Set The Condensation Prevention Heater; Fine Adjustment Of The Temperature (Refrigerator Compartment / Freezer Compartment); Eco " Operation Indicator Lamp; Door Alarm - Hitachi R-D6800S How To Use Manual

Set the condensation prevention heater

You can save electricity by setting the condensation prevention heater to a weaker level
when the humidity in the room is low.
You can set the swing partition or the partitioning iron plates by 4 stages respectively (Level 4 means the most effective for energy saving).
● Dew condensation may be found in the swing partition or the partitioning iron plates when humidity is high. When dew is formed, cancel the setting.
Notice
● The setting will be cancelled when the power plug is connected and disconnected or power failure recovery takes place.
Setting the swing partition
1
Open the door of the Lower Freezer Compartment.
2
Touch
Panel to turn on the indicator lamp.
All indicator lamps turn on once, and then the current settings are displayed.
3
Press down
more until the preset sound is heard.
Settings of condensation prevention heater (Energy Saving
level) will be changed. Repeat the change of settings to set
the operation sound you like (see the table shown below).
4
Close the door of the Lower Freezer Compartment.
Set the condensation
Level 1 for saving
prevention heater
Preset sound
Long beep
Fine adjustment of the temperature
(Refrigerator Compartment / Freezer Compartment)
Temperature settings for Refrigerator and Freezer
Compartments can be more finely adjusted by 9 levels.
1
Open the door of the Lower Freezer Compartment.
2
Touch
Panel to turn on the indicator lamp.
All indicator lamps turn on once, and then the current settings are displayed.
3
Press down
or more until 1 beep is heard.
4
Close the door of the Lower Freezer Compartment.
5 Touch or
an adjustment.
The temperature becomes higher by 1 level every time you touch the
button. (Touching " Max. " returns to " Min. " .)
( Lighting
Indication
lamp
Setting
Min.
Follow the operations shown in Step 1, 2 and 3.
2 beeps sound and you can set the temperature by normal step.
button on the Control
button 3 seconds or
Level 2 for saving
electricity electricity
Long beep (2 beeps) Long beep (3 beeps) Long beep (4 beeps)
button on the Control
button for 5 seconds
button to make
Blinking Turned off)
Mid.
(Swing partition/Partitioning iron plates)
Setting the partition plate
1
Open the door of the Lower Freezer Compartment.
2
Touch
Panel to turn on the indicator lamp.
All indicator lamps turn on once, and then the current settings are displayed.
3
Press down
more until the preset sound is heard.
Settings of condensation prevention heater (Energy Saving
level) will be changed. Repeat the change of settings to set
the operation sound you like (see the table shown below).
4
Close the door of the Lower Freezer Compartment.
Level 3 for saving Level 4 for saving
electricity electricity

" eco " Operation indicator lamp

When the refrigerator is operated in a manner to
reduce power consumption, such as Frost Recycle
Cooling, the indicator lamp is automatically
lit to indicate that the refrigerator is
operating in the energy saving mode.
Notice
If [ " eco " Operation indicator lamp] isn ' t illuminated,
check the following things.
・ Immediately after it is installed, plentiful foods are stored at a time or
the door is opened / closed frequently
・ " Quick Freeze " , " Quick Cool " , " Quick " or " Vegetable " is set.
・ The ambient temperature of the refrigerator is about 35˚C or higher.

Door Alarm

When the door is opened for more than 1 minute, sound and light
occur indicating the door is open as shown in the table below.
The Refrigerator Compartment, Ice Compartment, Lower Freezer and Vegetable
Compartment have the Door Alarm function (, but the Upper Freezer doesn ' t).
Duration when
door is open
Long beep (3
Alarm sound
Display
Control Panel
Max.
※ From 30 seconds onwards with the door opened, the Door Alarm
sounds only when the energy saving mode is set. (In this case the
indicator lamp on the Control Panel wouldn ' t blink.)
※ When the indicator lamp on the display area blinks due to the Door
Alarm function, the Control Panel will not be activated by touching it.
Swing partition
Partitioning iron plates
button on the Control
button 3 seconds or
The energy saving mode
Deactivate
of the condensation
prevention heater is set
2 beeps
to off before shipping.
" eco "
Operation
indicator
lamp
1 minute 2 minutes
Long beep (5
beeps) beeps)
It blinks. It blinks.
Lamp on. Lamp on.
3 minutes
Long beep
(continuously),
Louder
It blinks.
Lamp on.
55