Table of Contents
Advertisement
9
Finish Settings
Press POWER f to turn off the VCR.
The VCR must be turned off for a timer
recording to take place. If you forget to turn off
the VCR, "PLEASE TURN OFF VCR FOR
TIMER RECORDING" flashes on your TV
screen two minutes before a timer recording
starts. To remove the message, press the CLEAR
button.
If you want to record the same programme
daily, press DAILY (Number button 8) during
step 3 through 7. (Press the button again to
cancel).
The VCR will record a TV programme every day
(Monday through Friday) at the same time and
length (Daily Recording).
If you want to record the same programme
weekly, press WEEKLY (Number button 9)
during step 3 through 7. (Press the button again
to cancel).
The VCR will record a TV programme once a
week at the same day, time and length (Weekly
Recording).
After a timer recording has taken
place
Press POWER f to turn on the VCR. You can
operate your VCR normally.
To stop a started timer recording
Press POWER f.
Recording stops and the VCR turns off.
If it is a Daily or Weekly Recording, future
recordings will be carried out as programmed.
When two programs
overlap
The Program Review screen
will appear with a magenta
line blinking on the newly set
timer recording while the other
overlapped program blinking.
5
1 Press PLAY
or STOP
magenta line among the two overlapping
programs.
2 Press OK/STATUS to view
the detail information of the
program you want to change.
3 Go to step 4 through 8 to
modify the selected program.
To cancel any timer recording, press CLEAR.
• If you do not modify the overlapping programs, the
VCR will record the earlier program completely.
Only the remaining part of the later program willbe
recorded.
• If the START time for the two programs are the
same, the lower program number will be recorded.
220/75
This function allows you to set the timer record-
ing program without going through the regular set
up with the on screen. The extent of program-
ming is 24 hours from the current time.
1 Insert a tape into the VCR and press the
2 To change the START time, press the PLAY
Then,"
start time appears alternately on the display.
3 To change the STOP time, press the PLAY
Channel number will appear on the display.
4 To change the CHANNEL number, press the
PR CH START STOP DATE
1
12 08:00P 10:00
20/07
2
20 11:00A 11:30
15/10
3
24 03:00P 04:00
10/08
4
45 09:00P 11:00
FRI
5
6
7
8
SELECT:
CONFIRM: OK
5 The data input will be memorized and the
∞
to move the
6 Turn off the VCR.
ONE TIME PROGRAM
PROGRAM
1
CHANNEL+/–
12
Notes:
START +/–
08 : 00 PM
STOP +/–
10 : 00 PM
• To exit Turbo Timer mode at any step, press the
REC SPEED SP
DATE +/–
11/23/01
FRIDAY
ERASE: CLEAR
END: TIMER
NEXT: OK
PREV:
• If "Err" appears on the display panel, all eight
• Settings of Turbo Timer will appear on the display panel
• Programs Overlap Warning does not function with
—19—
19
Turbo Timer
"TURBO TIMER" button on the remote
control. "
" (start time prompt) and the
current time appears alternately on the display.
∞
or STOP
button (if you press and hold
either button, the time changes in 30-minutes
increments), then press OK/STATUS.
PM
" (stop time prompt) and the set
∞
or STOP
button (if you press and hold
either button, the time changes in 30-minutes
increments), then press OK/STATUS.
PM
5
∞
PLAY
or STOP
, then press OK/STA-
TUS.
Turbo Timer mode will be finished so that
normal display appears.
TURBO TIMER button.
programs have been set and Turbo Timer will not
proceed. To remove the error message, press the
TURBO TIMER button again.
only and not on the screen.
Turbo Timer.
01.5.11, 4:16 PM
PM
5
PM
5
Advertisement
Table of Contents
