STATUS.
4 Press PLAY
REC SPEED."
3
5 Press FF
setting changes.
AUTO:
Select this to allow the VCR to change the tape speed
from SP to LP (or SLP) when there is not enough
tape length remaining.
MANUAL:
Select this not to allow the VCR to change the tape
speed.
6 Press MENU to exit from the menu operations.
13
PR CH START STOP DATE
1
2
3
4
5
6
7
8
SELECT:
5
∞
or STOP
to move the magenta
ONE TIME PROGRAM
ERASE: CLEAR
NEXT: OK
5
∞
or STOP
to select "VCR SET
5
∞
or STOP
to select "TIMER
. Each time you press the button, the
12 20:00 22:00
20/07
20 11:00 11:30
15/10
24 15:00 16:00
10/08
45 21:00 23:00
FRI
CONFIRM: OK
PROGRAM
1
CHANNEL+/–
12
START +/–
20 : 00
STOP +/–
22 : 00
REC SPEED SP
DATE +/–
20/07/01
FRIDAY
END: TIMER
Advertisement
Table of Contents
