Table of Contents
Advertisement
Timer Recording
To record while you're away, follow step 1 — 9
below. For each programme you set, the VCR will
turn on, start recording, and turn off automatically.
You can store up to 8 programmes.
FOR EACH STEP BELOW, YOU NEED TO FINISH
WITHIN 60 SECONDS; OTHERWISE,
PROGRAMMING WILL HAVE TO BE RESTARTED
FROM STEP 1.
1
Select Timer Mode
1 Press VCR.
2 Press TIMER. The Timer
Recording menu appears.
2
Select Programme mode
5
Press PLAY
or STOP
select "QUICK PROGRAMM-
ING", then press OK/STATUS.
The Quick Programming menu
appears.
• If you have already set 8 programmes, "ALL PRO-
GRAMS IN USE" appears and goes back to the Timer
Recording menu. If this happens, delete unwanted
programmes. ( P.14)
3
Select Channel
5
∞
Press CH
5
or
to enter the TV channel.
• Holding down CH
channels.
• To record from external line input, press CH
until "A/V REAR" or "A/V FRONT" appears.
4
Select Start Time
Press START + or – (Number button 1 or 4).
• Each time you press the button, the set time changes by
1-minute intervals. If you hold the button, the set time
changes by 30-minute intervals.
5
Select Stop Time
Press STOP + or – (Number
button 2 or 5).
• Each time you press the button,
the set time changes by 1-minute
intervals. If you hold the button,
the set time changes by 30-minute
intervals.
QUICK PROGRAMMING
PROGRAM REVIEW
SELECT:
END: TIMER
∞
to
ONE TIME PROGRAM
PROGRAM
CHANNEL+/–
START +/–
STOP +/–
REC SPEED SP
DATE +/–
DAILY: 8
CONFIRM: OK
∞
or
rapidly scans through the
5
ONE TIME PROGRAM
PROGRAM
1
CHANNEL+/–
12
START +/–
20 : 00
STOP +/–
22 : 00
REC SPEED SP
DATE +/–
– –/– –/– –
DAILY: 8
CONFIRM: OK
6
Select Tape Speed
Press ALT/SPEED.
• Each time you press the button, the tape speed
alternates between SP, LP and SLP.
SP, LP: For PAL signal.
SP, SLP: For NTSC signal.
7
Select Start Date
Press DATE + or – (Number button 3 or 6).
• The year and day of the week are displayed
automatically.
8
Confirm Programme
Press TIMER or OK/STATUS.
"PROGRAM WAS COMPLETED" appears on the
CONFIRM: OK
TV screen.
After 5 seconds, the above message disappears, and
the normal TV picture resumes. The
indicator lights up on the display.
• If "PROGRAM NOT COMPLETED" appears,
1
– –
try again from step 1.
– –:– –
– –:– –
• If "PROGRAM NOT COMPLETED/PRO-
– –/– –/– –
GRAM OVERLAP"
WEEKLY: 9
timer recording you just programmed overlaps another
END: TIMER
timer recording. ( P.13)
If you want to store other programmes, repeat steps
1 to 8.
9
Finish Settings
Press POWER to turn off the VCR.
The VCR must be turned off for a timer recording to take
place. If you forget to turn off the VCR, PLEASE TURN
OFF VCR FOR TIMER RECORDING flashes on your TV
∞
screen two minutes before a timer recording starts. To
or
remove the message, press the CLEAR button.
If you want to record the same programme daily, press
DAILY (Number button 8) during step 3 through 7.
(Press the button again to cancel.)
The VCR will record a TV programme every day
(Monday through Friday) at the same time and length.
(Daily Recording)
If you want to record the same programme weekly,
press WEEKLY (Number button 9) during step 3 through
7. (Press the button again to cancel.)
The VCR will record a TV programme once a week at the
same day, time and length. (Weekly Recording)
If you want to cancel the currently set programme,
press CLEAR.
After a timer recording has taken place
Press POWER to turn on the VCR. You can operate your
VCR normally.
WEEKLY: 9
To stop a started timer recording
END: TIMER
Press POWER.
Recording stops and the VCR turns off.
If it is a Daily or Weekly Recording, future recordings
will be carried out as programmed.
12
(Timer)
appears on the TV screen, the
Advertisement
Table of Contents
